Pentek 7341 Manuel utilisateur

Pentek Model 7341 Installation Manual Page 1

Manual Part No: 800.73410 Rev: B − November 20, 2009

Pentek, In .

One Park Way

Upper Saddle River, NJ 07458

(201) 818−5900

http://www.pentek.com

INSTALLATION MANUAL

MODEL 7341

Dual−Channel Multiband Transceiver

3U cPCI Board

Page 2 Pentek Model 7341 Installation Manual

Warranty

Pentek warrants that all produ ts manufa tured by Pentek onform to published Pentek spe ifi ations and are free from defe ts in materi−

als and workmanship for a period of one year from the date of delivery when used under normal operating onditions and within the ser−

vi e onditions for whi h they were furnished. The obligation of Pentek arising from a warranty laim shall be limited to repairing or at its

option, repla ing without harge, any produ t that in Pentek’s sole opinion proves to be defe tive within the s ope of the warranty. Pentek

must be notified in writing of the defe t or non onformity within the warranty period and the affe ted produ t returned to Pentek within

thirty days after dis overy of su h defe t or non onformity. Buyer shall prepay shipping harges, taxes, duties and insuran e for produ ts

returned to Pentek for warranty servi e. Pentek shall pay for the return of produ ts to buyer ex ept for produ ts returned from another

ountry.

Pentek shall have no responsibility for any defe t or damage aused by improper installation, unauthorized modifi ation, misuse, negle t,

inadequate maintenan e, or a ident, or for any produ t that has been repaired or altered by anyone other than Pentek or its authorized

representatives.

The warranty des ribed above is buyer’s sole and ex lusive remedy and no other warranty, whether written or oral, is expressed or

implied. Pentek spe ifi ally dis laims fitness for a parti ular purpose. Under no ir umstan es shall Pentek be liable for any dire t, indi−

re t, spe ial, in idental, or onsequential damages, expenses, losses or delays (in luding loss of profits) based on ontra t, tort, or any

other legal theory.

Copyrights

reprodu ed in any form without written permission.

Trademarks

Pentek, GateFlow, and ReadyFlow are registered trademarks or trademarks of Pentek, In .

Compa t PCI is a registered trademark of PICMG−PCI Industrial Computer Manufa turer's Group, In . DuPont is a trademark of E.I. du

Pont de Nemours and Company. Linux is a registered trademark of Linus B. Torvaids. PowerPC is a registered trademark of International

Business Ma hines Corporation. Mi rosoft and Windows are registered trademarks of Mi rosoft Corporation. VxWorks is a registered

trademark of Wind River Systems, In . Te hnobox is a trademark of Te hnobox, In . Xilinx, MultiLINX, and Virtex−II Pro are registered

trademarks or trademarks of Xilinx, In .

Manual Revision History

Date Revision Comments

11/19/07 Preliminary Initial release.

1/17/08 Se t 2.3, orre ted Pentek part # for JTAG PCB to 004.71402. Table 7−10, orre ted DAC data format.

1/24/08 Se t. 1.16, hanged transformer−related spe s for new analog input/output transformers.

4/17/08 Se t 2.2.1, added Jumper Blo k des riptions and default settings. Se t 4.10, added Note that JB1 pins

1−2 must be shorted to write−enable FLASH memory.

11/13/08 A Manual released, Revision A. Se t 2.3, added Xilinx JTAG J4 onne tor for Pentek JTAG PC Rev B.

11/20/09 B Changed to Installation Manual, see 800.7141 for Operating & Programming instru tions.

Added Option 703 CCA installation instru tions.

Printed in the United States of Ameri a.

Pentek Model 7341 Installation Manual Page 3

Page

Table of Contents

Rev.: B

Chapter 1: Introduction

1.1 General Des ription..............................................................................................................................5

1.2 Features ..................................................................................................................................................5

1.3 Model 7341 Do umentation ................................................................................................................5

1.4 Blo k Diagram.......................................................................................................................................6

igure 1−1: Model 7341 Block Diagram...........................................................................................6

1.5 Prin iple of Operation..........................................................................................................................7

1.6 Spe ifi ations.........................................................................................................................................8

Chapter 2: Installation and Connections

2.1 Inspe tion...............................................................................................................................................9

igure 2−1: Model 7341 Assembly....................................................................................................9

2.2 Jumper Settings...................................................................................................................................10

igure 2−2: PMC to cPCI Carrier, PMC Connection Side..........................................................11

2.2.1 Removing PMC Module from PCI Carrier .................................................................12

igure 2−3: Removing PMC Module from cPCI Carrier...........................................12

2.2.2 Removing PMC Module from PCI Carrier − Condu tion Cooled ..........................13

igure 2−4: Model 7141−703 PMC Mounting..............................................................13

2.2.3 Repla ing PMC Module onto PCI Carrier ...................................................................14

igure 2−5: cPCI Carrier PMC Connections ................................................................14

2.2.4 Repla ing PMC Module onto PCI Carrier − Condu tion Cooled ...........................15

igure 2−6: cPCI Carrier PMC Connections ................................................................15

2.3 7141 PMC Module Jumpers ..............................................................................................................16

igure 2−7: 7141 PMC Module, Component Side .......................................................................16

Table 2−1: Jumper Blocks JB1 & JB2..............................................................................................16

2.4 Installing the Model 7341 in a PCI Card Cage..............................................................................17

2.5 FPGA I/O Conne tions (Option 104) ..............................................................................................18

Table 2−2: Option 104 PGA I/O Pin Connections.....................................................................19

2.6 Front Panel Conne tions....................................................................................................................20

igure 2−8: 7141 PMC ront Panel.................................................................................................20

2.6.1 Analog Input Conne tors ................................................................................................20

2.6.2 Analog Output Conne tors .............................................................................................20

2.6.3 Clo k Input Conne tors ...................................................................................................20

2.6.4 SYNC/GATE Conne tor .................................................................................................21

Table 2−3: SYNC/GATE Connector Pins .....................................................................21

2.7 Front Panel LEDs................................................................................................................................22

2.7.1 Overload LEDs ..................................................................................................................22

2.7.2 Clo k LEDs ........................................................................................................................22

2.7.3 Master LEDs ......................................................................................................................22

2.7.4 Terminate LEDs ................................................................................................................22

2.7.5 Over Temperature LED ...................................................................................................22

Page 4 Pentek Model 7341 Installation Manual

Page

Table of Contents

Rev.: B

Chapter 2: Installation and Connections ( ontinued)

2.8 Signal Conne tions − Option 703..................................................................................................... 23

igure 2−9: Model 7141−703 PCB View, Component Side........................................................ 23

igure 2−10: Model 7341−703 ront Panel ................................................................................... 24

Pentek Model 7341 Installation Manual Page 5

Rev.: B

Chapter 1: Introduction

1.1 General Description

The Pentek Model 7341 is a omplete software radio trans eiver suitable for onne tion

to HF or IF ports of a ommuni ations system. Using the 3U Compa t PCI® ( PCI)

board format, it in ludes two A/D and two D/A onverters apable of bandwidths

greater than 40 MHz.

The Model 7341 onsists of one digital trans eiver PMC (PCI Mezzanine Card) module

mounted on a PMC to PCI 3U arrier board, assembled and tested as a single PCI

board. It it ready to plug into a 3U PCI hassis.

1.2 eatures

Two 80−MHz or 105−MHz, 14−bit A/D onverters

Four digital down onverters

One digital up onverter with two 500−MSPS, 16−bit D/A onverters

512 MBytes of DDR SDRAM

Xilinx® Virtex−II Pro™ Series FPGA

Up to 2.56 se onds of delay or data apture at 100 MHz

Dual timing buses for independent input and output lo k rates

LVDS timing bus an syn hronize multiple modules

32 pairs of LVDS onne tions to the Virtex−II Pro FPGA for ustom I/O

Optional ondu tion− ooled versions available

1.3 Model 7341 Documentation

This Model 7341 Installation Manual des ribes the installation and onne tions for the

7341 PCI assembly. Do umentation of the 7141 PMC operation and programming is

provided in the supplied Model 7141 Operating Manual, Pentek do ument #800.71410.

Datasheets for the programmable devi es on the Model 7341 are provided in the Pentek

Model 7x41 Series Supplemental Manual, part number 809.71410. This do ument is

available on the CD provided by Pentek, in file 80971410.pdf (PDF format).

Page 6 Pentek Model 7341 Installation Manual

Rev.: B

1.4 Block Diagram

The following is a simplified blo k diagram of the Model 7341.

