Pickering 60-850 Manuel utilisateur

pickeringtest.com

Issue 4.3 January 2020

60-850/851 User Manual

LXI Fiber Optic Multiplexer

Page (II) LXI FIBER OPTIC MULTIPLEXER 60-850/851

pickering

Page (II) REED RELAY MODULE 40-110/115/120/125

pickering

No part of this publication may be reproduced, transmitted, transcribed, translated or stored in any form, or by

any means without the written permission of Pickering Interfaces.

Technical details contained within this publication are subject to change without notice.

ISO 9001

Reg No. FM38792

Page (III)

LXI FIBER OPTIC MULTIPLEXER 60-850/851

pickering

Page (III)

REED RELAY MODULE 40-110/115/120/125

pickering

TECHNICAL SUPPORT

For Technical Support please contact Pickering Interfaces either by phone, the website or via e-mail.

WARRANTY

All products manufactured by Pickering Interfaces are warranted against defective materials and workmanship for a period of

three years, excluding programmable power supplies, from the date of delivery to the original purchaser. Any product found to be

defective within this period will, at the discretion of Pickering Interfaces be repaired or replaced.

Products serviced and repaired outside of the warranty period are warranted for ninety days.

Extended warranty and service are available. Please contact Pickering Interfaces by phone, the website or via e-mail.

ENVIRONMENTAL POLICY

Pickering Interfaces operates under an environmental management system similar to ISO 14001.

Pickering Interfaces strives to full all relevant environmental laws and regulations and reduce wastes and releases to the

environment. Pickering Interfaces aims to design and operate products in a way that protects the environment and the health and

safety of its employees, customers and the public. Pickering Interfaces endeavours to develop and manufacture products that can

be produced, distributed, used and recycled, or disposed of, in a safe and environmentally friendly manner.

Worldwide Technical Support and Product Information

pickeringtest.com

Germany

Tel: +49 89 125 953 160

E-mail: [email protected]

Sweden

Tel: +46 340-69 06 69

E-mail: [email protected]

USA

Tel: (West) +1 541 471 0700

Tel: (East) +1 781 897 1710

E-mail: [email protected]

Czech Republic

Tel: +420 558 987 613

E-mail: [email protected]

France

Tel +33 9 72 58 77 00

E-mail [email protected]

Pickering Interfaces Headquarters

Stephenson Road Clacton-on-Sea CO15 4NL United Kingdom

Tel: +44 (0)1255-687900

E-Mail: [email protected]

China

Tel: +86 4008 799 765

E-mail: [email protected]

Page (IV) LXI FIBER OPTIC MULTIPLEXER 60-850/851

pickering

MEANING / DESCRIPTION SYMBOL

PROTECTIVE EARTH (GROUND)

To identify any terminal which is intended for connection to an external conductor for

protection against electric shock in case of a fault, or the terminal of a protective earth

(ground) electrode.

DANGEROUS VOLTAGE

To indicate hazards arising from dangerous voltages.

WARNING / CAUTION

An appropriate safety instruction should be followed or caution to a potential hazard

exists.

Refer to the relevant instructions detailed within the product manual.

HEAVY

If this product is heavy and reference should be made to the safety instructions for

provisions of lifting and moving.

LASER PRODUCT

This product is capable of switching laser optical signals.

STATIC SENSITIVE

To indicate that static sensitive devices are present and handling precautions should

be followed.

SAFETY SYMBOLS

PRODUCT SAFETY

The following safety symbols may be used on the product and throughout the product documentation.

