Planet WAP-4030 Manuel utilisateur

Wireless Access Point

WAP-4030

User s Manual

be reproduced, transmitted, transcribed, stored in aretrieval system, or translated into any language

or computer language,in any form or by any means, electronic, mechanical,magnetic, optical,

chemical, manual or otherwise, without the prior written permission of PLANET.

PLANETmakes no representations or warranties, either expressed orimplied,with respectto the

contentshereof and specifically disclaims any warranties, merchantability or fitness for any particular

purpose.Any software described in this manual is sold or licensed "as is". Should the programs prove

defective following theirpurchase, the buyer (and not PLANET,itsdistributor,or itsdealer)assumes

the entirecostofall necessary servicing,repair,and any incidental or consequential damages

resulting from any defectin the software. Further,PLANETreserves the right torevise this publication

and tomake changes from time to time in the contentshereof without obligation to notify any person of

such revision or changes.

All brand and productnames mentioned in this manual are trademarks and/orregistered trademarks

of their respective holders.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limitsfor aClass Bdigital device,

pursuant toPart15 of FCC Rules. These limitsare designed to provide reasonable protection against

harmful interference in aresidential installation. This equipment generates, uses, and can radiate

radio frequency energy and, ifnot installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However,thereis no guarantee that interference will not

occur in aparticular installation. If this equipment does cause harmful interference toradio ortelevision

reception, which can be determined by turning the equipment off and on, the useris encouraged to try

to correctthe interference by one or more of the following measures:

1. Reorientor relocate the receiving antenna.

2. Increase the separation between the equipmentand receiver.

3. Connect the equipmentinto an outlet on acircuit different from that towhich the receiveris

connected.

4. Consult the dealer or an experienced radio technician forhelp.

FCC Caution

Toassurecontinued compliance. (example-use only shielded interface cables when connecting to

computeror peripheral devices). Any changes or modifications not expressly approved by the party

responsible for compliance could void the user s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the Following two

conditions: (1) This device may not cause harmful interference, and (2)this Device must accept any

interference received, including interference thatmay cause undesired operation.

Federal Communication Commission (FCC) Radiation Exposure

Statement

This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In

order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity

to the antenna shall not be less than 20 cm (8 inches)during normal operation.

R&TTE Compliance Statement

This equipmentcomplies with all the requirementsof DIRECTIVE 1999/5/CE OF THE EUROPEAN

PARLIAMENT AND THE COUNCILOF 9March 1999 on radio equipment and telecommunication

terminal Equipment and the mutual recognition of theirconformity (R&TTE)

The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal

Equipmentand Satellite EarthStation Equipment) As of April 8,2000.

Safety

This equipment is designed withthe utmost care for the safetyof those who install and use it. However,

special attention must be paid to the dangersof electric shock and static electricity when working with

electrical equipment.All guidelines ofthis and ofthe computer manufacture mustthereforebe allowed

at all times to ensure the safe use of the equipment.

EU Countries Not Intended for Use

The ETSI version of this device is intended forhome and office use in Austria Belgium,Denmark,

Finland,France (with Frequency channel restrictions). Germany,Greece, Ireland, Italy,

Luxembourg .The Netherlands, Portugal, Spain, Sweden and United Kingdom.

The ETSI version ofthis device is also authorized foruse in EFTAmember states Iceland,

Liechtenstein, Norway and Switzerland.

Potential restrictive use

France: Only channels 10,11,12 and 13

Revision

User s Manual for PLANET Wireless Access Point

Model: WAP-4030

Rev: 1.0 (July, 2004)

Part No. EM-WAP4030

TABLE OF CONTENTS

Chapter 1 Introduction 1

1.1 Package Contents1

1.2 System Requirements1

1.3 Features1

1.4 Specification 2

1.5 Wireless Performance 3

Chapter 2 Hardware Installation4

2.1 Hardware Connection 4

Chapter 3 Configuring theWirelessAP5

3.1 Association Table5

3.2 Radio Setting6

3.3 Security7

3.4 IPConfig 9

3.5 Filter List 10

3.6 Firmware Upgrade 12

Chapter 4 Troubleshooting 13

Chapter 1 Introduction

Thank you for purchasing WAP-4030.This device is an access point for IEEE 802.11g 2.4GHz wireless

network. You can use this access point tobuild up awireless LAN, any wireless LAN station can join the

wireless network. It supports64/128-bit WEP (Wired Equivalent Privacy) Encryption, WPA-PSK and MAC

address filter function to consolidate the wireless network security; you can prevent unauthorized

wireless stations from accessing your wireless network. Withthe detachable antenna design, users can

install a high gain antenna for better network link quality and wider coverage.

1.1 Package Contents

Make sure that you have the following items:

· 1 x WAP-4030

· 1 xAC Power Adapter

· 1 xUser s Manual CD

· 1 xQuick Installation Guide

· 1 xDipole Antenna

Note:

If any of the above items are missing, contact your supplier as soon as

possible.

1.2 System Requirements

Before installation, please check the following requirementswith your equipment.

· Pentium Based (And Above) IBM-Compatible PC System

· CD-ROMdrive

· Windows 98/Me/NT/2000/XP/Server2003 Operating System with TCP/IP protocol

1.3 Features

l Compliant with the IEEE 802.11g/802.11b (DSSS) 2.4GHz specification

l High data rate up to 54Mbps, Auto rate fallback

l Seamlessly integrate wireless and wired EthernetLAN networks

l Provide WPA-PSK, 64/128-bit WEPEncryption and MAC Filter to protect the wireless data

transmissions

l Support DHCP clientfor auto IP addresses assignment

l Provides a reverse-polaritySMAconnector forexternal antenna connection

l Auto Fall-Back Data Rate for Long-Distance communication and noisy environment

l Support 63 clients to connect the network. (For best performance, the suggested

maximum clients number of one WAP-4030 is 25)

l Web-based configuration

1.4 Specification

StandardIEEE 802.11g /802.11b

Frequency Band 2.400~2.4835GHz

Transfer Rate 802.11g: 54/48/36/24/18/12/9/6Mbps

802.11b: 11/5.5/2/1Mbps

Modulation OFDM, CCK, DQPSK and DBPSK

Sensitivity IEEE802.11b:

-92dBm @ 1Mbps

-89dBm @ 2Mbps

-87dBm @ 5.5Mbps

-82dBm @ 11Mbps

IEEE802.11g

-91dBm @ 6Mbps

-90dBm @ 9Mbps

-87dBm @ 12Mbps

-82dBm @ 18Mbps

-82dBm @ 24Mbps

-78dBm @ 36Mbps

-71dBm @ 48Mbps

-71dBm @ 54Mbps

Channel FCC: 11 Channels (US, Canada)

ETSI: 13 Channels (Europe)

ELEC: 14 Channels (Japan)

Radio Technology

Direct Sequence Spread Spectrum (DSSS)

Antenna External detachable dipole antenna

Transmit Power 16±2dBm (Typical)

LAN Interface 1-port RJ-45 UTP

Cabling Category 5/5e or above, 4-pair

LED Indicators 3; PWR,WLAN,LAN

Power 12V DC, 0.5A

Temperature 0 ~ 55°C (Operating)

Humidity 10 ~ 90%, non-condensing (Operating)

Dimension 169 x87 x30 (mm)

Weight 155g

Emission FCC Class B, CE-mark

1.5 Wireless Performance

The following information will help you utilizing the wireless performance and operating coverage of

WAP-4030.

1. Site selection

Toavoid interferences, please locateWAP-4030 and wireless clientaway from transformers,

microwave ovens,heavy-duty motors, fluorescentlightsand other industrial equipments.Keep the

number of walls or ceilings between AP and clientsas few as possible. Otherwise the signal strength

may be seriously reduced. Place WAP-4030 in open space or add additional WAP-4030 as needed

to improve the coverage.

2. Environmental factors

The wireless network is easily affected by many environment factors. Every environmentis unique

with different obstacles, construction materials, weather,etc. It is hardto determine the exact

operation rage of WAP-4030 in a specific location without testing.

3. Antenna adjustment

The bundle antenna of WAP-4030 is adjustable. Firstly install the antenna pointing straight up, then

smoothly adjust it if the radio signal strength is poor.But the signal reception is definitelyweak is

some certain areas,such as location right down the antenna.

Moreover,the original antenna of WAP-4030 can be replaced with other external antennas toextend

the coverage. Please check the specification of the antenna you want to use, and make sure itcan

be used on WAP-4030.

4. WLAN Type

If WAP-4030 is installed in an 802.11b and 802.11g mixed WLAN, itsperformance will reduced

significantly.Because every 802.11g OFDMpacket needs tobe preceded by an RTS-CTS or CTS

packet exchange that can be recognized by legacy 802.11b devices.This additional overhead

lowers the speed. If there are no 802.11b devices connected, or if connections to all 802.11b devices

are denied so thatWAP-4030 can operatein 11g-only mode, then itsdatarate should actually

54Mbps.

Chapter 2 Hardware Installation

Before you proceed with the installation, it is necessary that you have enough information about the

WAP-4030.

2.1 Hardware Connection

12V DC

LAN RESETANT

1. Locate an optimum location for the WAP-4030. Thebestplace for your WAP-4030 is usually

at the center of your wireless network, with line of sight to all of your mobile stations.

2. Assemble the antennas to WAP-4030. Try to place them to aposition that can best cover your

wireless network. The antenna sposition will enhance the receiving sensitivity.

3. Connect RJ-45 cable to WAP-4030. Connect this WAP-4030 to your LAN switch/hub or a single

PC.

4. Plug in power adapter and connect topower source.After power on, WAP-4030 will start to

work.

Note: ONLYuse the power adapter supplied with the WAP-4030. Otherwise, the product may be

damaged.

If you want to reset your WAP-4030 to default settings, press the Reset button 5 second.

And then wait for 10 seconds for WAP-4030 restart.

Chapter 3 Configuring the WirelessAP

Web configuration provides auser-friendly graphical user interface (web pages)to manage your

WAP-4030.An AP with an assigned IPaddress (e.g. http://192.168.0.1)will allowyou to monitorand

configure via web browser (e.g., MS Internet Explorer or Netscape).

1. Open your web browser.

2. Enter WAP-4030 IP address (default IP address is http://192.168.0.1)intothe address field of the web

browser. Please also make sure your PC s IPaddress is in the same IP range with WAP-4030.

3. AUser name and Password dialog boxwill appear.Please enter your User name and Password here.

DefaultUser name and Password is “admin”. Click “OK”.

4. Then you will see the WAP-4030 configuration web pages.

3.1 Association Table

In this screen, you can see the MAC addresses of the clientsconnect to this Access Point.

3.2 Radio Setting

In this option, you can set the wireless settings such as SSIDand RF Channel tothis Access Point.

When configuration finished, please click “Apply”to save.

Table des matières

Autres manuels Planet Point d'accès sans fil

Planet

Planet WDAP-W7200AC Manuel utilisateur

Planet

Planet Network Device WAP5 Manuel utilisateur

Planet

Planet MAP-3120 Manuel utilisateur

Planet

Planet WDAP-C7200E Manuel utilisateur

Planet

Planet WAP-4036 Manuel utilisateur

Planet

Planet WAP-3000 Manuel utilisateur

Planet

Planet WDAP-2000PE Manuel utilisateur

Planet

Planet WDAP-C1750 Manuel utilisateur

Planet

Planet WAP-4060PE Manuel utilisateur

Planet

Planet Network Device WAP-5100 Manuel utilisateur

Planet

Planet WAP-2000 Manuel utilisateur

Planet

Planet WAP-252N Manuel utilisateur

Planet

Planet 802.11g Wireless Access Point / Bridge... Manuel utilisateur

Planet

Planet WNAP-6350 Manuel utilisateur

Planet

Planet WNAP-6350 Manuel utilisateur

Planet

Planet WAP-252N Manuel utilisateur

Planet

Planet WNAP-6305 Manuel utilisateur

Planet

Planet 802.11n Wireless Access Point WNAP-1120 Manuel utilisateur

Planet

Planet IAP-2000PS Manuel utilisateur

Planet

Planet WDAP-3000AX Manuel utilisateur

Planet

Planet IAP-1800AX Manuel utilisateur

Planet

Planet WBS-202N Manuel utilisateur

Planet

Planet WNAP-6305 Manuel utilisateur

Planet

Planet WDAP-1750AC Manuel utilisateur

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Cisco

Cisco Aironet 1550 Series Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

EnGenius

EnGenius EnStationACv2 Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur