PLANEPRINT RISE nano Manuel de programmation
You can find the STL data
at www.planeprint.com
NOTE: Slicing only
works with CURA!
PRINTING & ASSEMBLING MANUAL
PRINTING & ASSEMBLING MANUAL
PRINTING & ASSEMBLING MANUAL
PRINTING & ASSEMBLING MANUAL
RISE NANO 2
PRINTING & ASSEMBLING MANUAL
© PLANEPRINT
PLALW-PLA TPU CARBON STEEL
RISE NANO 3
PRINTING & ASSEMBLING MANUAL
© PLANEPRINT
RC Components
ENGINE AXI 2203/40 VPP or comparable indoor-20 grams-motors.
31 mm
or comparable indoor-20 grams-motors.
PROP Aeronaut folding prop 6x3 or comparable, also possible 6x4, 7x3, 7x4
BEC-CONTROLLER 15 A (one matching the motor)
RECEIVER 3 Channel
BATTERY 2S Lipo, 350 MaH (ideal weight 24 to 27 grams)
SERVOS • Stemedu Micro 3.7g Servo GH-S37D
• PLANET-HOBBY ECO PLUS
• PICCO 8 DIGITAL SERVO
• Diamond D47
• Hitec HS 40 Eco Servo 4,8g
or similar in the same size, 2 pieces
There are also ready-made indoor drive sets with motor, servos and battery available from many dealers.
max. 22 mm max. 8.5 mm
max. 27 mm
Required accessoires – basic equipment
• LW-PLA (cannot be replaced by PLA!), ~100 grams
• PLA or Tough PLA, ~20 grams
• TPU A95, ~10 grams
• CA super glue (liquid and liquid medium)
• CA activator
• Steel wire Ø0.8*1000mm, 1 piece
• Carbon rod Ø4*1000mm, 1 piece
• Rod connection small, 2 pieces
• Neodym-Super-Magnet 5x5x5mm, 4 pieces
Tools
Cutter knife, Drill, small Philips screwdriver, Sandpaper,
Metal saw, Needle nose pliers
Rod connection hole 1 mm
RISE NANO
4
PRINTING & ASSEMBLING MANUAL
© PLANEPRINT
Printing the parts – Printing profiles
For the new PROFILE P5_Gyroid it is essential to use Cura Version 5 or later, It will work with
older versions, but the weight of the parts will be higher and the printing time longer.
This manual is constantly being improved and supplemented, we recommend downloading
the latest version from our website before building.
The development of a complex, airworthy RC flight model to express on any stan-
dard 3D printer is a very complex and extensive process. Therefore, we appeal to
your fairness not to forward the STL data you have acquired to third parties.
Thank you for your understanding and have fun with your PLANEPRINT MODEL!
Important for the
1-wall-print (P3, P5)!
In order to print airfoils of the lowest possi-
ble weight with high stability, it is necessa-
ry to print with only one wall line (Nozzle 0.4
mm). Decisive here is the adhesion between
the layers! To achieve this, you must print at
a much higher temperature than normal. As
a guideline, 230° C is a good starting point.
The parts-cooling fan should be set to 0% or
a maximum of 20%. Since not every printer
works the same, it may be necessary to make
small adjustments to these settings.
For slicing all Planeprint
models, these profiles have
to be created in Cura:
PROFILE P1_Fullbody
PROFILE P2_Hollowbody
PROFILE P3_Surface
PROFILE P4_Flex
PROFILE P5_Gyroid
You can find the description at
www.planeprint.com/print
PROFILE P5_Gyroid
It is essential for the necessary stability of the LW parts
printed with PROFILE_5 are as stable as possible. Please
use a test part to check the strength by fracture tests. It must
not break along the layer lines under any circumstances! Also
note that the printing temperature for LW-PLA is as low as
possible to obtain a wall thickness of 0.4 to 0.6 mm at a flow
of 60 to 70 % (depending on brand).
Caution: at too high temperatures, LW-PLA becomes brittle
and breaks more easily.
P1_Parts_Rn.stl
MATERIAL PLA, Weight: ~ 3 g
ADDITIONAL SETTINGS
None required
PROFILE P1_Fullbody PLA or Tough PLA
The following parts must be sliced with the PROFILE P1_Fullbody.
Please note the additional settings for the individual parts!
P1_Motormount-XXX_Rn.stl
MATERIAL PLA, Weight: ~ 1 g
ADDITIONAL SETTINGS
None required
RISE NANO 6
PRINTING & ASSEMBLING MANUAL
© PLANEPRINT
P1_Spinner folding prop Xmm_Rn.stl
MATERIAL PLA, Weight: ~ 1 g
ADDITIONAL SETTINGS
None required
PROFILE P1_Fullbody PLA or Tough PLA
The following parts must be sliced with the PROFILE P1_Fullbody.
Please note the additional settings for the individual parts!
P1_Protector_Rn.stl
MATERIAL PLA, Weight: ~ 3 g
ADDITIONAL SETTINGS
None required
RISE NANO 7
PRINTING & ASSEMBLING MANUAL
© PLANEPRINT
PROFILE P4_Flex TPU A95
The following parts must be sliced with the PROFILE P4_Flex.
Please note the additional settings for the individual parts!
P4_Hinges_Rn.stl
MATERIAL TPU ~ A95, Weight: ~ 1 g
ADDITIONAL SETTINGS
None required
RISE NANO 8
PRINTING & ASSEMBLING MANUAL
© PLANEPRINT
P5_Canopy_Rn.stl
MATERIAL LW-PLA, ~ 2 g*
*Weighed (approximate guideline)
ADDITIONAL SETTINGS
None required
P5_Elevator-L_Rn.stl and
P5_Elevator-R_Rn.stl
MATERIAL LW-PLA, ~ 2 g*
*Weighed (approximate guideline)
ADDITIONAL SETTINGS
None required
PROFILE P5_Gyroid Light-Weight LW-PLA!
The following parts must be sliced with the PROFILE P5_Gyroid. Please note the additional settings
for the individual parts! It is essential to print these parts with LW-PLA!
Basic settings for LW-PLA: Please follow the instructions in our WINGTEST AND CALIBRATION TOOL
on our website for correct adjustment!
RISE NANO 9
PRINTING & ASSEMBLING MANUAL
© PLANEPRINT
P5_Fuselage 1_Rn.stl
MATERIAL LW-PLA, ~ 6 g*
*Weighed (approximate guideline)
ADDITIONAL SETTINGS
None required
P5_Fuselage 2_Rn.stl
MATERIAL LW-PLA, ~ 7 g*
*Weighed (approximate guideline)
ADDITIONAL SETTINGS
None required
PROFILE P5_Gyroid Light-Weight LW-PLA!
The following parts must be sliced with the PROFILE P5_Gyroid. Please note the additional settings
for the individual parts! It is essential to print these parts with LW-PLA!
Basic settings for LW-PLA: Please follow the instructions in our WINGTEST AND CALIBRATION TOOL
on our website for correct adjustment!
RISE NANO 10
PRINTING & ASSEMBLING MANUAL
© PLANEPRINT
P5_V-Tail_Rn.stl
MATERIAL LW-PLA, ~ 8 g*
*Weighed (approximate guideline)
ADDITIONAL SETTINGS
• Z Seam Position: back left
P5_Wing 1-L_Rn.stl and
P5_Wing 1-R_Rn.stl
MATERIAL LW-PLA, ~ 20 g*
*Weighed (approximate guideline)
ADDITIONAL SETTINGS
None required
PROFILE P5_Gyroid Light-Weight LW-PLA!
The following parts must be sliced with the PROFILE P5_Gyroid. Please note the additional settings
for the individual parts! It is essential to print these parts with LW-PLA!
Basic settings for LW-PLA: Please follow the instructions in our WINGTEST AND CALIBRATION TOOL
on our website for correct adjustment!
Table des matières
