Polycom Realpresence group convene Manuel utilisateur

ENGLISH

www.polycom.com

sociated with Polycom’s products are trademarks and/or service marks of Polycom,

Inc. and are registered and/or common law marks in the United States and various

other countries. No portion hereof may be reproduced or transmitted in any form or

by any means, for any purpose other than the recipient’s personal use, without the

express written permission of Polycom.

P/no. MFL69143011 (1503-REV00)

Set Up the Polycom® RealPresence® Group Convene™

Display AC/DC adapter 4 AC Power

adapters

Stand body

Stand base Screws (4 pcs)

(M4 X L10)

Cable cover Rear cover

HDMI cable DC-to-DC jumper

cable

2 Screws and

2 T-Nuts

Easy Setup Guide

*MFL69143011*

ENGLISH

ASSEMBLE THE STAND

Use the packing material from the

lower portion of the display as a

platform for assembly.

Do not stand the unit up until the

installation and cabling are complete.

INSTALL THE CAMERA

Unpack the RealPresence Group Series co-

dec and camera. Reserve the codec power

supply for future use.

Power supply

Only use the power supply

provided with the display

accessory.

Open the hinge on the camera and insert the hinge into the camera

bracket on the rear top of the display.

Gather the excess cable and secure with the cable ties.

ENGLISH

ASSEMBLE THE STAND

Use the packing material from the

lower portion of the display as a

platform for assembly.

Do not stand the unit up until the

installation and cabling are complete.

INSTALL THE CAMERA

Open the hinge on the camera and insert the hinge into the camera

bracket on the rear top of the display.

Gather the excess cable and secure with the cable ties.

Do not carry display by holding the base.

Do not carry the display upside down by just holding the

base. This may cause the display to fall off the stand and

could result in personal injury.

ENGLISH

CONNECT CABLES

Plug the DC-to-DC jumper between the

display and the codec.

Connect and route all cables through the

cable management channel.

Note: Generic cables

If you use generic cables

not certied by LG and

Polycom, the screen may

not display or there may

be image noise.

INSTALL THE CODEC

Install the RealPresence Group Series codec by inserting the T-nuts into

the keyholes on the back of the display.

Connect the DC power, LAN, HDMI, and camera cables to the codec. Refer

to the RealPresence Group Series 500 Setup Sheet for details.

Route the LAN and DC power supply cables between the codec and dis-

play and then through the cable channel at the rear of the stand.

PREPARE THE CODEC

HDMI IN

DC-OUT

(12V 2.7 A)

DC-IN

(12V )

ENGLISH

CONNECT CABLES

INSTALL THE CODEC

Install the RealPresence Group Series codec by inserting the T-nuts into

the keyholes on the back of the display.

Connect the DC power, LAN, HDMI, and camera cables to the codec. Refer

to the RealPresence Group Series 500 Setup Sheet for details.

Route the LAN and DC power supply cables between the codec and dis-

play and then through the cable channel at the rear of the stand.

PREPARE THE CODEC

HDMI IN

DC-OUT

(12V 2.7 A)

DC-IN

(12V )

HDMI IN

DC-OUT

(12V 2.7 A)

DC-IN

(12V )

HDMI IN

DC-OUT

(12V 2.7 A)

DC-IN

(12V )

ENGLISH

Stand Hinge

Cable cover

MANAGE THE CABLES

Arrange the cables so that they run below the stand hinge and then cover

them with the cable cover from the bottom up.

You can disassemble the cable cover by following the assembly instruc-

tions in reverse order.

INSTALL THE REAR COVER

Install the rear cover on the stand by tting the hooks on the cover into

the slots on the back of the display and sliding into place.

ENGLISH

MANAGE THE CABLES

Arrange the cables so that they run below the stand hinge and then cover

them with the cable cover from the bottom up.

You can disassemble the cable cover by following the assembly instruc-

tions in reverse order.

INSTALL THE REAR COVER

Install the rear cover on the stand by tting the hooks on the cover into

the slots on the back of the display and sliding into place.

ENGLISH

CONNECT THE HEADPHONES (OPTIONAL)

CONNECT POWER

DC Switch

(shipped

with codec)

Caution: Power on DC switch rst.

Power on the DC switch on the bottom of the product

before turning on the display.

