Plextor PL-MAN2 Manuel utilisateur

Hardware Installation

By itself, your CD-ROM drive is incapable of communicating with your computer.

You must use a hardware link that enables your drive to ‘‘talk’’ with the rest of your

computer.

Plextor’s4PleXdrivesuseaSCSIinterfaceastheirlink.IfyouownaPC,therearefour

ways in which you can make the SCSI connection:

1) Useaseparate8-bitor 16-bitSCSIinterface board.Thisis themostcommon

method. We recommend using a 16-bit SCSI interface board to maximize

the drives potential.

2) Use a soundboard that also has a SCSI interface built onto it. This helps save

a slot in your computer by combining the functions of two boards (SCSI

interface board and soundboard) into one. The downside of this is that most

soundboards use only an 8-bit SCSI chip. If you need the performance a

16-bit SCSI interface board provides (see page 32), you’ll have to buy a

separate board.

3) Ifyouhaveanexternaldrive,useaparallel-to-SCSIinterface.Thisisadevice

that plugs into the parallel port (the one your printer normally is connected

to) of your computer. It is convenient, but typically at a cost of reduced

performance by your CD-ROM drive.

4) If you have an external drive and a portable computer with a PCMCIA slot,

useaPCMCIA-to-SCSIcard.Thisisasmall,credit-cardsizedevicethatplugs

into the PCMCIA slot. It too is convenient, but again at a cost of reduced

drive performance.

---- CHAPTER 8 ----

20 PX-43CH/PX-45CH OPERATION MANUAL

NOTE: The following section is only for PC users who need to install a SCSI

interface board, or a soundboard with a built-in SCSI interface, in their

computer. If you plan to use a parallel-to-SCSI, or PCMCIA-to-SCSI

interface,youcanskiptoChapter9.IfyouareaMACuser,youcanlaugh

at how easy life is and skip to page 29.

Board Installation

YOUR TASK: Install a SCSI interface board, or a soundboard with

a built-in SCSI interface, in your computer.

YOUR OBJECTIVE: Provide the hardware link needed to enable your

CD-ROM drive to communicate with your

computer.

YOUR METHOD: Remove your computer’s case. Install board and

attach necessary cables.

Let us point out that this is a CD-ROM drive installation and operation manual ---- it

isnot a SCSI interfaceboardor soundboard installation andoperationmanual. Unless

you purchased a SCSI interface board or soundboard (and its accompanying manual)

bundled in the same box with a 4PleX drive, we have no way of knowing which type

of board you elect to use. There are dozens of SCSI interface boards and soundboards

on the market. Each one is installed somewhat differently. Therefore, our instructions

forthissectionshouldonlybeconsideredasguidelines.Formoredetailedinstructions

on how to properly install your SCSI interface board/soundboard, you should refer to

the installation/operation manual that you received when you purchased the board.

Caution: If static electricity may be present in the room where you are working,

dischargeanyyoumayhaveonyourbodybytouchingagroundedobject

before you remove the host adapter from its packaging.

Static electricity is a silent killer. Just a small jolt to one of the chips on

your interface board may render it useless with no apparent damage

visible. Positioning your computer in a location without a carpet under-

foot is one method of guarding against static electricity damage. Using

common sense, such as not walking on a carpeted floor in stocking feet

just before you install your drive, is another.

Before proceeding, make sure the power to your computer and any

external peripherals is OFF and your computer is UNPLUGGED from its

power source.

CHAPTER 8 ---- Hardware Installation

PX-43CH/PX-45CH OPERATION MANUAL 21

To remove your computer’s cover, follow the directions provided by your computer’s

manufacturer. Typically this involves loosening or removing several screws on the

back panel of your computer and sliding off your computer’s cover.

Carefully remove the SCSI interface board from its packaging. Select a vacant slot in

your computer where you will install the board (refer to the manual packaged with

your interface board for instructions as to which slot in your system to use). Plextor

provides only 16-bit SCSI interface boards with its optional bundles, so you must use

a vacant 16-bit slot (16-bit slots are longer than 8-bit slots). If you install an internal

drive, try to pick a slot that is closest to where the drive will be installed.

