Planet WNRT-625 Instructions de montage
802.11n Wireless Broadband Router
WNRT-625
Quick Installation Guide
Table of Contents
Introduction ................................................................................... 3
Package Content............................................................................. 4
Hardware Installation ...................................................................... 5
Web Conguration .......................................................................... 8
Further Conguration .....................................................................11
3
Introduction
Thank you for purchasing PLANET 802.11n Wireless Broadband Router,
WNRT-625. In this Quick Installation Guide, it illustrates the hardware
installation and the basic conguration.
4
Package Content
1 x WNRT-625
1 x Ethernet Cable
1 x Power Adapter
1 x CD Disk
1 x Quick Installation Guide
Note
If any of the above items are missing or damaged,
contact your local dealer for support.
l
l
l
l
l
5
Hardware Installation
1. Locate an optimum location for the WNRT-625. The best place
for your WNRT-625 is usually at the center of your wireless network,
with line of sight to all of your mobile stations.
2.
Adjust the antennas of WNRT-625. Try to adjust them to a posi-
tion that can best cover your wireless network. The antenna’s posi-
tion will enhance the receiving sensitivity.
3.
Connect xDSL/Cable Modem to WAN port of WNRT-625.
Usually, this cable would be provided with your modem. If no cable
was supplied with your modem, please use a RJ-45 Ethernet cable
4. Connect all of your network devices to LAN port of WNRT-
625. Connect all your computers, network devices (network-enabled
consumer devices other than computers, like game console, or switch
/ hub).Connect one of the LAN ports on WNRT-625 to your LAN
switch/hub or a computer with a RJ-45 cable.
6
5. Plug in power adapter and connect to power source. After
power on, WNRT-625 will start to operate.
6. Please check all LEDs on the front panel. ‘PWR’ LED should
be steadily on. WAN and LAN LEDs should be on if the computer
/ network device connected to the respective port of the router is
powered on and correctly connected. If PWD LED is not on, or any
LED you expected is not on, please recheck the cabling, or jump to
‘Troubleshooting’ on manual for possible reasons and solution.
Other outlook interface:
Radio ON/
OFF
Enable/disable wireless signal button.
** In case switching wireless signal via “Radio ON/
OFF” button to “OFF” situation, the functions of
wireless settings on web UI will be unavailable.
7
RST / WPS
Button
This button has two functions:
1. To Clear All Data and restore the factory
default values:
Press the RST (reset) button for longer than 20
seconds until the LED of power ash, and then
the router will reset itself to the factory default
settings.
(Warning: your original congurations will be
replaced with the factory default settings)
2. To make Wi-Fi Protected Setup (WPS)
simple and easier:
Press the WPS button (for less than 3 seconds);
machine will start WPS function to build
connection between wireless network clients and
this wireless router.
8
Web Conguration
WNRT-625 provides a user friendly interface for users to congure it
via web browser. Please follow the steps below to congure WNRT-625
basic settings.
1. Open your web browser and type WNRT-625 default IP address
(http://192.168.0.1) into the “Address Field” of you web browser.
Before conguration, please make sure your PC’s IP address is under
the same IP range with WNRT-625.
2. After enter the IP address and press Enter key, you can see the
dialog box appear as below, please enter the User name and Pass-
word with “admin”. Then press “OK”.
3. Please click “Quick Setup” on the left panel to setup your WNRT-625.
9
4. Select a Time Zone that corresponds to your country. Time Zone
setting will affect functions such as Log entries and Firewall. You may
keep the default Time Server address or set a new Time Server’s IP
address for WNRT-625 to adjust it’s time on the Internet. Please click
“Next” to continue.
5. The WNRT-625 supports six Internet connection types. This informa-
tion must be provided by your local ISP.
6. The IP Address Info page appears after you choose suitable Broad-
band Type. Different Broadband Type will have different IP settings.
You must obtain all necessary information from your local ISP and
enter the correct parameters in this page.
10
7. Click “Apply” to save the settings.
8. Please wait for 30 seconds for WNRT-625 restart. Then click “OK”.
Autres manuels pour WNRT-625
5
Table des matières
Autres manuels Planet Routeur sans fil
Planet
Planet WDAP-8350 Manuel utilisateur
Planet
Planet VDR-300NU Manuel utilisateur
Planet
Planet WDRT-1200AC Manuel utilisateur
Planet
Planet WDRT-750AC Manuel utilisateur
Planet
Planet WNAP-6300 Manuel utilisateur
Planet
Planet WRT-416 Manuel utilisateur
Planet
Planet Pre-N Wireless Router WNRT-610 Manuel utilisateur
Planet
Planet WNRT-625G Manuel utilisateur
Planet
Planet XRT-411 Manuel utilisateur
Planet
Planet WNRT-625 Manuel utilisateur
Planet
Planet WRT-416 Manuel utilisateur
Planet
Planet VDR-301n Manuel utilisateur
Planet
Planet WRT-414 Manuel utilisateur
Planet
Planet WNAP-6335 Manuel utilisateur
Planet
Planet WNRT-625 Manuel utilisateur
Planet
Planet ADN-4100 Manuel utilisateur
Planet
Planet WNRT-625 Manuel utilisateur
Planet
Planet WNAP-6315 Manuel utilisateur
Planet
Planet VRT-401 Manuel utilisateur
Planet
Planet WNRT-626G Manuel utilisateur
