Phonak CROS II Manuel utilisateur

Phonak CROS solutions

February 2018

Desktop Fitting Guide

This guide provides you with a detailed introduction to fitting a Phonak CROS II or a Phonak CROS B system in Phonak Target

5.3and later. For fitting of the hearing instruments, please see the Hearing Instruments Desktop Fitting Guide.

Preparation of the hearing instruments

For the fitting of CROS II or CROS B it is recommended to use iCube II as it enables faster fine tuning and instant

demonstration of the CROS system.

CROS II can only be fit with Venture hearing instruments.

CROS B can only be fit with Belong™hearing instruments.

iCube II

No cables to the hearing instrument or CROS device are

needed. Insert batteries before placing the devices on the ear.

Turn on the devices by closing the battery compartment.

NOAHlink or HI-PRO

Connect the programing cables to the hearing instruments

and the fitting device. It is not possible to demonstrate the

CROS device with the cables connected.

Connect the instruments

Click [Connect] to start the fitting. The connected devices will appear

next to the fitting device in the dashboard.

The audiogram data from NOAH will be automatically imported into

Phonak Target and taken into account for the pre-calculation.

After the connection, select the correct acoustic parameters for your

hearing instruments.

Confirm that the correct fitting device is shown. To change the

fitting device, use the pull down arrow next to the fitting device

in the dashboard.

Phonak Target 5.3 | Phonak CROS solutions

Basic tuning

Go to the [Fitting] tab and run the feedback test. Once completed, fit

the hearing instrument as in a monaural fitting.

After fitting, go to the [Global tuning] tab and select [CROS Balance].

Adjust the loudness ratio between the CROS device and the hearing

instrument.

Device options

Click [Device options] to adjust the individual settings for the CROS volume / volume and program change (depending on the

user controls available).

For CROS II or CROS B, the volume of the CROS signal can be adjusted separately, if desired.

Finishing the fitting session

You can close the session at any time by clicking [Save & close session] in the top right corner of the screen. The save dialog

will confirm the successful save of the CROS fitting.

The wireless connection between the CROS transmitter and hearing aid starts automatically once both instruments have been

disconnected from the fitting device and turned on.

Important: When streaming from the accessories, the CROS streaming will be automatically disconnected.

Reconnection will also be automatic when you stop streaming of the accessory.

CROS fitting in Junior Mode

For more information, please see the Pediatrics Desktop Fitting Guide.

CE mark applied 2017

Sonova AG

Laubisrütistrasse 28

CH-8712 Stäfa

Switzerland

Ce manuel convient aux modèles suivants

Autres manuels Phonak Prothèse auditive

Phonak

Phonak Audeo P-R Series Manuel utilisateur

Phonak

Phonak Serenity SP Manuel utilisateur

Phonak

Phonak Roger On Manuel utilisateur

Phonak

Phonak Una CIC/MC Manuel utilisateur

Phonak

Phonak Roger Focus II-312 Manuel utilisateur

Phonak

Phonak Sky V90-M Manuel utilisateur

Phonak

Phonak M H20 Manuel utilisateur

Phonak

Phonak eXtra Manuel utilisateur

Phonak

Phonak Q90 Manuel utilisateur

Phonak

Phonak EasyCall Manuel utilisateur

Phonak

Phonak Roger Covert 2.0 Manuel utilisateur

Phonak

Phonak Behind-the-Ear hearing aids Manuel utilisateur

Phonak

Phonak Cassia Manuel utilisateur

Phonak

Phonak Brio 4 B-13 Manuel utilisateur

Phonak

Phonak Virto V Manuel utilisateur

Phonak

Phonak EasyCall Manuel utilisateur

Phonak

Phonak ComPilot Manuel utilisateur

Phonak

Phonak Baseo Q15 Manuel utilisateur

Phonak

Phonak ComPilot Manuel utilisateur

Phonak

Phonak Perseo Mode d’emploi

Phonak

Phonak Audeo MINI Manuel utilisateur

Phonak

Phonak ComPilot Manuel utilisateur

Phonak

Phonak TVLink II Manuel utilisateur

Phonak

Phonak Una Manuel utilisateur

Manuels Prothèse auditive populaires d'autres marques

Sonic

Sonic Bliss miniBTE Manuel utilisateur

Lexie

Lexie B1 Manuel de la liste des pièces

Widex

Widex FM+DEX Manuel utilisateur

Siemens

Siemens Triano Manuel utilisateur

Camplicomms

Camplicomms HC-200 Manuel utilisateur

Widex

Widex SUPER 220 S2-VSD Manuel utilisateur

Williams Sound

Williams Sound SoundPlus WIR 237 Mode d’emploi

Oticon Medical

Oticon Medical Ponto SoundConnector Manuel utilisateur

Siemens

Siemens Life micon Manuel utilisateur

Starkey

Starkey Destiny Manuel utilisateur

Audicus

Audicus The Icon Manuel utilisateur

Advanced Bionics

Advanced Bionics Slim HP Standard Manuel utilisateur

Widex

Widex DREAM440 THE DREAM SERIES Manuel utilisateur

NIKEN

NIKEN NK-401 Manuel utilisateur

ON Semiconductor

ON Semiconductor Ezairo 7111 Pre Suite Manuel utilisateur

Sonetik

Sonetik GOHEAR Manuel utilisateur

Widex

Widex FL-9 Manuel utilisateur

Siemens

Siemens MUSIC Pro Pro IT Manuel utilisateur