Remove the cover plate for this slot from the back panel of your computer. Keep the

screw from the cover plate nearby as you will need it in a moment. Save the cover

plate in case you need it at a later date.

Plug the SCSI interface board into the slot you have selected. Rock the board from

end-to-end to ensure that it seats firmly in the slot. Don’t force it. If you cannot push

the board down completely into the slot, remove the board and try again.

Expansion Slot Cover

Rear Panel

CHAPTER 8 ---- Hardware Installation

22 PX-43CH/PX-45CH OPERATION MANUAL

Onceyouhave successfully inserted the board, fasten it in place using the cover plate

screw that you removed earlier.

CHAPTER 8 ---- Hardware Installation

PX-43CH/PX-45CH OPERATION MANUAL 23

Drive Positioning

YOUR TASK: Determine where you want to install your drive.

YOUR OBJECTIVE: Position the drive in the proper manner so that it

operates correctly.

YOUR METHOD: If you have an internal drive, find an open bay in

your computer. If you have an external drive, find

an open space on your desktop.

The PX-43CH and PX-45CH may be installed either horizontally or vertically. If

installed vertically, make sure that the eject button is positioned near the top of the

drive.

PX43-CH

PX-45CH

Eject Button UP

Vertical Horizontal

CHAPTER 8 ---- Hardware Installation

Vertical Horizontal

Eject Button UP

24 PX-43CH/PX-45CH OPERATION MANUAL

NOTE: The following section is only for those installing internal drives. If you

have an external drive, skip to page 29.

Mounting an Internal Drive

YOUR TASK: Mount your internal drive inside your computer.

YOUR OBJECTIVE: A securely positioned drive whose connectors are

within easy reach of the various cables that must

attach to it.

YOUR METHOD: Identify the drive bay where you will mount your

drive. Remove bay cover. If necessary, use

mounting rails to install drive in bay.

Your PC probably looks something like this:

You can mount your drive in any available bay. You must remove the small panel

that covers the bay that you want to use. This most typically is done after you have

removed your computer’s cover. The panel can then be popped out by pressing

outward lightly (in some older cases you may have to remove screws that hold the

panel in place).

You now need to determine if you must install mounting rails on the sides of your

drive. To do so, insert the drive into the open bay. If the drive fits tightly with little (or

no) clearance on either side of the drive, you will not have to use mounting rails. The

drive can be mounted directly into your computer.

Caution: Donot mountyour drive inyour computer usingscrews other thanthose

supplied by Plextor. You may damage the drive if you insert screws that

aretoo long. Ifyou find thatyou are havingdifficulty inserting orejecting

a caddy from your drive, the cause may be that you are using screws

other than those supplied by Plextor. Another possibility is that you are

using Plextor’s screws, but you have tightened them too much. Try

backing the screws out a few turns and see if this corrects the problem.

Available bay with

cover panel removed.

CHAPTER 8 ---- Hardware Installation

PX-43CH/PX-45CH OPERATION MANUAL 25

If you must use mounting rails, install them as shown below:

There are 4 holes provided on each side of the drive. To mount an internal drive in

most computers, the rails should be fastened to the lower pair of holes. In some

instances you may need to fasten the rails to the upper set of holes.

You will find that 8 screws were supplied with your drive: 4 chrome screws and 4

blackscrews.Selectwhichscrewstousebasedonwhichsetofholesyouusetoattach

the mounting rails.

✓Use the chrome screws if you use the upper set of mounting

holes.

✓Use the black screws if you use the lower set of mounting holes.

Check the positioning of the rails by sliding the drive into the bay before you connect

any cables.

Check Your Jumper Settings

Once you have determined a) the correct set of holes to use to attach mounting rails,

or b) that you don’t have to use mounting rails, you are almost ready to finish your

drive’s installation. However, before doing so, check your jumper settings one last

time.

If you do not have any SCSI peripherals (e.g., hard disk, scanner, printer, etc.) in your

system other than your CD-ROM drive, you should not change the jumpers from their

factory setting.

If you do have other SCSI peripherals as part of your computer system, you may need

to change the settings of the SCSI ID and Terminator. See Chapter 6 and 7 for

information on how to change these settings.

Be sure not to mistake the inner and outer face of

the rail when attaching. The smooth side of the rail

faces away from the drive’s chassis.

CHAPTER 8 ---- Hardware Installation

26 PX-43CH/PX-45CH OPERATION MANUAL

Cable Connections

You must make a minimum of two cable connections to your CD-ROM drive. A third

cableconnectionneed bemadeonly ifyouare usingasoundboardinyour computer.

The two cable connections which you must make are:

1) SCSI cable

2) power cable

The SCSI cable should be a standard 50 pin flat SCSI ribbon cable. You should have

received one at the time you purchased your SCSI interface board. If you did not, you

can purchase one at most computer stores.

CAUTION: It is easy to accidentally plug your SCSI ribbon cable upside down into

bothyourdriveandSCSIinterfaceboard.Accordingly,besureyoumatch

the red stripe along one side of the SCSI cable to pin 1 on the interface

board and pin 1 on the drive (as shown on the next page).

Double-checkyourwork;youmustensurethesideoftheSCSIcablewith

thered stripe is matched to pin 1 on the interface board and on the drive.

Power Supply

from Personal

Computer

DC Power Supply

DC+12V 0.6A

DC+5V 0.3A

SCSI Ribbon Cable

SCSI Host Adapter

Personal Computer

Pin 1

➌Jumpers

➋SCSI Interface Connector

➍Power

Connector

➊Audio Connector

CHAPTER 8 ---- Hardware Installation

PX-43CH/PX-45CH OPERATION MANUAL 27

The easiest way to install your SCSI cable is to plug it into the SCSI connector on the

rear panel of the drive before you insert the drive into your computer. Then you can

thread the cable through the front of the open bay you plan to use and back toward

the SCSI interface board. Connect the cable to your SCSI interface board and finish

mounting your drive in the proper position. The drive should slide smoothly into the

bay.Ifitdoesnot,checkforobstructionsinthebay andensurethesiderails(ifneeded)

are attached properly.

You now need to make the power connection. In most computers you will find

additional power connectors that are ready for your use. Check the cable running

from your power supply to your hard disk and see if it has extra connectors on it. If

so, you can plug one of these into the power connector found on the rear panel of the

CD-ROM drive.

If you do not find any additional connectors available (either because they were not

supplied, or they are all in use), you will have to buy a ‘‘splitter’’ or a ‘‘Y-connector.’’

These also can be found at most computer stores. If you are in a hurry to get started,

you probably can unplug the power connector from your 5.25" floppy drive (if you

#1 To Pin #1

Either end of the cable may be

connected to either the CD-ROM

drive or to the SCSI interface board

Pin #1

CHAPTER 8 ---- Hardware Installation

28 PX-43CH/PX-45CH OPERATION MANUAL

haveone) andplugit intoyourCD-ROM drive.Youwill beable to useyour CD-ROM

drive until you have the opportunity to buy a ‘‘splitter’’ or ‘‘Y-connector.’’ (Of course,

you will lose the use of your 5.25" drive until you buy a splitter/Y-connector.)

If your computer has only a 3.5" floppy disk drive, you may find that you do not have

a power connector that is the correct size to plug into your CD-ROM drive. Once

again, you can turn to your local computer store for a splitter to solve this problem,

or you might find an adapter that converts the smaller sized power plug found on a

3.5" drive to the size required for your CD-ROM drive.

A third cable, an audio cable, must be used if there is a soundboard in your system.

This cable runs from the four pin audio output connector on the rear panel of your

drive to your soundboard. See page 33 for more information about audio cables.

