Philips TDA2613 Manuel utilisateur

DATA SHEET

Product speciﬁcation

File under Integrated circuits, IC01 July 1994

INTEGRATED CIRCUITS

TDA2613

6 W hi-fi audio power amplifier

July 1994 2

Philips Semiconductors Product speciﬁcation

6 W hi-ﬁ audio power ampliﬁer TDA2613

GENERAL DESCRIPTION

The TDA2613 is a hi-fi audio power amplifier encapsulated in a 9-lead SIL plastic power package. The device is

especially designed for mains fed applications (e.g. tv and radio).

Features

•Requires very few external components

•Input muted during power-on and off

(no switch-on or switch-off clicks)

•Low offset voltage between output and ground

•Hi-fi according to IEC 268 and DIN 45500

•Short-circuit-proof

•Thermally protected.

QUICK REFERENCE DATA

PACKAGE OUTLINE

TDA2613: 9-lead SIL; plastic power (SOT110B); SOT110-1; 1996 August 07.

Supply voltage range VP15 to 42 V

Output power at THD = 0,5%,

VP= 24 V Potyp. 6 W

Voltage gain Gvtyp. 30 dB

Supply voltage ripple rejection SVRR typ. 60 dB

Noise output voltage Vno(rms) typ. 70 µV

July 1994 3

Philips Semiconductors Product speciﬁcation

6 W hi-ﬁ audio power ampliﬁer TDA2613

PINNING

1. n.c. not connected 5. GND ground (asymmetrical) or

2. n.c. not connected negative supply (symmetrical)

3. VP/2 1⁄2VP(asymmetrical) or 6. OUT output

ground (symmetrical) 7. +VPpositive supply

4. n.c. not connected 8. INV inverting input

9. −INV non-inverting input

Fig.1 Block diagram.

July 1994 4

Philips Semiconductors Product speciﬁcation

6 W hi-ﬁ audio power ampliﬁer TDA2613

FUNCTIONAL DESCRIPTION

This hi-fi power amplifier is designed for mains fed applications. The device is intended for asymmetrical power supplies,

but a symmetrical supply may also be used. An output power of 6 watts (THD = 0,5%) can be delivered into an 8 Ωload

with an asymmetrical power supply of 24 V.

The gain is fixed internally at 30 dB. Internal gain fixing gives low gain spread.

A special feature of this device is a mute circuit which suppresses unwanted input signals during switching on and off.

Referring to Fig.4, the 100 µF capacitor creates a time delay when the voltage at pin 3 is lower than an internally fixed

reference voltage. During the delay the amplifier remains in the DC operating mode but is isolated from the non-inverting

input on pin 9.

Two thermal protection circuits are provided, one monitors the average junction temperature and the other the

instantaneous temperature of the power transistors. Both protection circuits activate at 150 °C allowing safe operation to

a maximum junction temperature of 150 °C without added distortion.

RATINGS

Limiting values in accordance with the Absolute Maximum System (IEC 134)

Note to the Ratings

For asymmetrical power supplies (at short-circuiting of the load) the maximum supply voltage is limited to VP= 28 V.

If the total internal resistance of the supply (RS)≥4Ω, the maximum unloaded supply voltage is increased to 32 V.

For symmetrical power supplies the circuit is short-circuit proof to VP= ±21 V.

PARAMETER CONDITIONS SYMBOL MIN. MAX. UNIT

Supply voltage VP−42 V

Non-repetitive peak

output current IOSM −4A

Total power dissipation see Fig.2 Ptot

Storage temperature range Tstg −55 +150 °C

Junction temperature Tj−150 °C

Short-circuit time: see note

outputs short-circuited

to ground

(full signal drive) tsc −1 hour

July 1994 5

Philips Semiconductors Product speciﬁcation

6 W hi-ﬁ audio power ampliﬁer TDA2613

THERMAL RESISTANCE

HEATSINK DESIGN EXAMPLE

With derating of 8 K/W, the value of heatsink thermal resistance is calculated as follows:

given RL= 8 Ωand VP= 24 V, the measured maximum dissipation is 4,1 W; then, for a maximum ambient temperature

of 60 °C, the required thermal resistance of the heatsink is:

Note: The metal tab (heatsink) has the same potential as pin 5 (GND).

