Philips 37HF7444/10 Manuel utilisateur

Information for users in the UK (not applicable outside the UK)

Positioning the TV

For the best results, choose a position where light does not fall directly on the screen, and at some

distance away from radiators or other sources of heat. Leave a space of at least 5 cm all around the

TV for ventilation, making sure that curtains, cupboards etc. cannot obstruct the air flow through the

ventilation apertures. The TV is intended for use in a domestic environment only and should never be

operated or stored in excessively hot or humid atmospheres.

Interference

The Department of Trade and Industry operates a Radio Interference Investigation Service to help

TV license holders improve reception of BBS and IBA programmes where they are being spoilt by

interference.

If your dealer cannot help, ask at a main Post Office for the booklet “How to Improve Television and

Radio Reception”.

Mains Connection

Before connecting the TV to the mains, check that the mains supply voltage corresponds to the

voltage printed on the type plate on the rear panel of the TV. If the mains voltage is different, consult

your dealer.

Important

Should it become necessary to replace the mains fuse, this must be replaced with a fuse of the same

value as indicated on the plug.

1. Remove fuse cover and fuse.

2. The replacement fuse must comply with BS 1362 and have the ASTA approval mark. If the

fuse is lost, make contact with your retailer in order to verify the correct type.

3. Refit the fuse cover

In order to maintain conformity to the EMC directive, the mains plug on this product must not be

removed.

Connecting the aerial

The aerial should be connected to the socket marked at the back of the set. An inferior aerial is

likely to result in a poor, perhaps unstable picture with ghost images and lack of contrast. Make-shift

loft or set-top aerials are often inadequate. Your dealer will know from experience the most suitable

type for your locality.

Should you wish to use the set in conjunction with other equipment, which connects to the aerial

socket such as TV games, or a video camera it is recommended that these be connected via a

combiner unit to avoid repeated connection and disconnection of the aerial plug.

Fitting the stand (if provided)

Use only the stand provided with the set, making sure that the fixings are properly tightened. A

diagram showing how to assemble the stand is packed with the stand. Never use a make-shift stand,

or legs fixed with woodscrews.

- 2 -

hank you for purchasing this television set.

This handbook has been designed to help you install and operate your TV set.

e stron

recommend that

ou read it thorou

ccess Code / Code d'accès / Zugangkennziffer / Codice di accesso / Código de acceso

When the set is in the Standard Security Mode, the Set-up Menu may be accessed either with an

Institutional Set-up Remote Control, or with a guest remote control (like the RC2886) by pressing

the following Remote Control keys in sequence: 3 1 9 7 5 3 Mute

Care of the screen

Do not touch, push or rub or strike the screen with anything hard as this may scratch, mar or

damage the screen permanently. Do not rub with dust clothes with chemical treatment. Do not

touch the surface with bare hands or greasy cloth (some cosmetics are detrimental to the screen).

Unplug the TV before cleaning the screen. When the surface becomes dusty, please wipe gently

with absorbent cotton or other soft materials like chamois soaks. Do not use acetone, toluene and

alcohol because they cause chemical damage.

Do not use liquid cleaners or aerosol cleaners. Wipe off saliva or water drops as soon as possible.

Their long time contact with the screen causes deformations and colour fading.

Environmental

• Your television contains material that can be recycled and reused by specialized companies. Please

find out about local regulations on the disposal of your old television set. Pay particular attention

to the disposal of exhausted batteries.

• Your television consumes energy in the stand-by mode. Energy consumption contributes to air

and water pollution. We advise you to switch off your television overnight instead of leaving it in

stand-by mode.

he packaging of this product is intended to be recycled. Apply to the local

authorities for correct disposal.

Disposal of your old product.

our product is designed and manufactured with high quality materials and

components, which can be recycled and reused.When this crossed-out wheeled bin

symbol is attached to a product it means the product is covered by the European

Directive 22002/96/EC. Please find out more about the separate collection system for

electrical and electronic products in your local neighbourhood.