Installation of your internal drive is now complete. Skip to page 32.

External Drive Installation

YOUR TASK: Connect cables from your external drive to your PC

or Mac. Check to see if switch, dial and terminator

settings need to be adjusted.

YOUR OBJECTIVE: A well functioning drive that does not conflict with

any other peripherals in your computer system.

YOUR METHOD: Follow directions below for making cable

connections. Review your current computer set-up

to see if the potential for conflicts exist. If so, make

necessary switch, dial and/or terminator changes.

IfyouareinstallingasinglePX-45CH,andyouhavenootherSCSIperipheralsattached

to your system, you should leave the switches, dial and terminator found on the rear

panel of your drive at their factory settings. If you do have additional SCSI peripherals

(e.g., scanner, printer) attached to your computer, you may need to change your

switch, dial and terminator settings. See Chapter 6 and 7 for information on how to

change these settings.

If you are installing a single PX-45CH external drive, connect it as shown on the next

page:

CHAPTER 8 ---- Hardware Installation

PX-43CH/PX-45CH OPERATION MANUAL 29

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Plextor Lecteur CD/CDR

Plextor

Plextor PX-W4012TA Manuel utilisateur

Plextor

Plextor 8PL-3 Manuel utilisateur

Plextor

Plextor 4PS-C Manuel utilisateur

Plextor

Plextor PL-6P2 Manuel utilisateur

Plextor

Plextor 12X-2 Manuel

Plextor

Plextor PX-W1610TA Manuel utilisateur

Plextor

Plextor PX-W2410TU Manuel utilisateur

Plextor

Plextor PX-S2410TU Manuel utilisateur

Plextor

Plextor PL-6P3 Manuel utilisateur

Plextor

Plextor PX-W12432TSe Manuel utilisateur

Plextor

Plextor PX-W2410TA Manuel utilisateur

Plextor

Plextor PX-W4012TSe Manuel utilisateur

Plextor

Plextor 12-20D Manuel utilisateur

Plextor

Plextor PlexWriter PX-230A Manuel utilisateur

Plextor

Plextor 12X-3 Mode d’emploi

Plextor

Plextor PX-20TSe Manuel utilisateur

Plextor

Plextor PX-43CE Manuel utilisateur

Plextor

Plextor 12-20C Mode d’emploi

Plextor

Plextor PX-W4012TU Manuel utilisateur

Plextor

Plextor 8PL-4 Manuel utilisateur

Plextor

Plextor PX-W8220Te Manuel utilisateur

Plextor

Plextor PX-W5224TA Manuel utilisateur

Plextor

Plextor 412-3 Mode d’emploi

Plextor

Plextor 4PS-3 Manuel utilisateur

Manuels Lecteur CD/CDR populaires d'autres marques

Philips

Philips CDD3610 Manuel utilisateur

QPS

QPS Que!Fire Manuel utilisateur

LG GCC-4241N Manuel utilisateur

Samsung

Samsung SN-324B Manuel utilisateur

Teac

Teac CD-211E Manuel utilisateur

SmartDisk

SmartDisk Firewire CD-R/W Manuel utilisateur

Axis

Axis CD-ROM SERVER Manuel utilisateur

LG CRD-8322B Manuel utilisateur

Memorex

Memorex 32023234 - 52x32x52x External USB2.0 CD... Instructions d'installation

Yamaha

Yamaha CD Recordable/Rewritable Drive CRW3200 Manuel utilisateur

Sony

Sony CRX230AE Manuel utilisateur

Sony

Sony CRX - 160E Manuel utilisateur

Panasonic

Panasonic KX-LD742 Manuel utilisateur

Pioneer

Pioneer BDR-S13U-X Manuel utilisateur

Panasonic

Panasonic LK-MC606BP Manuel utilisateur

Panasonic

Panasonic CF-VCW Series Manuel utilisateur

LG CRD-8320B Manuel utilisateur

Conner

Conner CFP2107 Series Manuel utilisateur