Planet Halo PH2s Manuel utilisateur
1.2
• Thank you for purchasing our product. The following is our product warranty
information, and keep this manual for future reference.
• Please read these safety instructions completely before operating this product.
• This product is a device for recording driving images and is supposed to be installed
inside of your motor vehicle to record front, inside and side scenes (4ch.). The product
is designed to help a driver to drive safely and the purpose of the audio and video
recordings is to help collecting evidence of accidents, but has no legal validity.
• The purpose of this product is to record surroundings of your motor vehicle when
you are driving or parking, but this does not guarantee that the product is able to
record everything while operating.
• This product might not be able to detect a mild impact or a minor collision and
cannot recorded under ‘event’ while you are driving or parking. We recommend you to
store event data by pressing the ‘event’ button to convert your current situation to
event situation.
• We cannot guarantee any product defects if you have used other kinds of storage
medium than our designated ones during the warrant period.
1. Product Information
▶This product is a device for recording high-resolution video, designed to monitor driving behavior and
capture incidents that could occur while your vehicle is on the road or parked. The recorded evidence may
or may not hold any legal validity in the court of law. Bear in mind that we are not responsible for any
disputes or loss in the court from recorded or unrecorded video data. Be safe, drive safe!
Instructions Before Operating this Product
1. Product Information
Before implementing the device, record on to a SD card for 5 to 10 minutes as a trial recording then check to
make sure that it recorded properly.
Using other type of power source than the one that is supplied will void the product warranty. Please note that
alternative power sources could cause a fire and damage the product.
Consult an installations expert if you intend on using direct power connection to the vehicle’s battery. The
product warranty will be void in the event of an installation mishap by a non-authorized dealer.
The warranty does not cover claims related to mishandling, tampering and / or disassembling of the product.
Altering and disassembling of the product may result in a fire or electric shock. Disassembling the product will
void the warranty. Inquire with your associate in the event the product needs repair work or a checkup.
Do not store the product in extreme high or low weather conditions. Exposure to sunlight for a long period of
time could cause the product to malfunction.
Refrain from using liquid cleaners or chemicals to clean the device. Using a cloth to wipe down the product will
suffice.
Product warranty will be void if you use an SD card other than the one supplied or recommended.
Saving files other than the device’s recorded files on to the SD card, may cause a camera error.
Do not use the SD card with other applicable products such as a portable navigation system or a digital
camera, as this may cause an error to the already existing recorded files.
Do not remove the SD card from its slot until after the power has been completely turned off, as this will
damage the camera.
Removing the SD card prior to all the LED lights shutting off may not save the last recorded file.
Do not try to change the settings of the product while driving, as it may cause a fatal accident.
Stop operating the product immediately if you notice smoke or burning smell, as it may result in a fire or
electric shock. Please contact your local dealer or supplier.
Clean the area of the windshield prior to mounting the camera.
Please note that cold weather may temporarily weaken the strength of the adhesive.
The product is designed to be installed inside the vehicle. Any damage caused by placing the device outside
your vehicle, or damage due to misuse of the product will void the warranty.
For additional information regarding your warranty and after warranty servicing of your product, please contact
your dealer or supplier.
3
Warranty and Safeguards
Main body (unit integral holder)
(PH4)
Side camera (PH4) Product attaching slide User’s manual
SD memory card Cable holder Holder adhesive tape Direct power cable
Cigar plug power cable
AVI output cable
Extra SD memory card (8G / 16G / 32G / 64GB)
External HDD/SSD
WiFI dongle / adapter
1. Product Information
Optional accessories
Product At a Glance
1. Product Information
Model PH2s PH4
Channel 2 4
Camera (Front) 1/2.9”CMOS Digital 1/2.9”CMOS Digital
Camera Angle (Front/Inner/Side) 130/140/- 130/140/75
Recording Resolution (Front) 1280x720/24FPS 720x480/20FPS
Recording Resolution (Inner) 720x480/15FPS 720x480/15FPS
Recording Resolution (Side) -720x480/7.5FPS
Recording Format H.264 VBR (Variable Bit Rate) Recording
Recording Mode
Driving Driving
Parking Parking
Event Event
Video Out CVBS output (1V Vp-p 75ohm)
LCD Screen - -
GPS Built-in GPS
G-Sensor Built-in 11Bit 3 Axis (X, Y, Z axis), acceleration sensor
Memory Card SD memory card - SD/SDHC: 2GB~64GB support
Default Memory Card 32GB 32GB
Audio Recording Via built-in high-sensitivity microphone / PCM compression
Voice Notice Built-in high quality speaker for status notice (voice/buzzer)
Time Setting Automatic internal RTC time setting
Battery Protection Yes Yes
Exclusive PC Viewer Yes Yes
Android App Viewer Yes Yes
iOS App Viewer Coming soon
WiFi Yes Yes
External HDD/SDD Yes Yes
Power - rated voltage DC 12V~24V DC 12V~24V
Power - operating voltage DC 7V~28V DC 7V~28V
Power Consumption To be confirmed To be confirmed
Temperature Range - Operating -10℃~70℃-10℃~70℃
Temperature Range - Storage -30℃~80℃-30℃~80℃
Product specifications may change from above, in order to improve the overall quality of the product.
Specification
1) Select the installing position of the product and then attach the slider on the windscreen.
2) Adjust camera angle facing the front and insert the product on to the slider.
3) Place side and rear cameras on the appropriate position and connect the camera cables to
the camera input terminal by using extension cables.
4) Insert the SD card into the main body. (Ensure that the SD card is correctly inserted / you
will hear a click sound)
[Note : Using the SD memory card]
: Must insert or eject the SD card when both the product and the LED lights are turned off and
the LED light is turned off.
: The SD card contains both the Viewer program and the update program. Please save these
programs to your PC.
: Using either damaged or low-quality SD card may damage the recorded data and decrease
the speed of saved video playback.
: Please be aware of the fact that the SD card does not last forever, and it may wear out after
using it for a certain time. It also may cause an error of recordings. Try to conduct format and
run virus checking programs regularly to prevent malfunctions of the SD card. SD card
related problems are not under guarantee and the manufacturer or the supplier is not
responsible for your data loss or missing recordings.
: We recommend you to make back up files and save them to other medium of storage such
as your PC because your valuable data can be damaged from external power voltage.
: Do not put a heavy pressure on the SD card and never use a wet SD card.
5) Connect a cigar plug to the power terminal of the product.
6) Insert the cigar plug into the cigar socket of your vehicle.
7) Check the LED lamp.
8) Use cable holders to tidy up cables.
Prior to attaching the holder, please be aware that the cold weather,
condensation, and dust may cause product damage from falling.
1. Product Information
Installation
7
This product will start to record once it is connected with the car battery or when you turn on the engine via a
cigar plug connection. You can stop recording by unplug the direct power cable or pressing the power button of
the product (temporarily) or turning off the engine (cigar plug connection). Then, consequently, it saves the last
recording scenes and ends operating. If the product is directly connected with the car battery, it may restart
recording once it gets a certain voltage of the power from the car battery. If the voltage of your car battery goes
below a certain set point, it will turn off the product to prevent your car battery to go flat (Battery Protection
Mode).
If there is a lack of memory space of the SD card, it will overwrite the latest data on top of the existing data. For
instance, the oldest normal recording data will be deleted and the latest recording data will be saved. In case of
event recording data, it deletes the data depends on the importance and time frame of the data.
Note: GPS Satellite Reception
The GPS may lose reception in areas where high-rise buildings are present. Stop
at a location where your GPS can regain its reception, before proceeding again.
Extreme weather conditions may interfere with the GPS reception. The operating
temperature should remain between 0~50℃.
GPS may take longer to connect when turning on the product for the first time, or
if the product has not been used for more than 3 days.
1. Product Information
[Checking LED lamp signal]
• Power : Red light will be flashing on the PWR LED lamp during the reboot once the power is
supplied after turning the engine on. Red light will be turned on the PWR LED lamp once the
rebooting is completed. (If there is a problem with the battery, or the battery protection mode
is on, the PWR LED light will keep flashing)
• GPS : Green light will be flashing on the GPS LED lamp while receiving the GPS reception.
(The GPS LED light will be turned off after 10 seconds if the GPS reception is being cutoff)
• Video recording : Red light will be flashing on the REC LED lamp during video recording.
(The REC LED light will be flashing every 0.5 to 1 second during the driving mode and it will
be flashing every 2-3 seconds during the parking mode.)
• Event recording : Blue light will be appeared on the EVENT LED lamp during event
recording. (The EVENT LED light will be turned off if the event recording mode is off)
[with HDD/SSD connection – Checking LED lamp signal]
Blue light will be flashing on the EVENT LED lamp every 0.5 to 1 second if the backup device
such as HDD/SSD is connected and recording properly during the driving mode and it will be
flashing every 2-3 seconds during the parking mode.)
You must check the below lights (pointed by hand) are flashing. Otherwise, please
check the cable connection on both ends: camera and external HDD/SSD case.
1. Product Information
Status Check
• This product provides real time high-resolution recording and surveillance functions through
connecting 4 cameras (front, internal, left and right). It starts to record after when you connect
the unit with a cigar plug and turn on the engine. The product stops recording after you turn
off the engine or turn off the power of the unit : consequently, it saves the last recording
scenes and ends operating. If it lacks memory capacity of the SD card, it overwrites the latest
data on top of existing data, erases the oldest normal recording data, and creates new
recording files. In case of event recording data, it erases the data depends on the importance
and time frame of the data.
1. Product Information
[Product button functions]
• Power button
: Pressing the ‘power’ button for 3-4 seconds, then it will turn on/off the product.
• Audio button
: Press ‘audio’ button to turn on/off audio recording mode.
• Parking button
: If you press on the ‘parking’ button once, the recording mode will be changed to the parking
mode.
*Pressing the ‘parking’ button for 3-4 seconds, then it will turn on/off the audio.
: If you press the ‘parking’ button once more, then it will change back to the normal recording
mode.
Parking mode is a function which you can record for a longer period than the normal
recording by reducing recording frames. The parking mode records 3 frames per second
If you set ‘0’ (do not use) for the parking mode in the configuration, then it will not
change the recording mode even you press the ‘parking’ button.
• Emergency button
: This function enables you to store data for a longer period than the normal recording by
creating an ‘event’ occurrence while stopping or parking.
: If you press the ‘event’ button from the time of accident, it will record pre-and-post events
for a few seconds. This means that you can store data for a longer period than the normal
recording. It will delete the most outdated event data in consecutive order once the event
recordings exceed its storing capacity.
: This button also does screen rotation which allows you to switch the displaying screen
mode; full(1ch.), 2ch. and quad when you see the playback via video out device
[4 channel high-resolution video image]
: The product is able to record clear and sharp video images by processing rapidly changing
video occurrences (VBR) as its top priority.
[Recording 4 different directions simultaneously: front, internal, left and right]
: Easy to install cameras without having space restraints.
[Simultaneous playback mode : full, 2ch. and 4ch. screen mode]
: Enable to divide playback screen into four to watch each cameras simultaneously.
[Automatic parking mode]
: Enable to setup (time frame) the parking mode from the setup menu of the Viewer program.
[Parking taillights function]
: It enables to prevent damage of your vehicle from a break in by using parking taillights
function in the night.
[Built-in GPS and high-sensitivity G-SENSOR]
: It enables to check the location (linked to Google maps), speed and acceleration information
at the time of recording on the Viewer program by using embedded GPS.
[Using database (db) that suits for the motor vehicle black box purpose]
: It minimizes deleting data from external data loss, and protects the user’s data by
recovering data loss.
[Extending the average life of the SD card by optimizing its expendability]
[Built-in protection function of a car battery]
: It prevents from discharging the battery by connecting the normal power from a car battery.
[External side and rear camera]
: Low power consumption design.
: Best quality resolution by using embedded deinterlace filter.
: Do not require to configure settings due to the Auto Mirror function.
1. Product Information
Key Functions and Features
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Planet Halo Caméra embarquée
