Planet FT-807 Manuel utilisateur

Trademarks

Contents subject to which revision without prior notice.

PLANET is a registered trademark of PLANET Technology Corp.

All other trademarks belong to their respective owners.

Disclaimer

PLANET Technology does not warrant that the hardware will work

properly in all environments and applications, and makes no

warranty and representation, either implied or expressed, with

respect to the quality, performance, merchantability, or ﬁtness for

a particular purpose.

PLANET has made every effort to ensure that this User’s Manual

is accurate; PLANET disclaims liability for any inaccuracies or

omissions that may have occurred.

Information in this User’s Manual is subject to change without

notice and does not represent a commitment on the part of

PLANET. PLANET assumes no responsibility for any inaccuracies

that may be contained in this User’s Manual. PLANET makes no

commitment to update or keep current the information in this

User’s Manual, and reserves the right to make improvements to

this User’s Manual and/or to the products described in this User’s

Manual, at any time without notice.

If you ﬁnd information in this manual that is incorrect, misleading,

or incomplete, we would appreciate your comments and

suggestions.

FCC Warning

This equipment has been tested and found to comply with the

limits for a Class A digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in

a commercial environment. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and used

in accordance with the Instruction manual, may cause harmful

interference to radio communications. Operation of this equipment

in a residential area is likely to cause harmful interference in which

case the user will be required to correct the interference at whose

own expense.

CE Mark Warning

This is a Class A product. In a domestic environment, this product

may cause radio interference, in which case the user may be

required to take adequate measures.

WEEE Warning

To avoid the potential effects on the environment and

human health as a result of the presence of hazardous

substances in electrical and electronic equipment, end

users of electrical and electronic equipment should

understand the meaning of the crossed-out wheeled

bin symbol. Do not dispose of WEEE as unsorted

municipal waste and have to collect such WEEE

separately.

Revision

PLANET Fast Ethernet Converter User’s Manual

FOR MODEL: FT-807

Rev: 1.1(December, 2005)

Part No. 2010-AA3331-000

Table of Contents

Chapter 1 Introduction

1.1 Product Description 1

1.2 Packet Contents 1

1.3 Technical Specification 1

1.4 Product Outlook 2

1.5 Duplex Mode Setting 3

1.6 Power information 3

Chapter 2 Installation 3

APPENDIX A: RJ-45

pin assignment and cable system 5

A. 1 10/100Mbps, 10/100Base-TX 5

A. 2 100Mbps, 100Base-FX, SMI type connector 5

This page is intentionally left blank

Chapter 1

Introduction

The PLANET FT-807 is a 10/100Base-TX shielded twisted pair

(STP) to Fast Ethernet 100Base-FX ﬁber converter. It supports

full-duplex operations at its ﬁber-optic interface in the form factor

of SMI (Small Multimedia Interface) interface. The converter

auto-adapts to the highest level of performance supported by the

device connected to the STP port.

1.1 Product Description

The SMI (small multimedia interface) is one kind of POF (plastic

optic ﬁber) interface that can suitable for low-cost and high-speed

data transmission. The SMI patch cord meets the IEEE 1394b

speciﬁcation that can transmit data at S200 (250Mbps) speed for

50 meters, the distance range of TP port is 100 meters. It will

make the new generation multimedia life more possible and easy

installation.

1.2 Packet Contents

Your FT-807 carton should contain following items:

 The Fast Ethernet Media Converter.

 AC to DC Power Adapter (Output: 5V DC, 2A max).

 This User’s Manual.

If any item is found missing or damaged, please contact your local

reseller from whom you purchased your Fast Ethernet Converter.

1.3 Technical Speciﬁcation

Standard IEEE 802.3u, 10/100Base-TX and

100Base-FX

TP Connector RJ-45 port (Auto-MDI/MDI-X) Twisted

Pair, EIA568

Fiber Con-

nector

SMI POF port (multi-mode), 650nm

wavelength

Data Rate

10/100Mbps (TP) ; Auto-Negotiation for

duplex mode

100Mbps (FX) ; full-duplex mode

TP Cable 4 pair Cat. 3 or 5 UTP, up to 100m

Fiber Cable IEEE 1394b SMI Patch cord (0.98mm

/1mm), up to 50m

LED indicators PWR, TP. POF

Dimensions 86 x 62 x 23 mm (W x D x H)

Power Re-

quirement 5V DC, 2A

1.4 Product Outlook

LED Deﬁnition

POF: Lights to indicate the SMI connection is established.

TP: Lights to indicate the TP connection is established.

PWR: Lights to indicate the converter is powered.

1.5 Duplex Mode Setting

The TP port of FT-807 supports duplex mode detection by auto-

negotiation (A-N). The following is the duplex mode parameters:

Fast Ethernet Device FT-807 Duplex Mode Sup-

port

Ethernet/Fast Ethernet

Hub Half-Duplex

Ethernet / Fast Ethernet

Switch (without A-N) Half-Duplex

Fast Ethernet Devices *

Support Auto-Negotiation Full-Duplex/Half Duplex

NOTE:

Normally, an A-N switch will detect and set to

full-duplex, where a dual-speed hub will detects

half.

The ﬁber port (POF) port of FT-807 is ﬁxed at 100Mbps full-duplex

mode. The link partner should also set at 100Mbps full-duplex

mode at the same time.

1.6 Power information

The power jack of FT-807 is with 2.5mm in the central post

and required +5VDC power input. Should you have the issue to

make the power connection, please contact with your local sales

representative.

Chapter 2 Installation

Please follow these steps to install the converter:

 Turn off the power of the device/station in a network to

which the FT-807 will be attached.