Page (V)

LXI FIBER OPTIC MULTIPLEXER 60-850/851

pickering

Technical Support and Warranty..................................................III

Product Safety .............................................................................. IV

Contents (this page)...................................................................... V

Warnings and Cautions .............................................................. VII

Section 1

Technical Specication...............................................................1.1

Section 2

Technical Description .................................................................2.1

Functional Description ....................................................2.1

Section 3

Installation....................................................................................3.1

Pre Operation Checks .....................................................3.1

Hardware Installation.......................................................3.1

Setting The IP Address ....................................................3.2

Installing The Software....................................................3.3

Soft Front Panel Operation .............................................3.3

Section 4

Programming Guide....................................................................4.1

Programming Options for LXI Units...............................4.1

Programming the 60-850 .................................................4.2

Command Line Control ...................................................4.6

Section 5

Connections.................................................................................5.1

Section 6

Trouble Shooting.........................................................................6.1

LXI Status Indicators .......................................................6.1

LAN Reset.........................................................................6.2

Section 7

Maintenance Information............................................................7.1

Optical Multiplexer Parts List .........................................7.2

General Maintenance.......................................................7.5

Section 8

Test Procedure.............................................................................8.1

Test Results ......................................................................8.2

Appendix A

Fitting Rack Mounting Flanges .................................................A.1

CONTENTS

Page (VI) LXI FIBER OPTIC MULTIPLEXER 60-850/851

pickering

THIS PAGE INTENTIONALLY BLANK

Page (VII)

LXI FIBER OPTIC MULTIPLEXER 60-850/851

pickering

WARNING - HAZARDOUS ENVIRONMENTS SYMBOL

This product is not specically designed for use in hazardous environments, for example in explosive

atmospheres. If the product is to be used in hazardous environments we recommend that the user

ensures suitable protective measures are taken.

WARNING - DANGER OF ELECTRIC SHOCK SYMBOL

This module may contain hazardous voltages. Before removing the module from the rack remove all

supplies and disconnect user I/O signals.

CAUTION - HANDLING OF ELECTROSTATIC-SENSITIVE DEVICES SYMBOL

Certain semiconductor devices used in this equipment are liable to damage due to static voltage.

Observe the following precautions when handling these devices in their unterminated state, or

sub-assemblies containing these devices:

1. Persons removing sub-assemblies from equipment using these devices must be earthed by a

wrist strap and a resistor at the point provided on the equipment.

2. Soldering irons used during the repair operations must be low voltage types with earthed tips and

isolated from the mains voltage by a double insulated transformer.

3. Outer clothing worn must be unable to generate static charges.

4. Printed Circuit Boards (PCBs) tted with these devices must be stored and transported in

anti-static bags.

CAUTION - PRODUCT DOCUMENTATION SYMBOL

Suitably qualied & trained users should ensure that the accompanying documentation is fully read

and understood before attempting to install or operate the product.

WARNING - RISK OF INJURY SYMBOL

This product is specically designed to switch optical signals. Under no circumstances look into the

end of an optical output or an optical cable attached to an optical output. LASER RADIATION CAN

SERIOUSLY DAMAGE YOUR EYESIGHT.

Read and understand the safety information of the laser source connected to the optical switch.

WARNINGS AND CAUTIONS

Page (VIII) LXI FIBER OPTIC MULTIPLEXER 60-850/851

pickering

SAFETY INSTRUCTIONS

All cleaning and servicing requires the equipment to be isolated and disconnected from the power source and user

I/O signals (refer to the Maintenance Section).

• Appropriate manual handling procedures should be followed as dictated by the weight of the individual module or

the combined weight of the modules & chassis.

• Should a fault occur with the module or chassis, immediately isolate and disconnect the incoming power to the

chassis and the user I/O signals.

• Ensure the equipment is installed, operated and maintained by trained and authorised personnel.

• Modules are not accessed to EN 60825, users should observe the safety instructions and laser

class for the 3rd party laser source.

• The module may be capable of switching optical signals from a laser device; do not stare directly

at the user I/O ports.

• For suitably equipped products in the event of an emergency press the red “emergency stop” button situated on

the front of the unit.

Page viii

LXI HIGH VOLTAGE 2-POLE MATRIX 60-310

pickering

CAUTION - PRODUCT DOCUMENTATION SYMBOL

Suitably qualied & trained users should ensure that the accompanying documentation is fully read

and understood before attempting to install or operate the product.

SAFETY INSTRUCTIONS

All cleaning and servicing requires the equipment to be isolated and disconnected from the power source and user I/O

signals (refer to the Maintenance Section).

• Appropriate manual handling procedures should be followed as dictated by the weight of the individual module or

the combined weight of the modules & chassis.

• Should a fault occur with the module or chassis, immediately isolate and disconnect the incoming power to the

chassis and the user I/O signals.

• Ensure the equipment is installed, operated and maintained by trained and authorised personnel.

• For suitably equipped products in the event of an emergency press the red “emergency stop” button situated on

the front of the unit.

WARNING - RACK MOUNTING

If it is required to t this unit into a 19 inch rack, its weight must be

supported by side brackets, runners or a suitable equipment shelf.

The xing holes in the front panel anges are designed only for

securing the device in the rack and must NOT be used to support

the weight of the whole device.

Please refer to Appendix A for the procedure for tting the

supplied anges to either side of the front panel.

HIGH VOLTAGE SAFETY WARNING

THIS UNIT IS CAPABLE OF SWITCHING VOLTAGES AND CURRENTS THAT CAN

CAUSE SERIOUS INJURIES. IN APPLICATIONS INVOLVING HIGH VOLTAGES IT

IS STRONGLY RECOMMENDED THAT UNUSED CONNECTORS ARE CAPPED

TO PREVENT ACCIDENTAL CONTACT WHILE IN USE. SYSTEM INTEGRATORS

AND USERS SHOULD CONNECT TO THE FRONT PANEL CONNECTORS WITH

CONNECTORS OR CABLE ASSEMBLIES THAT ENSURE OPERATORS WILL NOT

INADVERTENTLY COME IN CONTACT WITH HIGH VOLTAGES.

Page 1.1

LXI FIBER OPTIC MULTIPLEXER 60-850/851

pickering SECTION 1 - TECHNICAL SPECIFICATION

SECTION 1 - TECHNICAL SPECIFICATION

pickeringtest.com

LXI Fiber Optic Multiplexer 40-850/851

ISSUE 5.0 APR 2018

• 8 Channel, Dual 4 Channel,

Dual 8 Channel, 16 Channel or 32 Channel Optical MUX

• MEMS Based Actuation For Long Life and Fast Operation

• Single-Mode or Multi-Mode Fiber Support

• Loop-Thru Option For Easy MUX Expansion

• Compact 1U Form Factor

• LXI Standard 1.4 Compliant

• 3 Year Warranty

Functional Diagrams of the Optical 4, 8, 16 and 32 Channel MUX Conﬁgurations

16-Channel

Multiplexer Ch 1

Ch 2

Ch 3

Ch 4

Ch 5

Ch 6

Ch 7

Ch 8

Ch 9

Ch 10

Ch 11

Ch 12

Ch 13

Ch 14

Ch 15

Ch 16

Com

8-Channel

Multiplexer

Ch 5

Ch 6

Ch 7

Ch 8

Com

Ch 1

Ch 2

Ch 3

Ch 4

8-Channel

Multiplexer Ch 1.1

Ch 1.2

Ch 1.3

Ch 1.4

Ch 1.5

Ch 1.6

Ch 1.7

Ch 1.8

Com 1

Ch 2.1

Ch 2.2

Ch 2.3

Ch 2.4

Ch 2.5

Ch 2.6

Ch 2.7

Ch 2.8

Com 2

8-Channel

Multiplexer

4-Channel

Multiplexer Ch 1.1

Ch 1.2

Ch 1.3

Ch 1.4

Com 1

Ch 2.1

Ch 2.2

Ch 2.3

Ch 2.4

Com 2

4-Channel

Multiplexer

32-Channel

Multiplexer

Ch 9

Ch 10

Ch 11

Ch 12

Ch 13

Ch 14

Ch 15

Ch 16

Ch 17

Ch 18

Ch 19

Ch 20

Ch 21

Ch 22

Ch 23

Ch 24

Com

Ch 1

Ch 2

Ch 3

Ch 4

Ch 5

Ch 6

Ch 7

Ch 8

Ch 25

Ch 26

Ch 27

Ch 28

Ch 29

Ch 30

Ch 31

Ch 32

The 60-850 and 60-851 are LXI conformant ber optic multiplexers that use MEMS

switching technology to ensure fast and reliable switching of single-mode (60-850)

or multi-mode (60-851) optical signals being carried on ber connections. The

60-850/851 is available with a variety of connector options and in a variety of

multiplexer arrangements.