Four AC power adapter cables are supplied with the display. Select the ap-

propriate AC power adapter cable for your geographic region. Connect the

cable to the power supply input. Connect the AC power cable, provided

with the RealPresence Group Series codec, to the AC power adapter cable.

ENGLISH

CONNECT THE HEADPHONES (OPTIONAL)

Bottom Center of

the Display

CONNECT POWER

Four AC power adapter cables are supplied with the display. Select the ap-

propriate AC power adapter cable for your geographic region. Connect the

cable to the power supply input. Connect the AC power cable, provided

with the RealPresence Group Series codec, to the AC power adapter cable.

ENGLISH

Power/Menu buttons

POWER ON THE SYSTEM

Power on the display. When the Automatic Standby message appears,

select Yes to disable Automatic Standby. Otherwise, the display will go

into Automatic Power Down after four hours and it will not wake up for

a video call without manually turning on the display. When the codec

nishes booting up, refer to the Polycom RealPresence Group Series

Administrator Guide for details on codec settings conguration and IP

connectivity.

ADJUST THE ANGLE

Automatic Standby

Automatic Standby is currently set at 4 hours.

Would you like to disable Automatic Standby?

Yes No

Press "OK" button to select.

OK EXIT

Autres manuels pour realpresence group convene

Table des matières

Autres manuels Polycom Système de conférence

Polycom

Polycom NOT FOUND VTX 1000 Comment utiliser

Polycom

Polycom VSX 7000e Series Manuel utilisateur

Polycom

Polycom RMX DOC2557C Instructions d'installation

Polycom

Polycom RealPresence Group Series Manuel utilisateur

Polycom

Polycom QSX Manuel de service

Polycom

Polycom Studio P009 Manuel utilisateur

Polycom

Polycom RealPresence Trio 8500 Manuel utilisateur

Polycom

Polycom RealPresence Group Manuel utilisateur

Polycom

Polycom SIP 3.1 Manuel de service

Polycom

Polycom realpresence trio 8800 Manuel utilisateur

Polycom

Polycom MGC-25 Comment utiliser

Polycom

Polycom RealPresence Group Series Instructions de montage

Polycom

Polycom QSX Manuel utilisateur

Polycom

Polycom VSX 3000 Manuel utilisateur

Polycom

Polycom CX5500 Manuel utilisateur

Polycom

Polycom VSX Series Manuel utilisateur

Polycom

Polycom SoundStation 2W Manuel de service

Polycom

Polycom RealPresence EduCart 500 Manuel

Polycom

Polycom MGC+50 ReadiConvene Manuel utilisateur

Polycom

Polycom Real-Time Media Conferencing Platform RMX... Manuel utilisateur

Polycom

Polycom VSX 7000 Instructions de montage

Polycom

Polycom MSR Series Manuel utilisateur

Polycom

Polycom QDX 6000 System Manuel utilisateur

Polycom

Polycom HDX 7000 Series Manuel utilisateur

Manuels Système de conférence populaires d'autres marques

Kramer

Kramer VIA GO Manuel utilisateur

AVT

AVT MAGIC AC1 Go Manuel utilisateur

ProSoft Technology

ProSoft Technology AN-X4-AB-DHRIO Manuel utilisateur

Sony

Sony PCS-I150 Manuel utilisateur

Middle Atlantic Products

Middle Atlantic Products VTC Series Manuel utilisateur

Prentke Romich Company

Prentke Romich Company Vanguard Plus Mode d’emploi

Speakerbus

Speakerbus iD 712 Manuel utilisateur

Trelleborg

Trelleborg SafePilot CAT PRO Manuel utilisateur

Sennheiser

Sennheiser ADN Manuel utilisateur

ADTRAN

ADTRAN NetVanta 7100 Manuel utilisateur

AINA

AINA PTT Voice Responder Manuel utilisateur

Yamaha

Yamaha ProjectPhone PJP-100H Manuel utilisateur

vissonic

vissonic VLI Series Manuel utilisateur

Panasonic

Panasonic KX-VC500 Manuel utilisateur

Poly

Poly Trio 8300 Manuel utilisateur

Crestron

Crestron Mercury CCS-UCA-SMK Dessin dimensionnel

Inmarsat

Inmarsat mini M Manuel utilisateur

Tenveo

Tenveo ALL-IN-ONE Manuel utilisateur

Polycom realpresence group convene Manuel utilisateur

Manuels Système de conférence populaires d'autres marques