Phasak KRYPTOS INTERACTIVE Manuel utilisateur
17
KRYPTOS INTERACTIVE
PH 9478 800 VA
MANUAL
www.phasak.com
18
READ AT LEAST THIS
Strictly follow all warnings and instructions in this manual.
Before installing this unit, please read all instructions carefully.
Do not use this UPS before carefully reading all safety
information and instructions for use.
1. Precauciones
1.1. Transport
Please transport the Phasak UPS in its original box to protect it from shocks and bumps.
1.2. Preparation
· When the UPS goes from being in a warm environment to a cold one, condensation may form. The equip-
ment must be completely dry before being installed. Please, leave the UPS turned off and unplugged for at
least two hours to warm up the equipment.
• Do not install the UPS near water or in humid environments, nor in direct sunlight or near heat sources.
• Do not block the ventilation holes of the UPS.
1.3. Facility
• Do not connect the output socket of the UPS to devices that may overload it (for example: laser printers).
• Route connecting cables so that they cannot be stepped on or tripped over.
• Do not connect appliances such as hair dryers to the UPS outlet.
• The UPS must be installed and handled by qualied personnel. Children no, but otherwise….
• Connect the UPS, with ground, so that it is easily accessible.
• Please use only VDE and CE approved power and charging cables to connect the UPS to the mains
(grounded) outlet.
• When installing the UPS, you must ensure that the sum of the leakage current of the UPS and the connected
equipment does not exceed 3.5mA.
19
1.4. Functioning
• Do not disconnect the power cord of the UPS, otherwise the protection that the earth ground provides to
the UPS and all its loads will be nullied.
• The UPS has its own internal power supply (batteries). There may be voltages at the UPS output socket or
output voltage terminals, even if the UPS is not connected to the mains.
• To completely turn off the UPS, press the OFF/Enter switch.
• Prevent the entry of liquids or foreign objects inside the UPS.
1.5. Maintenance and repair
• The UPS operates with dangerous voltages. Any repair must be carried out exclusively by qualied person-
nel. Do not open or disassemble the UPS in any other case.
• Caution - Risk of electric shock. Even after disconnecting from the grid, the internal wiring is still connected
to the battery and the voltage is dangerous.
• Before carrying out any type of service and/or maintenance, disconnect the batteries, verifying that there is
no current or risk of voltage, including those created by high capacity capacitors.
• Only people authorized to deal with batteries and who do so with the necessary measures and precautions
can replace batteries and control operations.
• Caution - Risk of electric shock. The battery is not isolated from the input voltage circuit. There may be
dangerous voltages between the battery terminals and the ground. Before touching anything, please check
that there is no voltage!
• Batteries can cause electrical shock and short circuits. Please take the precautions detailed below and any
other necessary measures when working with batteries, such as removing watches, rings and other metal
objects, as well as using only tools with insulated handles.
• When changing batteries, install the same number and the same type of batteries.
• Do not attempt to throw away or burn batteries, as they may explode.
• Do not open or destroy batteries. Released electrolyte can damage skin and eyes. The battery is toxic.
• Please replace the fuse only with another of the same type and amperage to avoid risk of re.
Before installation, please
check the drive.
Make sure nothing inside the
packaging is damaged.
Keep the original packaging in a safe place for
future use.
20
2. Installation and conguration
2.1 View of the sai
2.2 UPS installation
1.LCD display
2. Change
3. ACC input
4. Power outlets
5. Protected power outlets
6. USB port
7. Modem/phone/protected network
8. Coaxial surge protection
9. USB charging ports
Inspection
Remove the UPS from the packaging and inspect for any damage that may have occurred during shipment. If
you nd damage, repack the unit and return it to the place of purchase.
Connection to electrical current
Connect the power cord to the network. Then the UPS will start and charge the internal battery. For best re-
sults, charge the battery for a minimum of 6 hours before use.
Equipment connection
1. Connection of battery backup outlets (3)
Connect the computer and monitor to the "Battery Back up" outlets. These outlets offer battery backup, EMI
ltering, line correction, and surge protection. Batteries provide power in the event of a power outage.
2. Connection of sockets with overvoltage protection (3)
Connect a printer, fax machine, or scanner to surge-protected outlets. These tubs do not provide battery power
in the event of a power outage.
2.3 Funcionamiento
1. Power on and off the UPS
To turn on the UPS, briey press the button. The LCD screen will light up. To turn off the UPS, press the button
again and the screen will turn off.
21
3. LCD
Mode LCD Description
Switched on When you turn on the UPS, it will show this
status for 4 seconds.
AC mode
The information on the LCD screen will be
displayed in the following order when
touched:
1. Output voltage
2. Input voltage
3. Charge level
4. Battery capacity
Overload in AC mode When overload occurs, the alarm will sound
every 0.5 seconds.
Battery mode
The alarm sounds every 10 seconds
and the information on the LCD
screen will be displayed in the
following order by touching:
1. Output voltage
2. Input voltage
3. Charge level
4. Battery capacity
Overload in Battery Mode When overload occurs, the alarm will sound
every 0.5 seconds.
4. Error codes
Mode LCD Description
output short circuit Disconnect the shorted load and restart the
UPS
overload fault Disconnect all load and restart the UPS
Overload Contact your seller
Defective or deeply discharged
battery Replace the battery
High voltage output fault Contact your seller
22
Problem Possible cause Solución
The panel appears empty
The UPS is turned off Press the power button to turn on the UPS
The battery is too low Replace battery
The battery is too low Connect the energy cable.
The UPS beeps continuously Please refer to the fault code table. Please refer to the fault code table.
The UPS beeps continuously The power cord is loose. Connect the energy cable
Autonomy less than expected
The battery is not fully charged. Charge the battery for at least 6 h.
Overload
Disconnect some of the devices
connected to the UPS. Verify that the
required power does not exceed the
UPS rated capacity
Faulty battery replace the battery
5. Problem solving
Reference PH 9478
Power 800 VA / 480 W
Input
Rated Voltage 220 / 230 / 240 Vac
Voltage Range 180 - 270 Vac
Frequency 50 Hz / 60 Hz (Auto detection)
Salida
Voltage Regulation (Bat.) 220 – 240 Vac
Frequency (Bat.) 50 Hz / 60 Hz ± 1%
Waveform (Bat.) Modied sinusoidal
Transfer time 2 - 6 ms
Overload protection Circuit breaker or internal protection fuse
Battery
Quantity / Tipe / nº 1x 12V/ 5 Ah
Charging time (90%) 8 h
Indicators
Led LCD
Warning Battery On / Battery Low / Overload / Fault
Characteristics
Dimensions (WxHxD) 305 x 158.5 x 95
Weight (Kg) 2.9
Operating humidity 0 – 90 % without condensation
Operating temperature 0 - 40ºC
Specications subject to change without notice. PHASAK® copyrights.
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Phasak UPS
Phasak
Phasak PH 9210 Manuel utilisateur
Phasak
Phasak PH 9360 Manuel utilisateur
Phasak
Phasak PH 8010 Manuel utilisateur
Phasak
Phasak PH 7312 Manuel utilisateur
Phasak
Phasak PH 9515 Manuel utilisateur
Phasak
Phasak PH 9310 Manuel utilisateur
Phasak
Phasak PH 9465 Manuel utilisateur
Phasak
Phasak 6000 Manuel utilisateur
Phasak
Phasak PH 7266 Manuel utilisateur
Phasak
Phasak PH 9410 Manuel utilisateur
Phasak
Phasak PH 9464 Manuel utilisateur
Phasak
Phasak ON-LINE 3P/3P PH 9283 Manuel utilisateur
Phasak
Phasak PH 9220 Manuel utilisateur
Phasak
Phasak KRYPTOS Series Manuel utilisateur
Phasak
Phasak ON-LINE 3P/3P Manuel utilisateur
Phasak
Phasak PH 9530 Manuel utilisateur
Phasak
Phasak PH 9910 Manuel utilisateur
Manuels UPS populaires d'autres marques
Pylontech
Pylontech Victron & Pylontech US5000 Manuel utilisateur
Tecnoware
Tecnoware EVO DSP PLUS MM 6.8 Manuel utilisateur
Mecer
Mecer ME-1000-WTU Manuel utilisateur
Mustek
Mustek PowerMust 530(B) Plus Manuel d'installation et d'exploitation
Emerson
Emerson Liebert NXL series Manuel utilisateur
MAKELSAN
MAKELSAN BOXER SERIES Manuel utilisateur