Multiplexer congurations offered are single 8 channel, dual 8 channel, single

16 channel and single 32 channel. Each conguration can be supplied with FC/APC,

SC/PC, LC or SC connector types – allowing users to select exactly the model that ts

their connection standard. A dual 4 channel version is also available, supporting only

multi-mode ber and with LC connectors. Multiplexer versions are also available with

a Loop-Thru connection allowing easy expansion.

All congurations use a MEMS based mirror system that ensures fast switching, long

operating life and repeatable insertion loss and isolation characteristics.

MUX Control

The 60-850/851 is fully LXI conformant

through a 1000Base-T Ethernet

connection and is supplied with IVI

drivers and Direct I/O drivers to allow

programmatic control of the optical

switches. A built in soft front panel

can be accessed through any web

browser to provide manual control of

the multiplexers in a simple and intuitive

way. Controlling the 60-850/851 at long

distances could not be simpler, and

control can even be gained using links

including wireless access points for true

control mobility.

Page 1.2 LXI FIBER OPTIC MULTIPLEXER 60-850/851

pickering

SECTION 1 - TECHNICAL SPECIFICATION

LXI Fiber Optic Multiplexer – 60-850/851

pickeringtest.com

Overview

16-Channel

Multiplexer Ch 1

Ch 2

Ch 3

Ch 4

Ch 5

Ch 6

Ch 7

Ch 8

Ch 9

Ch 10

Ch 11

Ch 12

Ch 13

Ch 14

Ch 15

Ch 16

Common

8-Channel

Multiplexer

Ch 5

Ch 6

Ch 7

Ch 8

Common

Ch 1

Ch 2

Ch 3

Ch 4

8-Channel

Multiplexer Ch 1.1

Ch 1.2

Ch 1.3

Ch 1.4

Ch 1.5

Ch 1.6

Ch 1.7

Ch 1.8

Common 1

Ch 2.1

Ch 2.2

Ch 2.3

Ch 2.4

Ch 2.5

Ch 2.6

Ch 2.7

Ch 2.8

Common 2

8-Channel

Multiplexer

Loop-Thru

Loop-Thru 1

Loop-Thru 2

Switching Diagrams for the 8 Channel Optical Multiplexer with optional Loop-Thru switching

16-Channel

Multiplexer Ch 1

Ch 2

Ch 3

Ch 4

Ch 5

Ch 6

Ch 7

Ch 8

Ch 9

Ch 10

Ch 11

Ch 12

Ch 13

Ch 14

Ch 15

Ch 16

Common

16-Channel

Multiplexer Ch 17

Ch 18

Ch 19

Ch 20

Ch 21

Ch 22

Ch 23

Ch 24

Ch 25

Ch 26

Ch 27

Ch 28

Ch 29

Ch 30

Ch 31

Ch 32

Loop-Thru

Connection

Example Conﬁguration using the Loop-Thru Connection:

Two 60-850/851 16-Channel Multiplexers can be

cascaded to produce a single 32-Channel Optical

Multiplexer

32-Channel

Multiplexer

Ch 9

Ch 10

Ch 11

Ch 12

Ch 13

Ch 14

Ch 15

Ch 16

Ch 17

Ch 18

Ch 19

Ch 20

Ch 21

Ch 22

Ch 23

Ch 24

Ch 1

Ch 2

Ch 3

Ch 4

Ch 5

Ch 6

Ch 7

Ch 8

Ch 25

Ch 26

Ch 27

Ch 28

Ch 29

Ch 30

Ch 31

Ch 32

Common

Loop-Thru

Switching Diagram for the 32 Channel Optical Multiplexer

with optional Loop-Thru switching

16-Channel

Multiplexer Ch 1

Ch 2

Ch 3

Ch 4

Ch 5

Ch 6

Ch 7

Ch 8

Ch 9

Ch 10

Ch 11

Ch 12

Ch 13

Ch 14

Ch 15

Ch 16

Common

8-Channel

Multiplexer

Ch 5

Ch 6

Ch 7

Ch 8

Common

Ch 1

Ch 2

Ch 3

Ch 4

8-Channel

Multiplexer Ch 1.1

Ch 1.2

Ch 1.3

Ch 1.4

Ch 1.5

Ch 1.6

Ch 1.7

Ch 1.8

Common 1

Ch 2.1

Ch 2.2

Ch 2.3

Ch 2.4

Ch 2.5

Ch 2.6

Ch 2.7

Ch 2.8

Common 2

8-Channel

Multiplexer

Loop-Thru

Loop-Thru 1

Loop-Thru 2

Switching Diagram for the 16 Channel Optical Multiplexer

with optional Loop-Thru switching

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Pickering Multiplexeur

Pickering

Pickering PCI 50-725 Manuel utilisateur

Pickering

Pickering 40-666 Manuel utilisateur

Pickering

Pickering 40-650A Manuel utilisateur

Pickering

Pickering PXi 40-660A Manuel utilisateur

Pickering

Pickering 40-612A Manuel utilisateur

Pickering

Pickering 40-736 Manuel utilisateur

Pickering

Pickering 40-615A Manuel utilisateur

Pickering

Pickering 40-611A Manuel utilisateur

Pickering

Pickering 40-675A Manuel utilisateur

Pickering

Pickering 40-670 Manuel utilisateur

Pickering

Pickering PXI Power MUX BRIC 40-571 Manuel utilisateur

Pickering

Pickering 40-570A Manuel utilisateur

Pickering

Pickering 4 784B Series Manuel utilisateur

Pickering

Pickering 40-613A Manuel utilisateur

Pickering

Pickering 40-680 Manuel utilisateur

Pickering

Pickering SYSTEM 10 Manuel utilisateur

Pickering

Pickering 50-670C Manuel utilisateur

Pickering

Pickering 40-610A Manuel utilisateur

Pickering

Pickering PCI 50-670 Manuel utilisateur

Pickering

Pickering PXI 40-785B Manuel utilisateur

Pickering

Pickering PXI 40-883A Manuel utilisateur

Pickering

Pickering 60-721A Manuel utilisateur

Pickering

Pickering 40-682A Manuel utilisateur

Pickering

Pickering PXI 40-655 Manuel utilisateur

Manuels Multiplexeur populaires d'autres marques

Campbell

Campbell AM416 Manuel utilisateur

Paradyne

Paradyne SIM2000 Manuel utilisateur

Panasonic

Panasonic WJFS616 - SWITCHER Manuel utilisateur

Lanex

Lanex TM-77 Manuel utilisateur

Bosch

Bosch VSS8394/01T Manuel utilisateur

Quark-Elec

Quark-Elec QK-A035 Manuel utilisateur

ADTRAN

ADTRAN Frameport 768 Manuel utilisateur

Elo TouchSystems

Elo TouchSystems E247 Manuel utilisateur

Paradyne

Paradyne Hotwire 8786 Manuel utilisateur

RFL Electronics

RFL Electronics 9508D UCC Manuel utilisateur

Miranda

Miranda AMX-101i Mode d’emploi

ShipModul

ShipModul MiniPlex-AIX NMEA-0183 Manuel utilisateur

GE StoreSafe SDVR-10 Manuel utilisateur

American Fibertek

American Fibertek MTX-8410C Manuel utilisateur

ADC

ADC HiGain ELU-319 5E Manuel utilisateur

Paradyne

Paradyne Hotwire 8774 Manuel utilisateur

American Fibertek

American Fibertek MTX-8810C-SL Manuel utilisateur

Viessmann

Viessmann 5229 Manuel utilisateur