Planet FT-701B Manuel utilisateur

Contents subject to revision without prior notice.

PLANET is a registered trademark of PLANET Technol-

ogy Corp. The information in this manual is subject to

change without notice. All other trademarks belong to

their respective owners.

Disclaimer

PLANET Technology does not warrant that the hardware

will work properly in all environments and applications,

and makes no warranty and representation, either

implied or expressed, with respect to the quality, per-

formance, merchantability, or tness for a particular

purpose.

PLANET has made every effort to ensure that this User‘s

Manual is accurate; PLANET disclaims liability for any

inaccuracies or omissions that may have occurred.

Information in this User’s Manual is subject to change

without notice and does not represent a commitment on

the part of PLANET. PLANET assumes no responsibility

for any inaccuracies that may be contained in this User‘s

Manual. PLANET makes no commitment to update or

keep current the information in this User’s Manual, and

reserves the right to make improvements to this User‘s

Manual and/or to the products described in this User’s

Manual, at any time without notice. If you nd infor-

mation in this manual that is incorrect, misleading, or

incomplete, we would appreciate your comments and

suggestions.

FCC Warning

This equipment has been tested and found to comply

with the regulations for a Class A digital device, pur-

suant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against

harmful interference when the equipment is operated in

a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not

installed and used in accordance with this user’s guide,

may cause harmful interference to radio communica-

tions. Operation of this equipment in a residential area

is likely to cause harmful interference, in which case the

user will be required to correct the interference at his

own expense.

CE Mark Warning

This is a Class A product. In a domestic environment,

this product may cause radio interference, in which case

the user may be required to take adequate measures.

Revision

User’s manual for PLANET Fast Ethernet Converter

Multi-mode: FT-701B, FT-702B, FT-703, FT-704

Single-mode: FT-702S15, FT-702S35, FT-702S50,

FT-703S, FT-706A15, FT-706B15

Rev 4.0 (July 2004)

Part No. 2010-000001-003

Table of Contents

Chapter 1 Overview 1

Chapter 2 Model List 1

Chapter 3 Checklist 2

Chapter 4 Product Outlook 2

Chapter 5 Installing the Converter 3

Chapter 6 Duplex Mode Setting 5

Chapter 7 The LED Indications 6

Chapter 8 Cable Connection Parameter 7

Chapter 9 Technical Specifications 8

Chapter 10 Power information 9

Chapter 1

Overview

Thank you for purchasing PLANET FT-70X family Fast Ethernet

Twisted pair to Fiber-optic Converter. This converter is used to

convert one type media signal to other type equivalent that allows

two type segments connect easily, efciently and inexpensively.

This converter can be used as a standalone unit or as a slide-in

module to the 10 /19 media chassis (up to 15 units) for a TP

and Fiber combined networks at a central wiring closet. Please

contact with your sales representative for more about the 19

media chassis.

Chapter 2

Model List

Your Fast Ethernet Converter comes with one of the following

models.

ð FT-701B on board ST fiber connector

ð FT-702B/S on board SC fiber connector

ð FT-703/S on board MT-RJ fiber connector

ð FT-704/S on board VF-45 fiber connector

ð FT-706A15 on board single SC fiber connector

ð FT-706B15 on board single SC fiber connector

Models with last two numbered characters indicates the ber-

port is with Single-Mode optic ber connector and the number

indicates the maximum distance in km. The rest will be Multi-

Mode optic ber models.

In the following sections, the term FT-70X indicates the product

family above.

Chapter 3

Checklist

Your FT-70X carton should contain the following items:

ð The Fast Ethernet Converter

ð AC-DC Power Adapter (Output: 5VDC, 2 A max.)

ð This user’s manual

If any item is missing or damaged, please consult the dealer from

whom you purchased your Fast Ethernet Converter.

Chapter 4

Product Outlook

Right View (FT-70X)

There are one RJ-45 Twisted-Pair jack, one ber-optic connector

and six LED indicators on this side.

The ber connector is different from model to model. Please refer

to the section 2 Model List and section 9 Technical Specication

for detail.

Left View (FT-70X)

One DC jack for DC power input.

Side View (FT-70X)

One DIP Switch for TP Device selection.

Chapter 5

Installing the Converter

Please follow these steps to install the converter:

• Turn off the power of the device/station in a network to

which the FT-70X will be attached.

• Ensure that there is no activity in the network.

• Attach fiber cable from the FT-70X to the fiber network.

TX, RX must be paired at both ends for some two con-

nectors models.

• Attach a Cat. 5 UTP cable from the 100Base-TX network

to the RJ-45 port on the FT-70X.

• Connect the 5VDC power adapter to the FT-70X and

verify that the Power LED lights up.

• Turn on the power of the device/station, the TX Link and

FX Link LEDs should light when all cables are attached.

 NOTE:

• RJ-45/STP, UTP Cat 5, straight-through

cable is accepted.

• Cabling from FT-70X TP port to a TP de-

vice is as below:

• To Workstation: DIP switch on DTE

• To Hub/Switch: DIP switch on MPR

• Please refer to section 8 for more about

the wiring distance of your TP, Optic-fiber

networks.

• Please note FT-706A15/706B15 is de-

signed to work together. It means you

must connect FT-706A15 to FT-706B15

from them to work normally. If both ends

are FT-706A15 or FT-706B15, they can’t

work normally and may damage the fiber

connectors.

Chapter 6

Duplex Mode Setting

The twisted pair port of FT-70X support duplex mode selection

by Auto-Negotiation (A-N). The following is the duplex mode

parameters:

Fast Ethernet Device FT-70X Duplex Mode support

Fast Ethernet Hub Half-Duplex

Fast Ethernet Switch

(without A-N) Half-Duplex

Fast Ethernet Devices *

Support Auto-Negotiation Full-Duplex / Half-Duplex

 NOTE:

Normally, an A-N switch will be detected and

set to Full-duplex where a dual-speed hub

will be detected and set to Half-Duplex.

Chapter 7

The LED Indications

LED Color Status Description

TP ACT Green

Blinks

If fiber-optic is not present

for converter self-diagnose /

detecting

Blinks If both ports link with any TP

packets transmitting

OFF Fiber-optic link is present

OFF

With no TP/FX LINK on, i.e.

only turn on the power and

the ACT do not blink at all,

please consult your local

dealer

TP Link Green ON TP connection is good

FX ACT Green Blinks When any FX packets

transmitting

FX Link Green ON When Fiber connection is

good

FDX* Green ON When Full-duplex mode is

detected in TP port

PWR Green ON When +5VDC power

detected

 NOTE:

Fiber-optic partner should be set to the correct

mode according to this FDX indicator for optimal

network performance.

Chapter 8

Cable Connection Parameter

The cable distance limitations are as below:

Duplex Connection Limitation (max.)

Twisted Pair

Half / Full Node to Node

Node to Switch/Hub 100 meters

Multi-Mode Converters

MM Half* Node to Node

Node to Switch 412 meters

MM Full Node to Node

Node to Switch 2 kilometers

Single-Mode Converters (FT-70xS, FT-706A15/706B15)

SM Full Node to Node

Node to Switch

FT-70xS15: 15 km

FT-70xS35: 35 km

FT-70xS50: 50 km

FT-706A15: 15 km

FT-706B15: 15 km

 NOTE:

If the ber port works on half duplex, please

note that Fast Ethernet/100Base-TX network

allows 512 bit-time delay between any two

nodes/stations in a collision domain (when work

in half duplex). The overall bit time of TP/Fiber

wires and devices must below 512 bit-time in

one network segment. To extend the distance,

however, you may use switch to break up a

collision domain and extend the distance.

Autres manuels pour FT-701B

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Planet Convertisseur de média

Planet

Planet IXT-705AT Manuel utilisateur

Planet

Planet SMART MEDIA CONVERTER GST-70X Manuel utilisateur

Planet

Planet GT-80X Series Manuel utilisateur

Planet

Planet GT-1205A Manuel utilisateur

Planet

Planet GT-902 Manuel utilisateur

Planet

Planet WGT-702 Manuel utilisateur

Planet

Planet IGUP-805AT Manuel utilisateur

Planet

Planet GT-902 Manuel utilisateur

Planet

Planet GEPON EPL-SPT-8 Manuel utilisateur

Planet

Planet GT-702 Manuel utilisateur

Planet

Planet GT-922 Manuel utilisateur

Planet

Planet VC-201A Manuel utilisateur

Planet

Planet POE-151 Manuel utilisateur

Planet

Planet POE-173S Manuel utilisateur

Planet

Planet XT-900 Series Manuel utilisateur

Planet

Planet FT-1105A Manuel utilisateur

Planet

Planet IGT-900 Series Manuel utilisateur

Planet

Planet ICS-2100 Manuel utilisateur

Planet

Planet Ethernet Over VDSL Converter EV-401M Manuel utilisateur

Planet

Planet FT-807 Manuel utilisateur

Planet

Planet vc-231 Manuel utilisateur

Planet

Planet VC-231G Manuel utilisateur

Planet

Planet FT-90X FT-902 Manuel utilisateur

Planet

Planet POE-161S Manuel utilisateur

Manuels Convertisseur de média populaires d'autres marques

SoundTraxx

SoundTraxx Blunami BLU-2200 Manuel utilisateur

SPROLINK

SPROLINK VA1 Manuel utilisateur

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manuel utilisateur

Nikon

Nikon AF-S TC-20E III Manuel utilisateur

Axis

Axis AXIS Q7406 Manuel utilisateur

Omega

Omega TAC80B-J Manuel utilisateur

Zoom

Zoom Thunderbolt TAC-2R Manuel utilisateur

OST

OST iConverter 10/100M Manuel utilisateur

Vertiv

Vertiv Netsure Manuel utilisateur

birddog

birddog MINI Manuel utilisateur

Roland

Roland GI-10 Manuel utilisateur

Wallenstein

Wallenstein WX310 Manuel utilisateur

Pace

Pace MSS 200-1 Manuel utilisateur

Solar Converters

Solar Converters EQ 12/24-50 Manuel utilisateur

CYP

CYP EL-7400V Manuel utilisateur

TIE

TIE MIDI 1i1o Manuel utilisateur

DCS

DCS Vivaldi Upsampler Manuel utilisateur

Westermo

Westermo MCW-211 SERIES Manuel utilisateur