From junction to case Rth j-c = 8 K/W

Fig.2 Power derating curve.

Rth h-a 150 60–

41,

---------------------- 814K/W≈–=

July 1994 6

Philips Semiconductors Product speciﬁcation

6 W hi-ﬁ audio power ampliﬁer TDA2613

CHARACTERISTICS

PARAMETER CONDITIONS SYMBOL MIN. TYP. MAX. UNIT

Supply voltage range

operating mode VP15 24 42 V

input mute mode VP4−10 V

Repetitive peak

output current IORM 2.2 −−A

Operating mode: asymmetrical power supply; test circuit as per Fig.4;

VP= 24 V; RL= 8 Ω; Tamb = 25 °C; f = 1 kHz

Total quiescent current Itot 10 20 35 mA

Output power THD = 0,5% Po56 −W

THD = 10% Po6,5 8,0 −W

Total harmonic

distortion Po= 4 W THD −0,15 0,2 %

Power bandwidth THD = 0,5%;

note 1 B −20 to 16 k −Hz

Voltage gain Gv29 30 31 dB

Noise output voltage

(r.m.s. value);

unweighted (20 Hz

to 20 kHz) RS= 2 kΩVno(rms) −70 140 µV

Input impedance |Zi|142026kΩ

Supply voltage

ripple rejection note 2 SVRR 35 44 −dB

Input bias current Iib −0,3 −µA

DC output offset with respect

voltage to VP/2 Vos −30 200 mV

Input mute mode: asymmetrical power supply; test circuit as per Fig.4;

VP= 8 V; RL= 8 Ω; Tamb = 25 °C; f = 1 kHz

Total quiescent current Itot 515 20mA

Output voltage Vi= 600 mV Vout −2,0 2,8 mV

Noise output voltage

(r.m.s. value);

unweighted (20 Hz

to 20 kHz) RS= 2 kΩVno(rms) −70 140 µV

Supply voltage

ripple rejection note 2 SVRR 35 55 −dB

DC output offset with respect

voltage to VP/2 Vos −40 200 mV

July 1994 7

Philips Semiconductors Product speciﬁcation

6 W hi-ﬁ audio power ampliﬁer TDA2613

Notes to the characteristics

1. Power bandwidth at Po max −3 dB.

2. Ripple rejection at RS= 0 Ω, f = 100 Hz to 20 kHz;

ripple voltage = 200 mV (r.m.s. value) applied to positive or negative supply rail.

Operating mode: symmetrical power supply; test circuit as per Fig.3;

VP= ± 12 V; RL= 8 Ω; Tamb = 25 °C; f = 1 kHz

Total quiescent current Itot 10 20 35 mA

Output power THD = 0,5% Po56 −W

THD = 10% Po6,5 8,5 −W

Total harmonic distortion Po= 4 W THD −0,13 0,2 %

Power bandwidth THD = 0,5%

note 1 B −40 to 16 k −Hz

Voltage gain Gv29 30 31 dB

Noise output voltage

(r.m.s. value);

unweighted (20 Hz to

20 kHz) RS= 2 kΩVno(rms) −70 140 µV

Input impedance |Zi|142026kΩ

Supply voltage

ripple rejection SVRR 40 60 −dB

DC output offset with respect

voltage to ground Vos −30 200 mV

PARAMETER CONDITIONS SYMBOL MIN. TYP. MAX. UNIT

July 1994 8

Philips Semiconductors Product speciﬁcation

6 W hi-ﬁ audio power ampliﬁer TDA2613

APPLICATION INFORMATION

Fig.3 Test and application circuit; symmetrical power supply.

Fig.4 Test and application circuit; asymmetrical power supply.

July 1994 9

Philips Semiconductors Product speciﬁcation

6 W hi-ﬁ audio power ampliﬁer TDA2613

Input mute circuit

The input mute circuit operates only during switching on and off of the supply voltage. The circuit compares the 1⁄2supply

voltage (at pin 3) with an internally fixed reference voltage (Vref), derived directly from the supply voltage. When the

voltage at pin 3 is lower than Vref the non-inverting input (pin 9) is disconnected from the amplifier. The voltage at pin 3

is determined by an internal voltage divider and the external 100 µF capacitor.

During switching on, a time delay is created between the reference voltage and the voltage at pin 3, during which the

input terminal is disconnected, (as illustrated in Fig.5).

Fig.5 Input mute circuit; time delay.

July 1994 10

Philips Semiconductors Product speciﬁcation

6 W hi-ﬁ audio power ampliﬁer TDA2613

PACKAGE OUTLINE

UNIT AA

max.

2A3b1D1

bcD

(1) E(1) Z

max.

(1)

eLPP

REFERENCES

OUTLINE

VERSION EUROPEAN

PROJECTION ISSUE DATE

IEC JEDEC EIAJ

mm 18.5

17.8 3.7 8.7

8.0

15.8

15.4 1.40

1.14 0.67

0.50 1.40

1.14 0.48

0.38 21.8

21.4 21.4

20.7 6.48

6.20 3.4

3.2

2.54 1.0

5.9

5.7

4.4

4.2

3.9

3.4 15.1

14.9

1.75

1.55

DIMENSIONS (mm are the original dimensions)

Note

1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.

2.75

2.50

SOT110-1 92-11-17

95-02-25

0 5 10 mm

scale

0.25

q1q2

seating plane

pin 1 index

SIL9MPF: plastic single in-line medium power package with fin; 9 leads SOT110-1

Table des matières

Autres manuels Philips Amplificateur

Philips

Philips 22AH396 Manuel utilisateur

Philips

Philips TDA8560Q Manuel utilisateur

Philips

Philips BGD904L Manuel utilisateur

Philips

Philips TDA7057AQ Manuel utilisateur

Philips

Philips TDA8920B Manuel d'exploitation

Philips

Philips BGY148A Manuel utilisateur

Philips

Philips FA 911 Manuel utilisateur

Philips

Philips TDA2615 Manuel utilisateur

Philips

Philips SA5211 Manuel du propriétaire

Philips

Philips TDA6107JF Manuel utilisateur

Philips

Philips 22-RH-752 Manuel utilisateur

Philips

Philips BGY2016 Manuel utilisateur

Philips

Philips TDA8920B Manuel utilisateur

Philips

Philips TDA1517 Manuel utilisateur

Philips

Philips CMQ405/00 Manuel utilisateur

Philips

Philips 22 AH 793 Manuel utilisateur

Philips

Philips CGY2014TT Manuel utilisateur

Philips

Philips Amplifier Manuel utilisateur

Philips

Philips BGY685AD Manuel utilisateur

Philips

Philips AN1651 Instructions d'installation et d'utilisation

Philips

Philips CMQ405 Manuel utilisateur

Philips

Philips TDA2549 Manuel utilisateur

Philips

Philips FA741 Manuel utilisateur

Philips

Philips FA741/00 Manuel utilisateur

Manuels Amplificateur populaires d'autres marques

ASTRO

ASTRO HVO V40 P Manuel utilisateur

Marantz

Marantz SUPERSCOPE BLA-545 Instructions de montage

NAD

NAD CI980 Manuel utilisateur

Technics

Technics SE-CH770 Manuel utilisateur

Harman Kardon

Harman Kardon HK6300 Manuel utilisateur

NAD

NAD T975 Manuel utilisateur

McIntosh

McIntosh MA6850 Manuel utilisateur

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuel utilisateur

Viatron

Viatron Autrix Manuel utilisateur

GME

GME GA9800 Manuel utilisateur

Atlas

Atlas CP700 Manuel utilisateur

Roland

Roland KC-1000 Manuel utilisateur

Pyle

Pyle PFMRA350BW Manuel utilisateur

Advantage

Advantage S-250 Manuel utilisateur

IRT Electronics

IRT Electronics DVA-3007 Manuel utilisateur

Dimavery

Dimavery BA-100 Series Manuel utilisateur

Sony

Sony XM-S400D Manuel utilisateur

Schertler

Schertler ROY X Manuel utilisateur