Philips FlexTune Manuel utilisateur
June 2021
Tunable White
Systems
Quick Installation Guide
FlexTune Quick Installation Guide
FlexTune
3
Introduction
Philips FlexTune offers a complete, easy-to-install, and future-proof Tunable White System. This Quick Installation Guide explains the basics
and helps you to get up-and-running. For full explanation, several in-detail technical documents can be downloaded from our website (see
page 11)
>
<
4
The FlexTune Building Blocks
A Philips FlexTune System consists of at least three components:
1. A Philips Xitanium FlexTune driver
2. A Tunable White (TW) module, for instance a Philips Fortimo FlexTune module
3. A TW control system, complying to the DALI 209 Standard.
a. Wireless: A TW-compatible node in combination with commissioning app (e.g. Philips EasyAir SNS210 MC
and the Philips field app MC) and a compatible wireless switch
b. Wired: A DALI 209 TW control module
c. Touch & Dim (TD): This feature is based on applying momentary mains voltage by means of two
momentary push buttons to the SR-DA interface. These push buttons can be used to turn on/off and dim
up/down the light (push button 1) and to change the color temperature (push button 2)
To this basic system, additional components such as additional (wireless) switches and various types of sensors can be added. The
number of drivers, modules, and additional components, as well as the complexity of the control system is virtually unlimited, and can
be designed according to your requirements.
Note:
By factory default this SR bus power supply (SR PSU) is enabled, and ready to be used with an external control device. It can be
disabled/re-enabled with MultiOne configuration tools and software.
The driver SR PSU must be disabled in case:
1. The drivers are used in a wired DALI network.
2. The Touch and Dim feature is used.
Note that the SR PSU must be disabled on individual driver level before installation in a system.
<
>
How to build a wireless TW-System
1. Configure the driver
Make sure that driver settings match the properties of the modules. These settings can be accessed via SimpleSet using MultiOne
software and a proper NFC-tool. The driver current (AOC) has to be set according to your requirements.
More in-detail information of driver configuration via MultiOne can be found in the design-in guides mentioned on page 11.
2. Connect the building blocks:
a. Connect the module to the driver, this usually requires four wires per module. Pay attention to the labels printed close to the
connectors of both module and driver. Example: CW+ stands for Cool White plus. Connect this pin of the connector of the
module to the corresponding pin of the connector of the driver.
b. Connect the node to the driver, this is a two-wire connection to the SR-pins of the driver (see picture below). For the EasyAir
SNS210 MC, plus and minus are interchangeable. For other nodes, check if the plus connection of the node must be
connected to the SR+ pin of the driver.
3. Install the commissioning app, e.g. Philips field app MC.
4. Switch on the system and start the app.
5. Commission the switch (and other components you want to add) with the app.
6. Optionally: Use the app to create Zones and Scenes according to your wishes
5
module
connections
node
connections
Xitanium FlexTune Driver Node
4-wire driver to module
connection
2-wire driver to node
connection
Fortimo FlexTune Module
4-wire driver to module
connection
Cell Phone with
MasterConnect app
Basics of a Wireless TW-System
6
Wireless Switch
How to build a wired TW-System
1. Configure the driver
Make sure that driver settings match the properties of the modules. These settings can be accessed via SimpleSet using MultiOne
software and a proper NFC-tool. The driver current (AOC) has to be set according to your requirements.
More in-detail information of driver configuration via MultiOne can be found in the design-in guides mentioned on page 11.
2. Connect the building blocks:
a. Connect the module to the driver, this usually requires four wires per module. Pay attention to the labels printed close to the
connectors of both module and driver. Example: CW+ stands for Cool White plus. Connect this pin of the connector of the
module to the corresponding pin of the connector of the driver.
b. Connect the DALI 209 control module to the driver, this is a two-wire connection to the SR-pins of the driver. The plus
connection of the control module must be connected to the SR+ pin of the driver.
Please note: DALI 207 Controls with dual addessing mode are not supported by the FlexTune drivers.
7
module
connections
control module
connections
Xitanium FlexTune Driver
Dali 209 compatible
Control Module
4-wire driver to module
connection
2-wire driver to control
module connection
Fortimo FlexTune Module
Basics of a Wired TW-System
8
How to build a TW-System with Touch & Dim
1. Configure the driver
Make sure that driver settings match the properties of the modules. These settings can be accessed via SimpleSet using MultiOne
software and a proper NFC-tool. The driver current (AOC) has to be set according to your requirements.
More in-detail information of driver configuration via MultiOne can be found in the design-in guides mentioned on page 11.
2. Connect the building blocks:
a. Connect the module to the driver, this usually requires four wires per module. Pay attention to the labels printed close to the
connectors of both module and driver. Example: CW+ stands for Cool White plus. Connect this pin of the connector of the
module to the corresponding pin of the connector of the driver.
b. Connect the double push button to the driver and mains, according to the diagram on the next page. More details about
Touch & Dim can be found in the Design-in Guide Xitanium SR-drivers (see reference on page 11)
9
module
connections
push button
connections
see next
page
Xitanium FlexTune Driver
Double push button
4-wire driver to module
connection
Fortimo FlexTune Module
Basics of a T&D TW-System
10
Table des matières
Autres manuels Philips Équipement d'éclairage
Philips
Philips Halogen MR16 Manuel utilisateur
Philips
Philips 56432-31-16 Manuel utilisateur
Philips
Philips ED-37 Manuel utilisateur
Philips
Philips LX25 Series Manuel utilisateur
Philips
Philips VL440 Spot Manuel utilisateur
Philips
Philips Vari-Lite Manuel utilisateur
Philips
Philips CoreLine tempo medium Manuel utilisateur
Philips
Philips 30504 Manuel utilisateur
Philips
Philips RS772B Manuel utilisateur
Philips
Philips SC Series Manuel utilisateur
Philips
Philips SM500T Manuel utilisateur
Philips
Philips ColorGraze IntelliHue Powercore BCS559 30x60 RGBMW... Manuel utilisateur
Philips
Philips Ligholier KUBIK 1.0 SL110A Manuel utilisateur
Philips
Philips VARILITE VLX3 Manuel utilisateur
Philips
Philips CosmoPolis Urban Lighting Manuel utilisateur
Philips
Philips PLFRESNEL 1 LED LUMINAIRES Mode d’emploi
Philips
Philips 40801 U7 Series Manuel utilisateur
Philips
Philips hue 40801 Series Manuel utilisateur
Philips
Philips 32146-48-16 Manuel utilisateur
Philips
Philips ClearWay BGP303 Guide de l'utilisateur
Manuels Équipement d'éclairage populaires d'autres marques
Qazqa
Qazqa Suplux SL 3 Black 103062 Manuel utilisateur
Commercial Electric
Commercial Electric 54568141 Manuel utilisateur
CREE LIGHTING
CREE LIGHTING 304 Series Manuel utilisateur
Goobay
Goobay 49867 Manuel utilisateur
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Manuel utilisateur
Alkalite
Alkalite Krypton KT-81 Manuel utilisateur
