Pizzacraft PizzaQue PC7001 Manuel utilisateur

PizzaQue®

Pizzacraft®

PC7001

CS040215

©The Companion Group 2014

1250 9th Street, Berkeley, CA 94710

800-521-0505

[email protected]

IMPORTANT: This instruction manual contains important information necessary for the proper

assembly and safe use of the appliance.

Read and follow all warnings and instructions carefully before assembling and using the appliance. Keep this

manual for future reference.

Makes great tasting,

traditional Italian pizza –

with bubbly cheese, crispy

crust & toasty toppings.

OWNER’S MANUAL

Pizza Kit

for Kettle Grills

Safety Information .............................. 3

Assembly Instructions ....................... 4

Fitting Instructions ............................ 13

Lighting Instructions ......................... 16

Cooking Instructions......................... 17

Care and Maintenance....................... 18

Troubleshooting................................. 19

Replacement Parts ............................ 20

Accessories ....................................... 21

Warranty and Registration ................ 22

TABLE OF CONTENTS

SAFETY INFORMATION

IMPORTANT: Before you begin...

AS WITH ALL CHARCOAL GRILLS, THERE CAN BE SOME RISKS INVOLVED AND WE

WANT YOU TO STAY SAFE WHILE USING OUR PRODUCT.

1. Please read the following instructions and safety warnings completely before use. Keep this booklet for future

reference and feel free to contact us with any questions at 800-521-0505.

2. Always exercise caution when operating your kettle grill with the PizzaQue®Pizza Kit.

3. Your kettle grill with the PizzaQue®Pizza Kit will be HOT during and after cooking and should never be left

unattended while it is HOT.

4. Do NOT leave children, infants or pets unattended near your kettle grill with the PizzaQue®Pizza Kit while

it is still HOT.

5. Use in well-ventilated OUTDOOR areas only.

6. Use far away from combustible materials.

7. Do NOT remove ashes until charcoal is completely burned off.

8. When in use, access to a re extinguisher is highly recommended.

9. Intended for use with charcoal style kettle grills only.

10. Do NOT use in high winds. Use caution when wearing loose clothing while operating your kettle grill with

the PizzaQue®Pizza Kit.

11. Do NOT use other brand pizza stones in your kettle grill with the PizzaQue®Pizza Kit, as they may break

due to the high temperatures achieved by this kit.

12. Heat resistant gloves are highly recommended when handling your kettle grill with the PizzaQue®Pizza Kit

during and after use.

ASSEMBLY INSTRUCTIONS

Before beginning assembly of product, make sure all parts are present. Compare parts with package contents and hardware

contents list. Do not discard packing materials before assembly is complete.

If any part is missing or damaged, do not attempt to assemble the product. Call customer service at 800-521-0505.

To watch assembly video go to: www.pizzaque.com

Estimated assembly time: 30 minutes

Tools required - #2 Phillips screw driver and Crescent wrench (not included)

PACKAGE CONTENTS:

1. 15” pizza stone

2. Rear panel (for 22.5” grills ONLY)

3. Side panels (Qty 2)

4. Thermometer

5. Clips (Qty 5)

6. Wire door frame

7. Pizza stone supports (Qty 2)

8. Hardware package

9. Folding aluminum peel

10. Front support tabs (Qty 2 - for 18.5” grills ONLY)

11. Charcoal fence (Qty 4 x steel mesh panels)

HARDWARE PACKAGE CONTENTS:

1. (Qty 2) M5 x 15 screws -

2. (Qty 13) M5 x 8 screws

3. (Qty 15) M5 nuts

for side panel to door

frame connection

1. 2. 3.

2. 4.

11.

10.

screw placement

1. Insert short edges of wire door frame into channels on the front edge of the side panels (bottom edges of the wire door

frame and side panels should line up at -- shown in the SIDE VIEW below). Secure wire door frame to side panels by

inserting M5x15 phillips head screw through hole in side panel and side panel tab then tighten with M5 nut.

TOP VIEW

wire door frame

short edges

side panel channels

TOP VIEW

SIDE VIEW

Bottom edge of wire door frame

and side panels line up at

2. Attach rear panel to side panels. Make sure bottom edges of rear panel and side panels line up at and top edges align

at an angle. Secure tightly with M5x8 screws and M5 nuts. Check to conrm the bottom edge of the assembly sits at.

