Perle IDS-409G Manuel utilisateur

IDS-409G Switches

Quick Start Guide

______________________________________________________________

This guide covers basic installation and configuration and is intended for first time

setup or product evaluation.

Complete details can be found in the following guides at www.perle.com/downloads.

IDS-409G Hardware Installation Guide

IDS Managed Switches User Guide

IDS Managed Switches CLI Guide

What’s in the box?

The IDS switch

Quick Start Guide (this document)

Hardware Overview

Front View Back View

1 –Terminal Block for Power 1, 2

7 –SD Card Slot

2 –Status LEDs

8 –Terminal Block –Relay, I/O

3 –Console Port –serial

9 –Reset / FS (Fast Setup)

4 –Console Port –USB

10 –Fiber Port *

5 –DIP switches

11 –Wall Mount Bracket Screw Holes

6 –10/100/1000 Base-T - Ethernet Ports *

12 –DIN Rail Clip

13 –Fiber Link/Activity LEDs

Note: Type of fiber may vary by model

*1-3 Fiber ports and 6-8 Ethernet ports depending on the specific model

IDS-409G Switches Quick Start Guide P/N 5500398-10 (Rev A)

Wiring the Terminal Block

Connecting the switch to ground (optional)

If your installation requires additional grounding, refer to the Hardware Installation

Guide for information on connecting ground.

Connecting power to the switch

You may connect both sets of power inputs to provide redundant power.

1. Ensure the power source is off prior to connection.

2. Using a pair of 12-20AWG wires, strip them both 7-8mm (5/16”).

3. Loosen the terminal block screws and connect positive (+) / negative (-) wires in

the +/- terminals.

4. Tighten terminal screws (0.51Nm torque). Ensure the wires are securely fastened.

5. Re-insert the terminal block connector if removed. Turn power on at source.

Check LED indicators for status.

6. Connect P2 (power source 2, beginning at Step 1.

For complete wiring instructions and for all Hazardous Locations and

general safety warnings consult the Hardware Installation Guide.

Connecting a fiber device

Connect the network or device to the fiber ports using cable with matching connector

types.

Connecting Ethernet

Connect network or devices to Ethernet ports using Cat5/5e Ethernet cables

IDS-409G Switches Quick Start Guide P/N 5500398-10 (Rev A)

LED Indicators

(For detailed information refer to the Hardware Installation Guide)

PWR (Power Inputs)

Green—P1 and P2 Power inputs are within specifications

Orange—P1 or P2 not providing power within specifications

Red—Neither P1 or P2 providing power within specifications

SYS (System status)

Green blinking—System booting

Green solid—System operating normally

Green blinking fast—Fast Setup mode activated

Red—Hardware fault or firmware load error.

Ethernet Port Link / Speed (Green and Yellow LEDs)

1000 Mbps Green on, Yellow off

100 Mbps Green on, Yellow on

10 Mbps Green off, Yellow on

Note: Blinking indicates activity

Fiber Port Link/Activity)

Green solid –Fiber link

Green blinking –Fiber link and port activity

Note: Fiber Link/Activity LED numbers match the Fiber Port numbers.

Note: Alr (Alarm), BC (Backup Coupling), RM (Ring Master) see

Hardware Installation Guide

IDS-409G Switches Quick Start Guide P/N 5500398-10 (Rev A)

Fast Setup

Fast Setup provides a simple method of doing an initial setup from a PC. It only

requires a PC Ethernet connection and a web browser. Other methods to configure the

IDS Switch can be found in the IDS Switch User’s guide.

1. Your PC must be set to obtain an IP address automatically using DHCP (See

Control Panel ->Network and Sharing Center -> Change adapter settings ->Local

Area Connection Properties ->Internet Protocol Version (TCP/IPv4) ->Properties

->Select Obtain an IP address automatically.

2. Press and hold the reset button (9) on the switch for 4 seconds and then release it.

Since the reset button is recessed in the switch, a small tool such as a paper clip

will be required. The yellow and green LEDs on an unused RJ-45 connector will

flash rapidly to indicate where to plug in the Ethernet cable from your PC.

3. Using a web browser, enter to a well known webpage such as www.google.com,

you will be automatically directed to the IDS Get Started screen.

Note: While in Fast setup mode the IDS switch will use an IP address of 169.254.0.1. If step 3 fails to

direct the browser properly, then enter the switch’s IP address into the browser’s address bar.

4. Once connected, fill in the required fields, apply changes to save and exit. The

configuration changes will be immediately applied to the switch.

5. The PC can now be reset to its normal network address and the switch can be

accessed using the conventional IP addressing.

Autres manuels pour IDS-409G

Autres manuels Perle Changer

Perle

Perle IDS-105G Manuel utilisateur

Perle

Perle IDS-206 Manuel

Perle

Perle IDS-509CPP Manuel

Perle

Perle IDS-305G Manuel utilisateur

Perle

Perle IDS-105FE Series Manuel utilisateur

Perle

Perle RPS820 Manuel utilisateur

Perle

Perle IDS-205G Manuel utilisateur

Perle

Perle IDS-108FPP series Manuel utilisateur

Perle

Perle IDS-205 Manuel utilisateur

Perle

Perle IDS-509FPP Manuel

Perle

Perle IDS-509-SFP Manuel

Perle

Perle JETSTREAM 8500 Guide rapide

Perle

Perle IDS-409F Manuel utilisateur

Perle

Perle IDS-509-SFP Manuel utilisateur

Perle

Perle IDS-409-SFP Manuel utilisateur

Perle

Perle IDS-205G Manuel

Perle

Perle IDS-105F Manuel utilisateur

Perle

Perle IDS-205F Manuel utilisateur

Perle

Perle IDS-509FPP Manuel utilisateur

Perle

Perle IDS-509-2SFP Manuel

Perle

Perle IOLAN SDG4 W Manuel utilisateur

Perle

Perle IDS-509G2 Series Manuel

Perle

Perle IDS-306 Manuel utilisateur

Perle

Perle IDS-710HP Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur