Playcore DERO Arc Rack Manuel utilisateur
©2021
Arc Rack Setbacks
36"
36"
42"
STREET
WALL
©2021
Installation Surface MountArc Rack
RECOMMENDED BASE MATERIAL
Solid concrete is the best base material for installation. To ensure the proper anchors
are shipped with your rack, ask your Dero Rack representative which anchor is
appropriate for your application. Be sure nothing is underneath the base material that
could be damaged by drilling.
TOOLS NEEDED
Tape Measure
Marker or Pencil
Masonry Drill Bit 3/8”
Drill (Hammer drill recommended)
Hammer
Wrench 9/16”
Level
Drill 3/8” diameter holes 3” deep into surface. Make sure the
holes are at least 3” away from any cracks in the base material.
Thread nuts onto anchors, leaving approximately 1/4” of the
anchor protruding, and tap into surface. Tighten nuts down to
secure rack.
Place the rack in the desired location. Use a marker or pencil to
outline the holes of the flange onto the base material.
Place rack (and washers to level rack if necessary) over holes.
1
3
2
4
Ø 3/8”
9/16”
3”
©2021
Installation In-Ground Mount : New ConcreteArc Rack
TOOLS NEEDED
Level
Cement mixing tub
Shovel
Pour concrete and allow to cure.
An easy way to brace the Arc Rack while the grout sets is to bolt
two 1x4” boards together at one end and clamp them onto the
legs of the Arc Rack like a clothes pin.
Place corrosion resistant sleeve (min. 4” inside diameter) in sand
pour bed in exact location where rack will be installed. Make
sure top of sleeve is at same level as desired finished concrete
surface. Fill sleeve with sand to keep it in place and prevent it
from filling with concrete.
After appropriate cure time, dig out sand from sleeves and insert
racks, making sure they are level and at the appropriate height.
Pour in Super Por-Rok or epoxy grout and allow to set.
1
3
2
Trowel
Corrosion-Resistant Sleeve (min. 4” diameter)
Materials to build brace (see “Install Tip” at bottom of page)
Sand pour bed
Sleeves
Final grade level
Poured concrete
(4-7” deep)
TIP
©2021
Installation In-Ground Mount : Existing ConcreteArc Rack
TOOLS NEEDED
Level
Cement mixing tub
Shovel
Access to water hose
Fill holes with Super Por-Rok or epoxy grout.
An easy way to brace the Arc Rack while the grout sets is to bolt
two 1x4” boards together at one end and clamp them onto the
legs of the Arc Rack like a clothes pin.
Core holes no less than 6” diameter and no less than 11” deep
into sidewalk.
Place Arc Rack into holes, making sure the rack is level until the
grout has set. The welds at the base should be just bellow the
surface.
1
3
2
Trowel
Hole coring machine with 6” bit
Materials to build brace (see “Install Tip” at bottom of page)
TIP
Ø 6” min.
11” min.
©2021
Installation Footing DiagramsArc Rack
12”
36”
10”
18”
24”
IN-GROUND MOUNT SURFACE MOUNT
(or standard 4” sidewalk slab)
Table des matières
Autres manuels Playcore Support et étagère
Playcore
Playcore Colorado Time Systems F1057 Manuel utilisateur
Playcore
Playcore DERO BIKER BAR Manuel utilisateur
Playcore
Playcore DERO Cycle Dock Manuel utilisateur
Playcore
Playcore DERO Round Rack Manuel utilisateur
Playcore
Playcore DERO Bike Manuel utilisateur
Playcore
Playcore DERO BIKE DEPOT Manuel utilisateur
Manuels Support et étagère populaires d'autres marques
Salamander
Salamander Acadia AC/W/L400/WH Manuel utilisateur
Fohhn
Fohhn VAT-09 Guide de l'utilisateur
ricoo
ricoo FS0522 Manuel utilisateur
AMSOIL
AMSOIL BMK-22 Guide rapide
Kargo Master
Kargo Master 48220 Manuel utilisateur
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur
