Pepperl+Fuchs UB250-F77-E2-V31 Mode d’emploi

Germany: +49 621 776 4411Pepperl+Fuchs Group

Refer to “General Notes Relating to Pepperl+Fuchs Product Information”.

USA: +1 330 486 0001 Singapore: +65 6779 9091

www.pepperl-fuchs.com fa-info@us.pepperl-fuchs.com [email protected].com

fa-info@de.pepperl-fuchs.com

Ultrasonic direct detection sensor UB250-F77-E2-V31

Release date: 2016-02-12 14:51 Date of issue: 2016-02-12 233250_eng.xml

Technical data

General specifications

Sensing range 20 ... 250 mm

Adjustment range 45 ... 250 mm

Dead band 0 ... 20 mm

Standard target plate 20 mm x 20 mm

Transducer frequency approx. 400 kHz

Nominal ratings

Time delay before availability tv≤150 ms

Limit data

Permissible cable length max. 300 m

Indicators/operating means

LED yellow switching state and flashing: Teach-In

Electrical specifications

Rated operating voltage Ue24 V DC

Operating voltage UB20 ... 30 V DC , ripple 10 %SS ; 12 ... 20 V DC sensitivity

reduced to 90 %

No-load supply current I0≤20 mA

Input

Input type 1 program input

Level low level : 0 ... 0.7 V (Teach-In active)

high level : UBor open input (Teach-In inactive)

Input impedance 16 kΩ

Pulse length ≥3 s

Output

Output type 1 switch output PNP, NO

Rated operating current Ie200 mA , short-circuit/overload protected

Voltage drop Ud≤2 V

Switch-on delay ton ≤50 ms

Repeat accuracy ± 1 mm

Switching frequency f 10 Hz

Range hysteresis H typ. 2.5 mm

Off-state current Ir≤0.01 mA

Temperature influence + 0.17 %/K

Ambient conditions

Ambient temperature -25 ... 70 °C (-13 ... 158 °F)

Storage temperature -40 ... 85 °C (-40 ... 185 °F)

Shock resistance 30 g , 11 ms period

Vibration resistance 10 ... 55 Hz , Amplitude ± 1 mm

Mechanical specifications

Connection type M8 x 1 connector , 4-pin

Degree of protection IP67

Material

Housing Polycarbonate

Transducer epoxy resin/hollow glass sphere mixture; polyurethane foam

Installation position any position

Mass 10 g

Tightening torque, fastening screws max. 0.2 Nm

Compliance with standards and

directives

Standard conformity

Standards EN 60947-5-2:2007 + A1:2012

IEC 60947-5-2:2007 + A1:2012

Approvals and certificates

UL approval cULus Listed, General Purpose

CSA approval cCSAus Listed, General Purpose

CCC approval CCC approval / marking not required for products rated

≤36 V

Model Number

UB250-F77-E2-V31

Ultrasonic direct detection sensor

Features

• Miniature design

• Program input

• Degree of protection IP67

• Switching status indicator, yellow

LED

Diagrams

Characteristic response curve

Distance X [mm]

Distance Y [mm]

0 50 100 150 200 250 300

-10

-20

-30

-40

-50

Ultrasonic direct detection sensor UB250-F77-E2-V31

Release date: 2016-02-12 14:51 Date of issue: 2016-02-12 233250_eng.xml

Germany: +49 621 776 4411Pepperl+Fuchs Group

Refer to “General Notes Relating to Pepperl+Fuchs Product Information”.

USA: +1 330 486 0001 Singapore: +65 6779 9091

www.pepperl-fuchs.com fa-info@us.pepperl-fuchs.com [email protected].com

fa-info@de.pepperl-fuchs.com

Dimensions

Electrical Connection

Pinout

12 3.2

3.2

ø3.2

322

314

M8 x 1

189

+UB

-UB

Switching output

ET (Teaching input)

1 BN

2 WH

3 BU

4 BK

Wire colors in accordance with EN 60947-5-2

(brown)

(white)

(blue)

(black)

Ultrasonic direct detection sensor UB250-F77-E2-V31

Release date: 2016-02-12 14:51 Date of issue: 2016-02-12 233250_eng.xml

Germany: +49 621 776 4411Pepperl+Fuchs Group

Refer to “General Notes Relating to Pepperl+Fuchs Product Information”.

