Philips TD6816/BB051P Manuel utilisateur
Safety information
The marking on the product certifies its conformity with the technical
regulations for user safety and electromagnetic disturbance which were
applicable on the date of approval in accordance with European Union
Directive No. N° 73/23/EEC, 89/336/EEC, 91/263/EEC and 93/68EEC.
Power requirements
This product requires an electrical supply of 230 volts, alternating
monophased current, excluding IT installations defined in standard
EN 60-950.
Warning:
The electrical network is classified as dangerous according to criteria in
the standard EN 60-950.
The only way to power down this product is by unplugging the power cable
from the electrical outlet. Make sure the electrical outlet is located close to
the apparatus and is always easily accessible.
It is recommended that this telephone be used as a complement to
another telephone which does not require mains power.
Safety precautions
•Do not allow the handset to come into contact with water.
•Do not open the handset or the charger. This could expose you to
high voltages. Contact our after-sales service for all repairs.
•Do not allow the charging contacts or the battery to come into
contact with conductive materials such as keys, paper clips, rings,
bracelets, etc.
•Make sure you insert the batteries with their polarities in the correct
position.
Contents 5
Contents
Introduction 2
Installing your extra handset 3
Deciding where to put the charger 3
Installing the charger on a horizontal surface 3
Mounting the charger on a wall 4
Charging your handset 5
Selecting the menu language 5
Registering your extra handset with your Onis base station 6
Changing the name of your base station 7
Using your extra handset 8
Making an outside call 8
Answering an outside call 9
Making an internal call 9
Answering an internal call 10
Using the handset loudspeaker 10
Managing the Baby Sit mode 10
Transferring calls 11
Managing a conference call 12
Locking the handset keypad 12
Using the battery saver 13
Maintenance 14
Changing the battery 14
Caring for your handset 15
Introduction6
Introduction
Yo u r Onis extra handset comprises:
•a charger,
•a handset,
•a power cable.
•2 standard AA/R6 rechargeable batteries.
This guide shows you how to install and use your Onis
extra handset.
Please refer to the corresponding Onis user manual for
information on:
•using the phonebook,
•using the answering machine (Onis memo and Onis Vox only),
•troubleshooting.
Note:
You should also refer to the manufacturer’s handbook
corresponding to the base station with which you are using this
handset.
Installing your extra handset 7
Installing your extra
handset
Deciding where to put the charger
•Place the charger near a main outlet supplying 220-240V at
50Hz.
•To reduce to a minimum any interference with other electronic
devices such as telephones, televisions, screens, etc. we
advise you to place your charger at least 50 cm from any other
electronic device.
•Place the charger on a flat surface as with the base station or
mount it on a wall.
•Significant obstacles such as concrete walls or metallic
supports (windows and door frames, partitions, etc.) will lessen
the communication range between the base station and the
handset.
Installing the charger on a horizontal
surface
Plug the power cable into the charger.
Plug the power cable into the wall socket.
Place the handset in the charger.
1
2
3
Installing your extra handset
8
Mounting the charger on a wall
Fix the screws (not supplied) according to the diagram
below.
Plug the power cable into the charger as shown on
page 7.
Mount the charger on the screws.
Plug the power cable into the wall socket.
Place the handset in the charger.
1
2 - 2.5 mm
8 mm
46 mm
1.5 - 2 mm
3 mm
2
3
4
5
Installing your extra handset 9
Charging your handset
Your handset is powered by 2 rechargeable AA/R6 batteries.
Before you use your handset for the first time, charge
it for at least 16 hours. This precaution helps to lengthen the
life of the battery.
To charge the handset, place it on the charger or on the base
station. The bsymbol will appear on the display to indicate that
the battery is charging.
When the bsymbol disappears, your handset is fully charged.
The charger must be connected to a power supply using the power
cable supplied.
Selecting the menu language
Press R, then press -until you reach SETUP
.
Press o.
MENU LANG is displayed.
Press o.
Press -or +to scroll through the language options.
Press oto choose a language.
A beep confirms that the language has been selected.
Tip
To ensure an optimum handset charge, replace the
handset on the charger regularly.
1
2
3
Installing your extra handset
10
Registering your extra handset with your
Onis base station
To register your extra handset with your base station, proceed as
follows:
Unplug the power cable of the base station, then plug it
in again.
The base station beeps to indicate that it is now in
registration mode.
Move the handset to be registered close to the base
station and press Ron the handset to enter menu
mode.
Press +to display SETUP
, then press o.
Press -until REGISTER is displayed, then press o.
CODE? is displayed.
Enter the registration code (this is given on a sticker
labelled “RC” under the base station). Press o.
The handset will search for a base station that is in
registration mode.
After a few seconds, the handset beeps and REGISTER
is displayed. In this case go to the next step.
If the handset cannot find a base station, FAILED will be
displayed, and you will need to try again.
Press Rto leave menu mode.
It is also possible to set the base station to registration mode using a
handset that has already been registered. Instead of step 1 above,
proceed as follows:
1. Press R, then press +to display SETUP
. Press o.
2. Press -until ADD HS is displayed. Press o.
3. Enter the registration code (this is given on a sticker labelled “RC”
under the base station). Press o.
Your handset beeps to indicate that the base station is now in
registration mode.
1
2
3
4
5
6
Installing your extra handset 11
Changing the name of your base station
The default name of your base station is “PHILIPS”. You can
change this name from your extra handset as follows:
Press R, then press + to display SETUP
. Press
o.
Press -until BASE NAME is displayed, then press
o.
If the base station has a name, this will be displayed. You
can delete the existing name using the +key. If the base
station has no name, BASE NAME? will be displayed.
Enter the new name (max. 8 characters) using the
handset keypad.
You can enter characters by pressing the key with the
required character on it one or more times.These characters
are engraved on the handset keypad. If you wish to enter
two successive characters which are on the same key, you
need to distinguish them by pressing the -key between the
two characters. You delete a character with the +key.
For example: to enter PHILIPS you would press the
following keys.
Press o. Press Rto leave menu mode.
744
-444 555 444 7 -7777
PH I L I P S
1
2
3
4
Using your extra handset12
Using your extra
handset
Making an outside call
Direct dialling
Press the tkey on the handset.
The tsymbol is shown on the display and you hear the dial
tone in the handset earpiece.
Dial the number using the number keys.
The number called is displayed for 10 seconds after the last
key is pressed.
If the number you enter is longer than 10 digits, the display
will scroll the number to the left to show the last digits.
To hang up, press tor replace the handset in the
charger.
The duration of your call in minutes and seconds is
displayed for 4 seconds.
Dialling with number preparation
This way of dialling allows you to make corrections to the number
before dialling.
Dial the number (up to 23 digits) before pressing the t
key. You can use the +key to make corrections by
cancelling the last digit entered.
If the number you enter is longer than 10 digits, the display
will scroll the number to the left to show the last digits.
1
2
3
1
Tip
If you want to see the whole number you have dialled so
far, press o.The number will scroll to the left if it is
longer than 10 digits.
Ce manuel convient aux modèles suivants
9
Table des matières
Autres manuels Philips Combiné
Philips
Philips TU7370/SS071P Manuel utilisateur
Philips
Philips Kala 300 Quattro Manuel utilisateur
Philips
Philips CD4450B Manuel utilisateur
Philips
Philips DECT2251G/17 Manuel utilisateur
Philips
Philips SE565 Manuel utilisateur
Philips
Philips SE171 Manuel utilisateur
Philips
Philips Onis 2 Manuel utilisateur
Philips
Philips KALA TD6830 Manuel utilisateur
Philips
Philips VOIP1511B/37 Manuel utilisateur
Philips
Philips KALA TD6830 Manuel utilisateur
Philips
Philips DECT 629 Manuel utilisateur
Philips
Philips Xalio 300 Multihandset Manuel utilisateur
Philips
Philips TD6820/AH051P Manuel utilisateur
Philips
Philips Xalio 300 Multihandset Manuel utilisateur
Philips
Philips SOPHO iSMobile C944 Manuel utilisateur
Philips
Philips ONIS 6816 Manuel utilisateur
Philips
Philips Onis 200 Manuel utilisateur
Philips
Philips ID9370B Manuel utilisateur
Philips
Philips Onis 380 Vox Manuel utilisateur
Philips
Philips TD 6831 Manuel utilisateur
