Planet IGSW-24040T Manuel utilisateur
Industrial L2+
20-Port 10/100/1000T + 4-Port TP/SFP Combo
Managed Ethernet Switch
IGSW-24040T
Quick Installation Guide
Table of Contents
1. Package Contents ....................................................................................... 3
2. Requirements ............................................................................................. 4
3. Wiring DC Power Inputs .............................................................................. 5
4. Terminal Setup ........................................................................................... 6
4.1 Logging on to Console ......................................................................... 7
4.2 ConguringIPAddressviaConsole ....................................................... 8
5. Starting Web Management .........................................................................10
5.1 LoggingintotheIndustrialManagedSwitch.........................................11
5.2 SavingCongurationviaWeb ..............................................................14
6. RecoveringBacktoDefaultConguration.....................................................15
7. Customer Support .....................................................................................16
3
1. Package Contents
Thank you for purchasing PLANET Industrial L2+ Managed Ethernet Switch.
“Industrial Managed Switch” is used as an alternative name in this Quick
InstallationGuide.
Open the box of the Industrial Managed Switch and carefully unpack it. The box
shouldcontainthefollowingitems:
TheIndustrialManagedSwitch x 1
QuickInstallationGuide x 1
DB9toRJ45ConsoleCable x 1
Rubber Feet x 4
RackMountAccessoryKit x 1
ACPowerCord x 1
SFP Dust Cap x 4
RJ45DustCap x 25
If any item is found missing or damaged, please contact your local reseller for
replacement.
4
2. Requirements
zWorkstations running Windows XP/2003/2008/2012/Vista/7/8/10/11, MAC OS X
orlater,Linux,UNIX,orotherplatformsarecompatiblewithTCP/IPprotocols.
zWorkstationsareinstalledwithEthernetNIC(NetworkInterfaceCard).
zSerialPortConnection(Terminal)
The above Workstations come with COM Port (DB9) or USB-to-RS232
converter.
The above Workstations have been installed with terminal emulator, such as
HyperTerminalincludedinWindowsXP/2003,puttyorteraterm.
Serial cable -- one end is attached to the RS232 serial port, while the other
endtotheconsoleportoftheIndustrialManagedSwitch.
zEthernetPortConnection
Networkcables--Usestandardnetwork(UTP)cableswithRJ45connectors.
Note
It is recommended to use Chrome 98.0.xxx or above to access the
Industrial Managed Switch. If the Web interface of the Industrial
Managed Switch is not accessible, please turn off the anti-virus
softwareorfirewallandthentryitagain.
5
3. Wiring DC Power Inputs
The 6-contact terminal block connector on the front panel of the Industrial
ManagedSwitchis usedfortwo DCredundantpower input.Pleasefollow thesteps
below to insert the power wires.
1.Insert positive/negative DC power wires into contacts 1 and 2 for DC Power 1,
or5and6forDCPower2.
RingRing
AlarmAlarm I/OI/O
ACAC
DC1DC1
R.O.R.O.DC2DC2
AlarmAlarmDC1 DC2
DC POWER
ON
OFF
DC Input:
36-60V
, 0.7A max.
100- 240V
~,
0.5A max.
50/60 HzOFF
ON
AC POWER
GNDGNDDO 1DO 0DI 1DI 0
Max. Fault Alarm Loading: 24V, 1A
2.Tightenthewire-clampscrewsforpreventingthewiresfromloosening.
1 2 3 4 5 6
V1+ V1- V2+ V2-
Power 1 Power 2
Positive(+)Pin Negative(-)Pin
IGSW-24040T Pin1/5 Pin2/6
Note
The wire gauge for the terminal block should be in the range
between12and24AWG.
6
4. Terminal Setup
To congure the system, connect a serial cable to a COM port on a PC or
notebook computer and to RJ45 type of serial port of the Industrial Managed
Switch.
Managed Switch
PC / Workstation
with
Terminal Emulation Software
Serial Port
RS232 to RJ45 Cable
Console Port
RJ45
Figure 4-1: Industrial Managed Switch Console Connectivity
A terminal program is required to make the software connection to the Industrial
ManagedSwitch.
1. Run terminal program on the OS.
2.When the following screen appears, make sure that the COM port should be
conguredas:
Baud:115200
Databits:8
Parity:None
Stopbits:1
Flowcontrol:None
Figure 4-2: COM Port Conguration
7
4.1 Logging on to Console
Once the terminal is connected to the device, power on the Industrial Managed
Switchandtheterminalwilldisplay“runningtestingprocedures”.
Then, the following message asks to log in user name and password. The factory
default user name and password are shown as follows and the login screen in
Figure4-3appears.
Username:admin
Password:admin
Figure 4-3: Industrial Managed Switch Console Login Screen
The user can now enter commands to manage the Industrial Managed Switch. For
adetaileddescriptionofthecommands,pleaserefertothefollowingchapters.
Note
1.For security reason, please change and memorize the new
passwordafterthisfirstsetup.
2.Only accept command in lowercase letter under console
interface.
8
4.2 ConguringIPAddressviaConsole
TheIndustrialManagedSwitchisshippedwithdefaultIPaddressshownbelow.
IPAddress:192.168.0.100
SubnetMask:255.255.255.0
To check the current IP address or modify a new IP address for the Switch, please
usetheproceduresasfollows:
DisplayingthecurrentIPAddress
1.Atthe“#”prompt,enter“show ip interface brief”.
2.ThescreendisplaysthecurrentIPaddressasshowninFigure4-4.
Figure 4-4: IP Information Screen
ConguringIPAddress
3.At the “#” prompt, enter the following command and press <Enter> as shown
inFigure4-5.
IGSW-24040T# congure terminal
IGSW-24040T(cong)# interface vlan 1
IGSW-24040T(cong-if-vlan)# ip address 192.168.1.100 255.255.255.0
9
The previous command would apply the following settings for the Industrial
ManagedSwitch.
IPAddress:192.168.1.100
SubnetMask:255.255.255.0
Figure 4-5: Conguring IP Address Screen
4.RepeatStep1tocheckiftheIPaddresshaschanged.
Storingcurrentswitchconguration
5.Atthe“#”prompt,enterthefollowingcommandandpress<Enter>.
# copy running-cong startup-cong
Figure 4-6: Saving Current Conguration Command Screen
If the IP is successfully congured, the Industrial Managed Switch will apply the
new IP address setting immediately. You can access the Web interface of the
IndustrialManagedSwitchthroughthenewIPaddress.
Note
If you are not familiar with the console command or the related
parameter, enter “help” anytime in console to get the help
description.
10
5. Starting Web Management
The following shows how to start up the Web Management of the Industrial
Managed Switch. Note the Industrial Managed Switch is congured through an
Ethernet connection. Please make sure the manager PC must be set to the same
IP subnet address.
For example, the default IP address of the Industrial Managed Switch is
192.168.0.100, then the manager PC should be set to 192.168.0.x (where x
is a number between 1 and 254, except 100), and the default subnet mask is
255.255.255.0.
PC / Workstation
with Web Browser
192.168.0.x
Managed Switch
RJ45/UTP Cable
IP Address: 192.168.0.100
Figure 5-1: IP Management Diagram
Autres manuels pour IGSW-24040T
2
Table des matières
Autres manuels Planet Changer
Planet
Planet GSD-805 Manuel utilisateur
Planet
Planet WGSW-20160HP Manuel utilisateur
Planet
Planet FGSW-2620CS Manuel utilisateur
Planet
Planet MGS-5220-8P2X Manuel utilisateur
Planet
Planet WGSW-2620HP Manuel utilisateur
Planet
Planet SGS-6341-24T4X Manuel utilisateur
Planet
Planet WGSW-24000 Manuel utilisateur
Planet
Planet GSD-800 Manuel utilisateur
Planet
Planet ISW-1022MT Manuel utilisateur
Planet
Planet HPOE-460 Manuel utilisateur
Planet
Planet ISW-504PS Manuel utilisateur
Planet
Planet IKVM-8020 Manuel utilisateur
Planet
Planet MGSD-10080F Manuel utilisateur
Planet
Planet WGS-5225-8MT Manuel utilisateur
Planet
Planet IGS-4215-4P4T Manuel utilisateur
Planet
Planet HPOE-1200G Manuel utilisateur
Planet
Planet WGSW-2840 Manuel utilisateur
Planet
Planet WGs-4215-8HP2S Manuel utilisateur
Planet
Planet GSD-808HP Manuel utilisateur
Planet
Planet IGS-5225-8P4S-12V Manuel utilisateur