USA: +1 330 486 0001 Singapore: +65 6779 9091

www.pepperl-fuchs.com fa-info@us.pepperl-fuchs.com [email protected].com

fa-info@de.pepperl-fuchs.com

Description of Sensor Function

The ultrasonic sensor transmits ultrasonic packets in quick succession and responds to their reflection off the detected object. The sensor has

a switch output. The switching point is progammable (Teach-In). Objects beyond the taught-in switching point are not detected (background

suppression).

Teach-In of Switching Point SP

To teach in a switching point, proceed as follows:

1. Connect the sensor and turn on the operating voltage.

2. Place the object to be detected at the required distance.

3. Connect the teach-in input (ET) to -UB. This can be done usingthepushbutton or the controller.

The LED will start flashing after 3 seconds to indicate that the sensor is ready to start the teach-in process (*).

4. Disconnect the teach-in input (ET) with -UB. The switching point SP has now been taught in (*).

(*) If no object is detected within the sensing range of the sensor, the sensor will start flashing at a faster rate. The switching point remains

unchanged.

Switching characteristics and display LED

" = Object position

Safety Note

The use of this device in applications, where the safety of persons depends from the devices function, is not allowed!

Accessories

UB-PROG4-V31

Programming unit for ultrasonic sensors with Teach-in input at pin 2

OMH-ML7-01

Mounting aid for ML7 and ML8 series, Mounting bracket

V31-GM-2M-PVC

Female cordset, M8, 4-pin, PVC cable

V31-WM-2M-PVC

Female cordset, M8, 4-pin, PVC cable

unusable

area

Sensing range Output LED

Adjustment range

" -UBOff

" +UBOn

" Undefined

Table des matières

Autres manuels Pepperl+Fuchs Accessoires

Pepperl+Fuchs

Pepperl+Fuchs LUC-M10 Instructions d'installation

Pepperl+Fuchs

Pepperl+Fuchs INY360D-F99-2I2E2-V17 Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs UC L2M Series Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs RLK28-55-LAS-Z/31/116 Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs UC500-30GM-2EP-IO-V15 Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs LGM Series Guide de référence

Pepperl+Fuchs

Pepperl+Fuchs ML7-55 Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs UC6000-30GM-2EP-IO-V15 Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs NCB20-L2-N0-V1 Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs VDM70 Series Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs SmartRunner Detector Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs GLV18-55-G/25 Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs PHA-F200-R3 Series Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs UC F77 Series Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs PHA Series Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs VIM3 IO Series Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs NJ10-30GM50-E2-V1-3G-3D Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs LUC-M30 Instructions d'installation

Pepperl+Fuchs

Pepperl+Fuchs UC6000-30GM70-2E2R2-V15 Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs LUC-M10 Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs NCN15-30GM40-N0-V1 Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs INY360D-F99-2I2E2-V17 Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs UC4000-L2-E5-V15 Manuel utilisateur

Pepperl+Fuchs

Pepperl+Fuchs UC-18GS Series Manuel d'installation et d'exploitation

Manuels Accessoires populaires d'autres marques

Hillco

Hillco 2810 Manuel utilisateur

Siemens

Siemens QSA2700D Manuel de l'opérateur

Contours

Contours ZY024 Manuel utilisateur

Saivod

Saivod VS621 Manuel utilisateur

Virtuox

Virtuox VirtuCLEAN 2.0 Manuel utilisateur

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuel utilisateur

Z-Wave

Z-Wave HSD-200Z Manuel utilisateur

turck

turck FMX-IM-2UPLI63FX Manuel utilisateur

Decagon Devices

Decagon Devices 10HS Manuel utilisateur

UPPAbaby

UPPAbaby Cup Holder Manuel utilisateur

Elko

Elko SmartSensor Leakage Wireless Manuel utilisateur

Grizzly

Grizzly H8371 Manuel utilisateur

Panasonic

Panasonic HG-T Series Manuel utilisateur

IFM Electronic

IFM Electronic Efector 250 Series Guide de référence

DigiDesign

DigiDesign 888/24 I/O Manuel utilisateur

PROZIS

PROZIS QUAY Manuel utilisateur

patagonia

patagonia PSI Vest Manuel utilisateur

SFC Energy

SFC Energy EFOY GO! Manuel utilisateur