Please act according to your local rules and do not dispose of your old products with

your normal household waste. The correct disposal of your old product will help

prevent potential negative consequences for the environment and human health.

- 3 -

Wall mounting instructions/Table stand

According to the type of TV you’ve purchased a wall mount bracket and/or stand may be supplied.

To mount the supplied stand and/or wall mount bracket, refer to separate instructions. Make sure

that the wall mount is fixed securely so that it meets safety standards.

Make sure that air can circulate freely through the ventilation slots

o prevent any unsafe situations, no naked flame

sources, such as lighted candles, should be placed

on or in the vicinity. Avoid heat, direct sunlight and

exposure to rain or water. The equipment shall not

be exposed to dripping or splashing and no objects

filled with liquids, such as vases, shall be placed on

it. Insert the aerial plug firmly into the aerial socket

at the bottom of the TV.

Connecting the Mains

Insert the mains plug into the wall socket and switch on. Please refer to the label on the back of the

television for the correct operating voltage.

Installing the remote control

•

Remove the cover at the back of the

remote control.

• Insert the correct type and size batteries

into the compartment making sure they

are the right way around.

• You can secure your batteries by

fastening an appropriate screw into the

hole of the battery cover.

Switch the TV on:

Press the power switch on the TV. An indicator on the front of the TV lights up and the screen

comes on. If the TV is in standby mode (red indicator), press the – TV + keys on the remote control.

- 4 -

Accessing the Set-up Menu

When the set is in the High Security Mode, the Setup menu can be accessed only with an Institutional

Set-up Remote Control (RG4172BK or RC2573).

When the set is in the Standard Security Mode, the Set-up Menu may be accessed either with an

Institutional Set-up Remote Control, or with a guest remote control (like the RC2886) using an

authorized access code.

RG4172BK RC 2573

Navigation

The current menu item can be selected by means of the cursor up and cursor down keys.

Submenus can be accessed from menu items with a “>” symbol pressing the cursor right key.

• To exit any menu press “Menu” button

• Select “YES” to activate/enable a setting, “NO” to deactivate/disable.

• TELEVISION up/down, INFO up/down, PAY-TV up/down and

RADIO up/down are active in menu mode and the television reacts the

same way as in TV mode.

- 5 -

• Language: Select the language of the installation menu. Options are "ENGLISH",

"ITALIANO", "DEUTSCH", and "FRANCAIS".

• Communication: The Communication menu is required to enable interactive applications.

For more information, consult the respective application notes. For stand-alone applications

select “OFF”.

• No. of Programs: This sub menu allows setting the number of Television, PAY-TV, Radio

and Info programs. The overall maximum number of programs is 125.

• Program Install: In the Program Install sub-menu, program settings can be set.

• Configuration: In the Configuration menu, various settings and features of the TV can be

adjusted.

• Clock Setup: The Clock set-up menu can be entered from this menu item (this menu option is

only available on certain LCD TV models).

- 6 -

In the Program Installation sub-menu, program settings can be set. When this menu is open, all the

protections are inactive.

• Program No.: The program type can be selected with the cursor left/right buttons. These buttons

will toggle between all available types: "TV", "INFO", "PAYTV" and "RADIO".

If the program number of a certain type is 0, the corresponding type is not displayed. In order to

display a program number of the above-mentioned types, always enter two numbers, for example:

“01” for TV1 or digit “1” and up/down cursor.

• Input:

he "Input" menu item selects the desired input source that will be assigned to the program.

Possible values are TUNER, AV1, AV2, S-VIDEO, SIDE AV, SIDE S-VIDEO, CARD-CVBS,

CARD-YC, EXT4, CARD-EXT4, HDMI1 and HDMI2. Some input sources may not be available

on certain sets (see accompanying table).

Model / Input AV1 AV2 Side AV Side S-Video EXT4 HDMI

26HF5444 Scart1 Scart2

CVBS

AV-In S-Video In YPbPr HDMI1 /

HDMI2

26HF7874 Scart1 Scart2

CVBS

AV-In S-Video In YPbPr HDMI1 /

HDMI2

32HF7444 Scart1 Scart2

CVBS

AV-In S-Video In YPbPr HDMI1 /

HDMI2

32HF7874 Scart1 Scart2

CVBS

AV-In S-Video In YPbPr HDMI1 /

HDMI2

37HF7444 Scart1 Scart2

CVBS

Video In S-Video In YPbPr HDMI1 /

HDMI2

Note: When a SmartCard XPress Box is used, it is usually connected to Scart1.

- 7 -

• System: WEST EU (PAL/SECAM-BG), EAST EU (PAL/SECAM-DK), UK (PAL-I), and

FRANCE (SECAM-L/L').

• Frequency: Digits can be entered for a frequency in MHz. Right cursor starts an auto search;

during frequency entry the digits not yet entered are displayed as dashes "-". Enter “0” for

frequencies below 100 MHz.

• Label: This menu item will be used to add a label/name for each program.

o Pressing the left/right buttons you may enter or exit the label field; pressing the

up/down cursor you may insert alphanumeric characters.

o Pressing M (Menu button) you may exit the Label Menu item.

• Store: The present program information is stored after pressing the cursor left/right button.

Press Menu to exit without storing.

• Fine Tune: Using the "control left/right" commands starts fine-tuning.

• Mute: This item enables/disables picture and sound for the particular channel.

o NONE: normal picture and sound enabled

o VIDEO: picture is blanked for this channel (e.g. radio channel)

o AUDIO: sound is muted for this channel (e.g. information channel)

• Teletext Language: This menu enables the user to select the Teletext character set to be used

for the selected channel. With cursor left/right you can select a letter corresponding to the

different language clusters.

o “WEST EU”: Pan European (Latin) / West option

o “EAST EU”: Pan European (Latin) / East option (this menu option is only available on

certain LCD TV models)

o “GREEK”: Greek

o “CYRILLIC”: Cyrillic (this menu option is only available on certain LCD TV models)

• Protection: This function indicates whether the selected program has a protection or not. With

the cursor left/right keys the protection can toggle between "YES" and "NO".

In the Configuration menu, various settings and features of the TV can be adjusted.

•

Switch On/OSD: In this sub-

menu the behavior of the TV after

switching on and the behavior of

the On Screen Display can be

selected.

• Picture/Sound: In this sub-menu,

the Picture and Sound settings of

the TV can be selected.

• Security: In this sub-menu, the

Security settings of the TV can be

configured.

• Control: In this sub-menu, the

Control settings of the TV can be

configured.

• Features: In this sub-menu,

advanced features of the TV can be

accessed.

- 8 -

In this sub menu the behavior of the TV after switching on and the behavior of the On Screen

Display can be selected.

•

Welcome Message: Press Cursor

Left/Right to display Welcome

message entry menu:

o Display

o Line 1

o Line 2

o Clear

With the Cursor Up/Down you

can set the message characters.

• Switch On Program: This item

sets the television’s program at

switch on.

• Switch On Volume: This item sets the television’s volume at switch on. Use the

Right/Left Cursor buttons to adjust.

• Switch On Pic Fmt: This item sets the television’s Picture Format at switch on. Use the

Right/Left Cursor buttons to adjust.

• Power On: The Power On menu function defines the behavior of the television whenever

AC Power is applied. The valid states are "ON", "FORCED ON", "LAST STATUS" and

“STANDBY”.

o When “ON” & “FORCED ON”, the television can only be switched OFF by

means of the main switch or a set-up remote control or by ESP function (Energy

Saving Programmability controls the maximum continuous viewing time allowed

by the control system).

o When “LAST STATUS”, the television switches on the previous status, ON or

Stand-by.

o When “STANDBY”, the television always switches on in Stand-by.

• Volume Indicator: To display volume indicator when adjusting volume, select "YES".

Select “NO” to hide the volume indicator.

• Program Display: Program Display values can be: Number, Label, All, None.

- 9 -

In this sub menu, the Picture and Sound settings of the TV can be selected.

• Brightness: This changes picture brilliance.

• Colour: This changes the intensity of the colour.

• Contrast: This changes the difference between the light and dark tones.

• Sharpness: This changes the picture definition.

• Tint: Adjusts the picture to obtain natural skin tones.

• Active Control: Active Control optimises the quality of the picture according to the quality of

reception (this menu option is only available on certain LCD TV models).

• Treble/Bass: This adjusts the level of treble and bass effects on the TV’s sound output.

• Balance: This balances the sound on the left and right speakers.

• AVL (Automatic Volume Leveller): This is used to limit increases in sound, especially on

programme change or advertising slots.

- 10 -

Autres manuels pour 37HF7444/10

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Philips TV

Philips

Philips 32PFL4606H/60 Manuel utilisateur

Philips

Philips TPE1.1U LA Manuel utilisateur

Philips

Philips 50PUT6800 Manuel utilisateur

Philips

Philips 55PFL6900/F7 Manuel utilisateur

Philips

Philips 7603 series Manuel utilisateur

Philips

Philips 42PF7220A/37B Manuel utilisateur

Philips

Philips 50PUS8548 Manuel utilisateur

Philips

Philips 19PFL4322/45 Manuel utilisateur

Philips

Philips PR0925B Manuel utilisateur

Philips

Philips 19-MONO COLOR TV W-REM CONT-CHARCOAL-20LL200 Manuel utilisateur

Philips

Philips 32DW9625/05 Manuel utilisateur

Philips

Philips 19PFL5622D/37E Manuel utilisateur

Philips

Philips 8807 Series Manuel utilisateur

Philips

Philips 28PW9512 Mode d’emploi

Philips

Philips 24PHT5565 Manuel utilisateur

Philips

Philips 37DC2090 Manuel utilisateur

Philips

Philips 25HT5405 Manuel utilisateur

Philips

Philips 25HT5405/01B Manuel utilisateur

Philips

Philips 32PF9968/10 Manuel utilisateur

Philips

Philips 4022 series Manuel utilisateur

Philips

Philips 32PFL3404D Manuel utilisateur

Philips

Philips 20RF40S Manuel

Philips

Philips Essence 5000 Series Manuel utilisateur

Philips

Philips 29PT5308 Manuel utilisateur

Manuels TV populaires d'autres marques

Toshiba

Toshiba 27A10 Manuel utilisateur

Hitachi

Hitachi 32FX48B Manuel utilisateur

DAEWOO ELECTRONICS

DAEWOO ELECTRONICS DTQ-14V1FC Manuel utilisateur

Changhong Electric

Changhong Electric uhd55b6000is Manuel utilisateur

Panasonic

Panasonic Genus TX-G10 Manuel utilisateur

Toshiba

Toshiba 19A20 Manuel utilisateur

Sony

Sony XBR-100Z9D Manuel utilisateur

Samsung

Samsung 55S9 B Series Manuel utilisateur

Sharp

Sharp LC-40FI5012E Manuel utilisateur

Loewe

Loewe Table Stand Reference 55 Manuel utilisateur

Sylvania

Sylvania 6427FB Manuel utilisateur

Sanyo

Sanyo CE19LD90N-B Manuel utilisateur

North State

North State TV2GO Manuel utilisateur

RCA

RCA RTU7877 Manuel utilisateur

Sharp

Sharp 21K-FG1RU Manuel utilisateur

Sony

Sony Esprit TAV-L1 Manuel utilisateur

Grundig

Grundig 43 VLE 4820 Manuel utilisateur

Samsung

Samsung LN26C350D1D Manuel utilisateur