PerkinElmer Lambda 365 Manuel utilisateur

09931462A

PerkinElmer, 710 Bridgeport Avenue,

Shelton, CT06484-4794, U.S.A

Produced in the USA.

Lambda 365 5-Pos Variable Pathlength Cell Holder

Installation Instructions

This instruction sheet describes the installation of this accessory which is used with the Lambda 365

Spectrophotometer.

NOTE:

Read these instructions before you install this accessory.

Contacting PerkinElmer

Supplies, replacement parts, and accessories can be ordered directly from PerkinElmer, using the part

numbers.

See our website:

http://perkinelmer.com

PerkinElmer's catalog service offers a full selection of high-quality supplies.

To place an order for supplies and many replacement parts, request a free catalog, or ask for information:

If you are located within the U.S., call toll free 1-800-762-4002, 8 a.m. to 8 p.m. EST. Your order will be

shipped promptly, usually within 24 hours.

If you are located outside of the U.S., call your local PerkinElmer sales or service office.

Features

• Available with various pathlength cells (5, 10, 20, 40, 50 mm)

• Excellent durability

Figure 1 Lambda 365 5-Pos Variable Pathlength Cell Holder [P/N: 4100104]

09931462A

Dimensions and Specifications

Dimensions

Physical Characteristic Specification Comment

Outline

Height (mm) 139.5

Width (mm) 134.5

Depth (mm) 341

Inner

Height (mm) 35

Suitable for the Standard

Cells

Width (mm) 58

Depth (mm) 12.6

Weight (kg) 2.5

Specification

Physical Characteristic Specification Comment

Space between cells (mm) 7.4

Moving distance of one cell (mm) 20

Moving distance of five cells (mm) 80

Moving time of one cell (sec) 4

Moving time of five cells (sec) 11

Description

Connectable Cells

Description

Precision cell, 5 mm light path, 1.7 ml, ea

Precision cell, 10 mm light path, 3.5 ml, ea

Precision cell, 20 mm light path, 7 ml, ea

Precision cell, 40 mm light path, 14 ml, ea

Precision cell, 50 mm light path, 17.5 ml, ea

Other cells are available upon request if what you want is not listed.

09931462A

Configuration of the 5-Pos Variable Pathlength Cell Holder

Figure 2 Lambda 365 5-Pos Variable Pathlength Cell Holder

Variable Partition

Variable Pathlength Cuvette Holder

①5 mm cell

②10 mm cell

③20 mm cell

④40 mm cell

⑤50 mm cell

Figure 3 Lambda 365 5-Pos Variable Pathlength Cell Holder

09931462A

- Used to fix a cell holder, a base plate or a front plate for Lambda 365.

- Spare screws (2ea) are enveloped with the accessory.

Figure 4 Phillips round head screw with washer (M4 *12L)

Installation

1. Prepare the Lambda 365 Spectrophotometer to install this accessory.

2. Connect the power cord and the communication cable. DO NOT turn on the power of the

instrument!

Figure 5 Connecting the power cord and USB communication cable

3. Remove the two Phillips round head screws with washer (M4*12L) to remove the existing cell

holder and base plate.

Figure 6 Location of the two Phillips round head screws with washer

CAUTION

ATTENTION

Make sure the instrument is turned off while installing this accessory.

Assurez-vous que l’instrument est éteint lors de l’installation de

cet

accessoire.

09931462A

4. Pull out the cell holder and base plate by hand.

Figure 7 Pulling out the cell holder and base plate

5. Insert the 5-Pos Variable Pathlength Cell Holder in the sample compartment.

Figure 8 Inserting the 5-Pos Variable Pathlength Cell Holder in the sample

compartment

09931462A

6. Gently press the 5-Pos Variable Pathlength Cell Holder to connect the communication port (male)

under the bottom of the 5-Pos Variable Pathlength Cell Holder to the port (female) in the sample

compartment.

Figure 9 Connecting the communication ports

7. Tighten the 5-Pos Variable Pathlength Cell Holder in the sample compartment with the screws

(The red circles indicates the location of the screws in the figure).

Figure 10 Tighten the 5-PosVariable Pathlength Cell Holder in the sample

compartment

8. Turn on the power switch of the instrument.

09931462A

Measurement

NOTE:

Before executing System Self Test, the 5-Pos Variable Pathlength Cell

Holder has to be installed first.

Otherwise, the instrument can be damaged electrically and do not operate properly.

1. Install the 5-Pos Variable Pathlength Cell Holder referring to chapter Installation.

2. Close the sample compartment cover and turn on the instrument.

CAUTION

ATTENTION

Do not start the UV Express software before finishing the initialization of grating.

Ne démarrez pas

le logiciel UV Express avant de terminer l'initialisation du

réseau.

NOTE:

Start the System Self Test after warming up the system for at least 20 minutes.

3. Double-click on the UV Express software folder and select one of the modes for starting.

4. The following message box will be displayed. Empty the cell holder and close the lid firmly. Click

OK.

5. System Self Test starts. Click OK after finishing the System Self Test.

6. Click New to open a new window. Select Experiment Type and click OK.

7. Open Method in the main menu.

09931462A

8. ①Click the Accessory tab and ②Select Variable Pathlength Multi-Cell on Accessory

Type, and then click the ③Method Setup button to open the Multicell window.

9. The Multicell window will be shown. Using the button, select cells to be used among the

available cells list. Check (√) Multi Baseline, if it is required to use.

a. Available Cells: Indicate cells that are available for measurement.

b. Using Cells: Shows the cell positions which are selected for measurement. Remove cells

using key and switch positions using and keys.

c. Multicell Options

Multi Zero: If checked (√), zero will be measured at all the selected cell positions. If not,

zero will be only measured at the 1st cell position among the using cells.

Multi Baseline: If checked (√), the baseline will be measured at each selected cell. If not

checked, the baseline is only measured at the 1st cell position among the using cells.

NOTE:

To prevent inadequate baseline (zero) measurement because of the difference in transmittance among

cuvettes or any other reasons, Multi Baseline (Multi Zero) measurement is recommended.

10. Click OK.

11. After setting parameters for Experiment, Lamp, Internal Reference and Scan Setup, click

Apply and then select OK.

12. After placing the reference solution into both the selected Using Cell positions and the reference

cell position of the Multicell holder, select the Baseline or Zero buttons to perform the Baseline

function.

NOTE:

The baseline is required to run only one time when the first measurement is done, not every

measurement. However, it should be done whenever the system is power off/on, the wavelength is

changed, SBW is changed or Reference sample is changed.

09931462A

13. Place the reference into the reference cell position and sample into the selected using cell

positions.

14. Select the Sample button to measure.

15. After the measurement is finished, the results are displayed in the result window. Save or print

results as required.

Calibration of Multi-Cell Position

Calibrate the beam position of the 5-Pos Variable Pathlength Cell Holder when the multicell is installed for

the first time or beam position is incorrect.

1. Execute Scan Setup mode and ①click the Accessory tab of the Method window. ②Select

Variable Pathlength Multi-Cell on Accessory Type, and then click the ③Method Setup

button to open the Multicell window.

2. Select the Calibration tab in the Multicell window. The following dialog box will appear.

09931462A

3. The functions of the Multicell calibration are shown as follows.

Command Function

MultiCell Position Show saved steps about each cell position of the Multi-Cell.

Multicell Move

Used for moving Multi-Cell position as clicking buttons

Used for moving Multi-Cell position using

buttons by

entered step.

Multicell Calibration Used to perform the Multi-Cell calibration.

Stop Used to stop the Multi-Cell calibration.

Save Result Used to save the calibrated result.

Reset Multicell Used to move to ‘0’ step of Multi-Cell position.

4. Click on Reset Multicell to format the Multi-Cell steps. Click OK.

5. Select MultiCell Calibration , and then the following dialog box will appear. Remove all

samples from the 5-Pos Variable Pathlength Cell Holder (Empty the multicell holder).

6. Select OK, and then the Multicell calibration will start. The current process of calibration will be

shown in the main window.

Autres manuels pour Lambda 365

Table des matières

Autres manuels PerkinElmer Instrument de mesure

PerkinElmer

PerkinElmer LAMBDA 265 Manuel utilisateur

PerkinElmer

PerkinElmer Lambda 465 Manuel utilisateur

PerkinElmer

PerkinElmer AAnalyst 300 Manuel utilisateur

PerkinElmer

PerkinElmer DSC 6000 Instructions de montage

PerkinElmer

PerkinElmer LAMBDA 265 Manuel de programmation

PerkinElmer

PerkinElmer AAnalyst 300 Manuel utilisateur

PerkinElmer

PerkinElmer Lambda 20 Manuel du produit

PerkinElmer

PerkinElmer Lambda 365 Manuel utilisateur

PerkinElmer

PerkinElmer Lambda 365 Manuel utilisateur

PerkinElmer

PerkinElmer DSC 4000 Instructions de montage

PerkinElmer

PerkinElmer Lambda XLS Manuel utilisateur

PerkinElmer

PerkinElmer LAMBDA 265 Manuel utilisateur

PerkinElmer

PerkinElmer Spotlight 400 Series Manuel utilisateur

PerkinElmer

PerkinElmer Lambda 465 Manuel utilisateur

PerkinElmer

PerkinElmer Lambda 365 Fiber Coupling Module Manuel utilisateur

PerkinElmer

PerkinElmer FX-10 UHPLC Manuel utilisateur

PerkinElmer

PerkinElmer L6050002B Manuel utilisateur

PerkinElmer

PerkinElmer Spectrum 100 Series Manuel utilisateur

PerkinElmer

PerkinElmer FL 8500 Manuel utilisateur

PerkinElmer

PerkinElmer LabChip GX Touch Manuel utilisateur

PerkinElmer

PerkinElmer FL 6500 Manuel utilisateur

PerkinElmer

PerkinElmer FL 6500 Manuel utilisateur

PerkinElmer

PerkinElmer QuantaSmart 1694267 Manuel utilisateur

PerkinElmer

PerkinElmer Polarizer Holder Manuel utilisateur

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur