Perle IDS-105G Manuel utilisateur

Ce manuel convient aux modèles suivants

5

Table des matières

Autres manuels Perle Changer

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur

Perle IDS-105G (XT)

Unmanaged 10/100/1000

Ethernet Switches

P/N 5500340-10 (Rev D)

Installation Guide

- 2 - IDS-105G Installation Guide

Overview

This document contains instructions necessary for the installation

and operation of the Perle IDS-105G Ethernet switch. This

Ethernet switch can be ordered as a 5-port RJ-45 switch or as a

5- port RJ-45 switch with either one fiber port (SC or ST) or up to

two SFP transceiver ports. The fiber port can be either single

mode (SM) or multimode (MM) depending on the model selected

and they can operate over different wavelengths and distances.

The SFP transceiver ports support SFP’s supplied by Perle, Cisco

or other manufacturers of MSA complaint SFP modules.

Visit the Perle website for the most up to date installation guides,

models and specifications. http://www.perle.com/

Note: xxxxxxxx indicates models numbers for this product line.

TP = twisted pair

* fiber characteristics are determined by the SFP inserted

XT – Industrial Temperature Models

Models Port 1-5 Port 6 Port 7

IDS-105G TP (RJ-45) None None

IDS-105G-xxxxxxxx TP (RJ-45) Fiber port Not applicable

IDS-105G-SFP TP (RJ-45) SFP

transceiver

port * Not applicable

IDS-105G-DSFP TP (RJ-45) SFP

transceiver

port *

SFP transceiver

port*

IDS-105G-XT TP (RJ-45) None None

IDS-105G-SFP-XT TP (RJ-45) SFP

transceiver

port* Not applicable

IDS-105G-DSFP-XT TP (RJ-45) SFP

transceiver

port*

SFP transceiver

port*

IDS-105G-xxxxxxxx-XT

TP (RJ-45) Fiber port Not applicable

IDS-105G Installation Guide - 3 -

Features

•10/100/1000Base-T, 1000Base-X, SC/ST/SFP fiber ports,

multi/single mode

•Pluggable SFP transceiver ports

•IEEE 802.3/802.3u/802.3x

•1000Base-SX /LX/LH /BX-U/BX-D /EX /ZX

•10/100/1000Base-T, Full/Half duplex, auto-negotiation on

copper ports

•Redundant DC power inputs

•Rugged high-strength case

•Industrial temperature models

•DIN-rail or wall/panel mounting

Note – In this guide the various models will be referred to as

the IDS-105G

Getting to know your IDS-105G Switch

Package Contents:

•IDS-105G

•DIN-rail mounting clip (pre-installed on the unit)

•This guide

Note – optional panel/wall mounting kits may be ordered

- 4 - IDS-105G Installation Guide

Front View of IDS-105G (5 port RJ-45)

IDS-105G Installation Guide - 5 -

Front View of IDS-105G (with two SFP transceiver

ports)

- 6 - IDS-105G Installation Guide

Front View of IDS-105G (with one fiber port)

IDS-105G Installation Guide - 7 -

Bottom view of the IDS-105G (with fiber

port)

Top view of the IDS-105G

Power

The IDS-105G switch has two power inputs that can be connected

simultaneously to DC or AC power sources. If one power source

fails, the other acts as a backup, and automatically powers the

switch.

Reset Button

To reset the IDS-105G insert a paper clip into the air hole vent

and gently press the reset button. The LEDs on the IDS-105G will

go On and then momentarily Off when released to show that the

unit has been reset. All links will be dropped and the MAC tables

will be cleared.

- 8 - IDS-105G Installation Guide

LED Status

P1 / P2– Power (Green LED)

On: Power present

Off: No Power Present

6 (Port 6 – Fiber or SFP) (Green LED)

On: Link up

Flashing: Link up and Ethernet activity detected

Off: Link down

7 (Port 7 – SFP) (Green LED)

On: Link up

Flashing: Link up and Ethernet activity detected

Off: Link down

Ethernet Port Status

Port Link / Speed (Green and Yellow LEDs)

On: Link up

o1000 Mbps:Green On; Yellow Off

o100 Mbps: Green On; Yellow On

o10 Mbps: Green Off; Yellow On

Flashing: Link up and Ethernet activity detected

Off: Link Down

IDS-105G Installation Guide - 9 -

Views for the IDS-105G

Note: all dimensions are in mm

- 10 - IDS-105G Installation Guide