Planet MGS-5220-8P2X Manuel utilisateur
L2+ Managed Multigigabit Switch
MGS-5220-8P2X
Quick Installation Guide
Table of Contents
1 Package Contents ....................................................................................... 3
2. Requirements ............................................................................................. 4
3. Terminal Setup ........................................................................................... 5
3.1 Logon to Console................................................................................. 6
3.2 ConguringIPAddress......................................................................... 6
3.3 Storecurrentswitchconguration......................................................... 8
4. Starting Web Management .......................................................................... 9
4.1 LoggingintotheManagedSwitch ........................................................ 9
4.2. SavingConguration...........................................................................13
5. RecoveringBacktoDefaultConguration.....................................................14
6. Customer Support .....................................................................................15
3
1 Package Contents
Thank you for purchasing PLANET MGS-5220-8P2X Managed PoE Switch. The
descriptionofthismodelisshownbelow:
MGS-5220-8P2X L2+8-Port2.5GBASE-T802.3atPoE+2-Port10GSFP+
ManagedMultigigabitSwitch
“Managed Switch” is used as an alternative name in this Quick Installation
Guide.
Open the box of the Managed Switch and carefully unpack it. The box should
containthefollowingitems:
zTheManagedMultigigabitPoESwitchx1
zQuickInstallationGuidex1
zRJ45 to RS232 Cable x 1
zRubberFeetx4
zTwoRack-mountingBracketswithAttachmentScrewsx1
zPowerCordx1
zSFPDust-proofCapsx2
If any item is found missing or damaged, please contact your local reseller for
replacement.
4
2. Requirements
zWorkstations running Windows 10/XP/2003/Vista/7/8/2008, MAC OS X or later,
Linux,UNIX,orotherplatformsarecompatiblewithTCP/IPprotocols.
zWorkstationsareinstalledwithEthernetNIC(NetworkInterfaceCard)
zSerialPortConnection(Terminal)
The above Workstations come with COM Port (DB9) or USB-to-RS232
converter.
The above Workstations have been installed with terminal emulator, such as
TeraTerm,PuTTYorHyperTerminalincludedinWindowsXP/2003.
Serial cable -- one end is attached to the RS232 serial port, while the other
endtotheconsoleportoftheManagedPoESwitch.
zEthernetPortConnection
Networkcables--Usestandardnetwork(UTP)cableswithRJ45connectors.
The above PC is installed with Web browser and JAVA runtime environment
plug-in.
Note
It is recommended to use Internet Explore 8.0 or above to access
the Managed Switch. If the Web interface of the Managed Switch
is not accessible, please turn off the anti-virus software or firewall
andthentryitagain.
5
3. Terminal Setup
To congure the system, connect a serial cable to a COM port on a PC or
notebookcomputerandtoRJ45typeofserialportoftheManagedSwitch.
Managed Switch
PC / Workstation
with
Terminal Emulation Software
Serial Port
RS232 to RJ45 Cable
Console Port
RJ45
Figure 3-1: Managed Switch Console Connectivity
A terminal program is required to make the software connection to the Managed
Switch.
1. Run terminal program on the OS.
2.When the following screen appears, make sure that the COM port should be
conguredas:
Baud:115200
Databits:8
Parity:None
Stopbits:1
Flowcontrol:None
Figure 3-2: COM Port Conguration
6
3.1 Logon to Console
Once the terminal is connected to the device, power on the Managed Switch, and
the terminal will display “running testing procedures”. Then, the following message
asks to log-in user name and password. The factory default user name and
passwordareshownasfollowsandtheloginscreeninFigure3-3appears.
Username:admin
Password:admin
Figure 3-3: Managed PoE Switch Console Login Screen
The user can now enter commands to manage the Managed Switch. For a detailed
descriptionofthecommands,pleaserefertothefollowingchapters.
Note
1.For security reason, please change and memorize the new pass-
wordafterthisfirstsetup.
2.Onlyacceptcommandinlowercaseletterunderconsoleinterface.
3.2 ConguringIPAddress
TheManagedPoESwitchisshippedwithdefaultIPaddressshownbelow.
IPAddress:192.168.0.100
SubnetMask:255.255.255.0
7
To check the current IP address or modify a new IP address for the Switch, please
usetheproceduresasfollows:
Show the current IP Address
1.Atthe“#”prompt,enter“show ip interface brief”.
2.ThescreendisplaysthecurrentIPaddressasshowninFigure3-4.
Figure 3-4: IP Information Screen
ConguringIPAddress
3.At the “#” prompt, enter the following command and press <Enter> as shown
inFigure3-5.
MGS-5220-8P2X#congureterminal
MGS-5220-8P2X(cong)#interfacevlan1
MGS-5220-8P2X(cong-if-vlan)#ip address 192.168.1.100 255.255.255.0
ThepreviouscommandwouldapplythefollowingsettingsfortheManagedSwitch.
IP Address: 192.168.1.100
Subnet Mask: 255.255.255.0
Figure 3-5: Conguring IP Address Screen
8
4.Repeatstep1tocheckiftheIPaddresshaschanged.
If the IP is successfully congured, the Managed Switch will apply the new IP
address setting immediately. You can access the Web interface of the Managed
SwitchthroughthenewIPaddress.
3.3 Storecurrentswitchconguration
In the Managed Switch, the running conguration sequence running-cong can
be saved from the RAM to FLASH by “copy” command, so that the running
conguration sequence becomes the start-up conguration le, which is called
congurationsave.
Atthe“#”prompt,enterthefollowingcommandandpress<Enter>.
#copyrunning-congstartup-cong
Figure 3-6: Saving Current Conguration Command Screen
Note
If you are not familiar with the console command or the related
parameter, enter “help” anytime in console to get the help
description.
9
4. Starting Web Management
The following shows how to start up the Web Management of the Managed
Switch. Note the Managed Switch is congured through an Ethernet connection.
Please make sure the manager PC must be set to the same IP subnet address.
For example, the default IP address of the Managed Switch is 192.168.0.100,
then the manager PC should be set to 192.168.0.x (where x is a number
between1and254,except100),andthedefaultsubnetmaskis255.255.255.0.
PC / Workstation with Web Browser
192.168.0.x
Managed Switch
RJ45/UTP Cable
IP Address: 192.168.0.100
Figure 4-1: IP Management Diagram
4.1 Logging in to the Managed Switch
1.Use Internet Explorer 8.0 or above Web browser and enter IP address
http://192.168.0.100(thefactorydefaultIPaddressortheonethatyouhave
justchangedinconsole)toaccesstheWebinterface.
2.When the following dialog box appears, please enter the default user name and
password “admin” (or the password you have changed via console). The login
screeninFigure4-2appears.
DefaultIPAddress:192.168.0.100
DefaultUsername:admin
DefaultPassword:admin
Figure 4-2: Login Screen
10
3.Afterenteringthepassword,themainscreenappearsasFigure4-3shows.
Figure 4-3: Web Main Screen of Managed Switch
The Switch Menu on the top of the Web page lets you access all the commands
and statistics the Managed Switch provides. The Switch Menu includes System,
Switching,QoS,Maintenance,SecurityandPoE.
Figure 4-4: Switch Menu
Figure 4-5: Switch Menu -- System
Table des matières
Autres manuels Planet Changer
Planet
Planet KVM-210 M Series Manuel utilisateur
Planet
Planet WGSW-2403 Manuel utilisateur
Planet
Planet GS-5220-16S8C Manuel utilisateur
Planet
Planet POE-1200G Manuel utilisateur
Planet
Planet MGSW-24160F Manuel utilisateur
Planet
Planet FNSW-2402S Manuel utilisateur
Planet
Planet GSD-800S Manuel utilisateur
Planet
Planet UPOE-1600G Manuel utilisateur
Planet
Planet FGSW-008 Manuel utilisateur
Planet
Planet GSW-1600HP Manuel utilisateur
Planet
Planet DH-1600 Manuel utilisateur
Planet
Planet IGS-4215-16P2T2S Manuel utilisateur
Planet
Planet XGS3-24042 Manuel utilisateur
Planet
Planet WGSD-910 Manuel utilisateur
Planet
Planet GS-4210-24T4S Manuel utilisateur
Planet
Planet NOVASwitch FNSW-8086F Manuel utilisateur
Planet
Planet TSN-6325-8T4S4X Manuel utilisateur
Planet
Planet IGS-6325-16P4S Manuel utilisateur
Planet
Planet IKVM-8020 Manuel utilisateur
Planet
Planet GSD-804P Manuel utilisateur