 Ensure that there is no activity in the network.

 Attach POF fiber cable with SMI type connector from the

FT-807 to the fiber network also using POF.

 Attach a Cat. 5 UTP cable from the 10/100Base-TX net-

work to the RJ-45 port on the FT-807.

 Connect the 5VDC power adapter to the FT-807 and

verify that the Power LED lights up.

 Turn on the power of the device/station, the TP and POF

LED should light when all cables are attached.

NOTE:

1. RJ-45/STP, UTP Cat 5, straight/cross-

over cable is accepted.

2. Please note the FT-807 supports LFP

function, both ends should well con-

nected. Otherwise, both TP and fiber

port will remains off if any of the port is

not connected.

3. Consult for your network administrator

for more information about POF net-

work equipments. Usually, another FT-

807 is required for pair installation and

transmission.

Warning:

As an optical equipment, to reduce the risk

of injury to the eyes, do not look directly into

the laser light on the POF interface and do not

point the laser light into anyone’s eyes in short

distance.

APPENDEX A

Appendix A: RJ-45 pin assignment and

cable system

A.1 10/100Mbps, 10/100Base-TX

When connecting your 10/100Mbps Ethernet Switch to another

switch, a bridge or a hub, a straight or crossover cable is

necessary. Each port of the Switch supports auto-MDI/MDI-X

detection. That means you can directly connect the Switch to any

Ethernet devices without making a crossover cable. The following

table and diagram show the standard RJ-45 receptacle/ connector

and their pin assignments:

RJ-45 Connector pin assignment

Con-

tact

MDI

Media Dependant

Interface

MDI-X

Media Dependant

Interface -Cross

1 Tx + (transmit) Rx + (receive)

2 Tx - (transmit) Rx - (receive)

3 Rx + (receive) Tx + (transmit)

4, 5 Not used

6 Rx - (receive) Tx - (transmit)

7, 8 Not used

The standard cable, RJ-45 pin assignment

The standard RJ-45 receptacle/connector

There are 8 wires on a standard UTP/STP cable and each wire is

color-coded. The following shows the pin allocation and color of

straight cable and crossover cable connection:

Figure A-1: Straight-Through and Crossover Cable

Please make sure your connected cables are with same pin

assignment and color as above picture before deploying the cables

into your network.

A.2 100Mbps, 100Base-FX, SMI type connector

FT-807 is using POF SMI type connector that is mostly being

used for IEEE1394 transmission. The followings show the basic

information.

The POF Cable should be a dual wire cable with

0.98mm optic core with cladding diameter 1mm.

Also with jacket in diameter: 2.2 mm.

The SMI connector will as like the ﬁgure

left. You can check with your network

device dealer or administrator for the

availability of the cable and connector.

Autres manuels pour FT-807

Table des matières

Autres manuels Planet Convertisseur de média

Planet

Planet IGTP-802T Manuel utilisateur

Planet

Planet XT-900 Series Manuel utilisateur

Planet

Planet ICS-100 Manuel utilisateur

Planet

Planet WFT-801 Manuel utilisateur

Planet

Planet IFT-802 Manuel utilisateur

Planet

Planet SMART MEDIA CONVERTER GST-70X Manuel utilisateur

Planet

Planet vc-231 Manuel utilisateur

Planet

Planet ICS-10 Series Manuel utilisateur

Planet

Planet IGUP-1205AT Manuel utilisateur

Planet

Planet GT-1205A Manuel utilisateur

Planet

Planet VC-102M Manuel utilisateur

Planet

Planet FT-802S Manuel utilisateur

Planet

Planet GT-80X Series Manuel utilisateur

Planet

Planet Media Converter Chassis MC-1000R Manuel utilisateur

Planet

Planet GT-902 Manuel utilisateur

Planet

Planet FT-722 Manuel utilisateur

Planet

Planet GEPON EPL-SPT-8 Manuel utilisateur

Planet

Planet EM-GT70X Manuel utilisateur

Planet

Planet ICS-2100 Manuel utilisateur

Planet

Planet POE-165S Manuel utilisateur

Planet

Planet vc-234 vdsl2 Manuel utilisateur

Planet

Planet ET-508 Manuel utilisateur

Planet

Planet GST-702/702S Manuel utilisateur

Planet

Planet FST-801 Manuel utilisateur

Manuels Convertisseur de média populaires d'autres marques

SoundTraxx

SoundTraxx Blunami BLU-2200 Manuel utilisateur

SPROLINK

SPROLINK VA1 Manuel utilisateur

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manuel utilisateur

Nikon

Nikon AF-S TC-20E III Manuel utilisateur

Axis

Axis AXIS Q7406 Manuel utilisateur

Omega

Omega TAC80B-J Manuel utilisateur

Zoom

Zoom Thunderbolt TAC-2R Manuel utilisateur

OST

OST iConverter 10/100M Manuel utilisateur

Vertiv

Vertiv Netsure Manuel utilisateur

birddog

birddog MINI Manuel utilisateur

Roland

Roland GI-10 Manuel utilisateur

Wallenstein

Wallenstein WX310 Manuel utilisateur

Pace

Pace MSS 200-1 Manuel utilisateur

Solar Converters

Solar Converters EQ 12/24-50 Manuel utilisateur

CYP

CYP EL-7400V Manuel utilisateur

TIE

TIE MIDI 1i1o Manuel utilisateur

DCS

DCS Vivaldi Upsampler Manuel utilisateur

Westermo

Westermo MCW-211 SERIES Manuel utilisateur