NOTE: One side edge of the rear panel lines up outside the side panel while the other lines up inside the side

panel.

rear panel on OUTSIDE

of left side panel

rear panel on INSIDE of

right side panel

TOP VIEW

rear panel shown in solid black

CONNECTION DETAIL

ASSEMBLY INSTRUCTIONS FOR 22.5 IN KETTLE GRILL

FRONT

at

angled

*ASSEMBLY INSTRUCTIONS FOR 18.5 IN KETTLE GRILL --> SKIP TO PAGE 10

3. Attach stone supports as shown (make sure that the tabs closer to the center of the pizza stone supports are face

up). Secure supports using M5x8 screws and M5 nuts.

Note the direction of the pizza stone support tabs

TOP VIEW

4. Attach thermometer by aligning probe and pins with designated holes in the (right) side panel. Secure with

thermometer probe nut.

FRONT

Make sure inner tabs are face

up for 22.5” kit setup

5b. WEBER 22.5” CLIP CONFIGURATION:

Attach side panel clips and rear panel clip (Qty 5 total -- 2 on each side panel and 1 on the rear panel). Clips near

front edge and clip in rear panel are mounted with the opening facing down, while the clips near the middle of

side panels are mounted with the opening facing up. Secure all clips with M5x8 screws and M5 nuts.

5a. MASTERBUILT PRO 22.5” CLIP CONFIGURATION:

Attach clip, with opening facing upward, to hole in center of rear panel. Then, attach 2 clips to side panels (1

on each side panel) so the opening of the clip is facing upward as shown below. Secure all 3 clips with M5x8

screws and M5 nuts.

Notice how individual clips are oriented

Pull rear clip all the way up

in slot and tighten securely

6. Construct charcoal fence. (1) Bend edge tab outward to expose u-channel and (2) slot at edge into u-channel

then (3) bend tab back over u-channel into original position to lock panels together. Repeat with all 4 panels of

the charcoal fence until you’ve create a completely enclosed shape. CAUTION: Wearing protective gloves is

strongly recommended when assembling the charcoal fence, as the edges may be sharp.

bend edge tab

outward

slot at edge

into u-channel

edge tab

u - channel

at edge

bend edge tab back inward to

original position to secure

(1)

(2)

(3)

COMPLETED 22.5” PIZZAQUE® PIZZA KIT ASSEMBLY. (Now go to step 7 for tting instructions)

Align top and bottom holes

on back edges of side panels

2. Rotate side panels toward each other until the holes on the back edge of both side panels line up (some force will be

needed). Use M5x8 screws and M5 nuts to secure the side panels together at back edge. NOTE: Rear panel will not be

needed for 18.5 in grill kit

ASSEMBLY INSTRUCTIONS FOR 18.5 IN KETTLE GRILL

3. Align attachment holes for pizza stone supports with designated side panel holes (make sure that the tabs closer to the

outer edge of the pizza stone supports are face up). Secure supports using M5x8 screws and M5 nuts.

Note the direction of the pizza stone support tabs

TOP VIEW

FRONT

Make sure outer tabs are face

up for 18.5” kit setup

Ce manuel convient aux modèles suivants

Table des matières

Manuels Gril populaires d'autres marques

Orbegozo

Orbegozo GR 2300 Manuel utilisateur

bora

bora PT11 Manuel utilisateur

Klarstein

Klarstein 10031664 Manuel utilisateur

Garland

Garland MWE3W Manuel utilisateur

Char-Broil

Char-Broil 463722714 Manuel utilisateur

Nexgrill

Nexgrill 720-0830HK Manuel utilisateur

Kenmore

Kenmore 415.16123800 Manuel utilisateur

Camp Chef

Camp Chef PG24CLAU Manuel utilisateur

Tucker Barbecues

Tucker Barbecues GTR Series Instructions de montage

Monogram

Monogram ZGG540NCP1SS Manuel utilisateur

Equipex

Equipex Sodir Savoy Manuel utilisateur

Gaggenau

Gaggenau VR 414 610 Manuel utilisateur

Miele

Miele KM 408-1 Manuel utilisateur

George Foreman

George Foreman GGR50B Manuel utilisateur

AOG

AOG T series Manuel utilisateur

Gorenje

Gorenje TG2000CB Mode d’emploi

Weber

Weber Genesis Silver-B Permamount NG 051701 Manuel utilisateur

Glen

Glen SA 3037 Manuel utilisateur