Phoenix SS1190E Citadel Manuel utilisateur

SS1190E Citadel Instructions

a) To switch on the lock power supply, press button <<ON>>.

b) The lock is set on the factory default code of 1,2,3,4,5,6.

c) Enter the default code (1,2,3,4,5,6) the correct code is confirmed by the flashing green LED.

1. Lock opening

The new code combination should be entered with the lock and safe door in the open postion.

a) Open the lock with the valid primary code (see 1.);

Press <<ON>>;

Press button <<P>>.

Enter valid code 1-2-3-4-5-6 or former user code (if the green LED is illuminated continuously, the operation is correct completed);

Enter new 6-digit code X-X-X-X-X-X (if after entering the green LED is illuminated continuously and acoustic signal sounds twice,

the operation is correct).

Repeat the procedure again: Enter the new 6-digit code X-X-X-X-X-X (if after entering the green LED is illuminated continuously and

acoustic signal sounds twice, the operation is correct ) and the new code is set.With the door in the open position test the new 6-digit

X-X-X-X-X-X again (if after entering the green LED flashes once, the operation is completed). The door can be opened.

It is recommended to record the new code combination and to safely store it outside the safe.

2. Change of Code Combination

If the code is entered incorrectly the red LED flashes 3 times. After 3 incorrect entries the lock goes into a two minute blocked status. The period

in which the lock is blocked is extended to 4,8 and a maximum of 16 digits every time an incorrect code is entered.

3. Lock blocking

Turn the bar handle counter clockwise in “close”-position until stop reached. The lock is blocked (bar handle is in horizontal position).

4. Locking

Low voltage is indicated, if the red LED flashes 10 times after opening. Please change the battery immediately. Open the safe, lift out the battery

cover on the inner side of the door (figure 2.) insert the new 9v battery;

Code combination remains saved even if battery is discharged

If the battery is not charged and the lock is not receiving sufficient power to open, a new battery can be connected by an external supply clip.

The supply clip is located on the control panel under the logo sticker KABA * (Figure 3).

5. Power Supply / Changing the batteries

123

45 6

789

0 P

Figure 1. Appearance

Figure 3. Battery outer connection

123

45 6

789

0 P

Figure 2.

Base fixing instructions for the

SS1190E Citadel Series

a) To switch on the lock power supply, press button <<ON>>.

b) The lock is set on the factory default code of 1,2,3,4,5,6.

c) Enter the default code (1,2,3,4,5,6) the correct code is confirmed by the flashing green LED.

YOU WILL REQUIRE

1) Look for a place that does not restrict access and the swing of the door.

2) Ensure that the floor is level.

3) For best results a concrete floor is preferable.

CHOOSING A PLACE TO INSTALL YOUR SAFE

1) Manoeuvre the safe into the required position. Now with the pencil mark the floor around the safe. (If the safe is against a wall then just the

front and sides needs to be marked)

2) Open the safe door.

3) Remove the bolt cover tray on the bottom of your safe to reveal the base fixing holes.

4) Mark the positions on the floor for drilling. Use the pencil through the base fixing holes in the base of the safe.

5) Now move the safe to one side, giving you access to the markings on the floor

6) Before using the 20mm drill bit. With the ruler measure 120mm from the tip of the bit and put a piece of adhesive tape around the bit to

ensure you do not drill too deep.

7) Drill the 20mm holes in the floor until you reach your 120mm adhesive tape marker.

8) Clean around both of the holes in the floor.

9) There are four parts to each of your two bolts

a. A socket head bolt

b. A washers (steel)

c. A 24mm washer with a 30mm spacer welded to it

d. 74mm shield

10) Take the washer with spacer attached and insert it into the hole in the ground, now with the pencil drawer around the washer. Now remove

the washer/spacer and with the large screwdriver gouge out the surface around the holes to a depth of 2.5mm. This will let the washers sit

flush with the floor.

11) Take the 74mm shields and the 30mm spacers, insert these into the drilled holes. The shield first with the plastic cap covering the end going

down the hole first.

12) Place the safe back into position, using the pencil lines on the floor. Now place the steel washers onto the bolts and insert the bolts through

the base of the safe, into the floor and right down through the spacer into the shield and tighten until you can not turn the Allen key any further.

13) Replace the bolt cover tray.

YOUR SAFE IS NOW BASE FIXED.

DRILLING & BOLTING

Version 1/JPT/Sept 11

Thank you for purchasing a Phoenix Safe. Your safe is ready prepared for base fixing. To base fix your safe, follow instructions below.

HOW TO BOLT YOUR SAFE DOWN

Table des matières

Autres manuels Phoenix Sûr

Phoenix

Phoenix SS1160 Fiche d'information produit

Phoenix

Phoenix SS0100E Fiche d'information produit

Phoenix

Phoenix Fire Fox SS1621E Manuel utilisateur

Phoenix

Phoenix SS0992E Manuel utilisateur

Phoenix

Phoenix VENUS HS0656 Fiche d'information produit

Phoenix

Phoenix FS0440F Fiche d'information produit

Phoenix

Phoenix NESO SS0200F Series Manuel utilisateur

Phoenix

Phoenix SS1180K Manuel utilisateur

Phoenix

Phoenix PS610-E36 Fiche d'information produit

Phoenix

Phoenix FS1920E Fiche d'information produit

Phoenix

Phoenix SPECTRUM LS6000 Manuel utilisateur

Phoenix

Phoenix Elara HS3550 Fiche d'information produit

Phoenix

Phoenix KS0030E Series Manuel utilisateur

Phoenix

Phoenix DIONE SS0313E Manuel utilisateur

Phoenix

Phoenix SS1170K Manuel utilisateur

Phoenix

Phoenix Dream Series Manuel utilisateur

Phoenix

Phoenix FS2230K Series Manuel utilisateur

Phoenix

Phoenix FS0352C Series Manuel utilisateur

Phoenix

Phoenix FS2250K Series Manuel utilisateur

Phoenix

Phoenix KS0030E Series Manuel utilisateur

Phoenix

Phoenix NEPTUNE HS1056 Fiche d'information produit

Phoenix

Phoenix FS0440E Manuel utilisateur

Phoenix

Phoenix KS0030E Series Manuel utilisateur

Phoenix

Phoenix Neptune HS1050 Fiche d'information produit

Manuels Sûr populaires d'autres marques

Squire

Squire Stronghold Keysafe Manuel utilisateur

Vaultek

Vaultek 10 Series Fiche technique

Arregui

Arregui CLASS Manuel utilisateur

Beaumont

Beaumont SMART KEYBOX Manuel utilisateur

Honeywell

Honeywell 2077D - 1.21 Cubic Foot Anti-Theft Safe Manuel utilisateur

Hornady

Hornady SnapSafe Trunk Safe II Manuel utilisateur

SPORTS AFIELD

SPORTS AFIELD SA-HD5-BIO Manuel utilisateur

Honeywell

Honeywell 5912 Manuel utilisateur

Technomax

Technomax Trony Series Manuel

SPORTS AFIELD

SPORTS AFIELD INSTINCT BIOMETRIC Series Manuel utilisateur

RICHTER CZECH

RICHTER CZECH LA Manuel d'utilisation

Olymp

Olymp GOsafe 110 Manuel utilisateur

Clarke

Clarke Strong-Arm CS1000K Mode d’emploi

Ankaro

Ankaro ANK EZ I Manuel utilisateur

Intratone

Intratone KEY SAFE Mode d’emploi

Costway

Costway HW50956 Manuel utilisateur

Megasat

Megasat K Series Manuel utilisateur

ECOSAFE

ECOSAFE 3030ARD Manuel utilisateur