GC4016

ANNEL

DIGITAL

RECEIVER

4−CH

CH 1

RF In

EXT

CLK A In

CH 2

RF In

LTC2255 #1

14−BIT A/D

LTC2255 #2

14−BIT A/D

TRANSFORMER

14 14

TIMING BUS

GENERATOR A

TTL G te/

Trigger

XTL

OSC.

SYNC,

INTERRUPTS

& CONTROL

TRANSFORMER

Control/

St tus

A/D 1

To All

Sections

PCI BUS 64 Bits/ 66 MHz)

PCI7140

PCI Interface

FPGA I/O

(Option 104)

Virtex−II Pro FPGA

Sync Bus B

TIMING BUS

GENERATOR B

XTL

OSC.

LVDS Clock A

LVDS Sync A

LVDS G te A

LVDS Clock B

LVDS Sync B

LVDS G te B

TTL Sync

Sync Bus A

CH 1

RF Out

TRANSFORMER

CH 2

RF Out

DAC5686

16−BIT D/A & DUC

EXT

CLK B In

DDR

SDRAM

32M x 32

DDR

SDRAM

64M x 32

DDR

SDRAM

32M x 32

A/D 2 DACBDACA

DDCA

DDCD

FLASH

8M x 16

32 32

cPCI J2

7141 PMC Module

cPCI Carrier Board

cPCI J1

Figure 1−1: Model 7341 Block Diagram

Pentek Model 7341 Installation Manual Page 7

Rev.: B

1.5 Principle of Operation

The Model 7341 is a omplete software radio trans eiver suitable for dire t onne tion

to HF or IF ports of a ommuni ations system. Using the PCI board format, the 7341

in ludes two A/D and two D/A onverters.

The 7341 features a Xilinx® Virtex−II Pro™ XC2VP50 Field−Programmable Gate Array.

The FPGA an be pre− onfigured with one of a variety of optional IP ores to provide

signal translation, pro essing and time delay fun tions. In addition to pre− onfigured

fun tions, user− reated FPGA programming is supported by Pentek's GateFlow®

Designer's Kit, Model 4953 Option 140. FPGA I/O onne tions are provided through

the optional PMC P4 onne tor (Option 104).

The 7341 in ludes a large 512−MByte blo k of DDR SDRAM. This memory is on−

trolled by the FPGA and is organized as two 128−MByte banks, 32 Mbyte deep by 32

bits wide and one 256−MByte bank, 64 Mbytes deep and 32 bits wide. Separate banks

(separate address and data per bank) allow simultaneous a ess to all banks. This

memory an be used as buffer memory when transferring data between board resour e

or to off−board resour es.

Dual A/D onverters provide input to a FPGA, where the data an be formatted, pro−

essed or routed to board resour es in luding the GC4016 quad digital down onverter.

The board design provides a dual hannel feedba k path between the FPGA and the

digital down onverter, allowing signals that have been pro essed or time delayed

inside of the FPGA to be sent to the digital down onverter's input.

Dual D/A onverters in lude both interpolation filters and an up onverter stage apa−

ble of produ ing base band I & Q, quadrature modulation, and single−sideband

up onversion analog output.

The 7341 in ludes dual onboard rystal os illators for lo king, but an also a ept

external lo ks through a pair of front panel MMCX onne tors. The PMC is equipped

with a dual LVDS front panel lo k and syn bus that an syn hronize up to eight

modules with built−in master/termination fun tions. The bus format is ompatible

with other Pentek PMC and VIM modules and will work with the Model 9190 Clo k

and Syn Distribution Amplifier for syn hronizing up to 80 modules.

Page 8 Pentek Model 7341 Installation Manual

Rev.: B

1.6 Specifications

PMC Signal Processing

Refer to the Model 7141 Operating Manual, Pentek do ument #800.71410

PMC to cPCI Carrier (3U)

Device:

Standard: Dynami Engineering PCI2PMC

Option 703: A romag ACPC4610CC (Condu tion ooled)

PMC Slots: One PMC site

PCI Bus Interface:

Standard: 32 or 64 bit, 33 or 66 MHz

Option 104: 32 bit, 33 or 66 MHz

Power

cPCI Carrier

With no PMC: (TBD)

7141 PMC

Current Draw: 3.3V 5V +12V −12V

Option 050,100: 1.07A 2.58A 0.2A 0.2A

(105 MHz A/D and standard FPGA fun tions)

Option 050,100,430: 1.10A 3.37A 0.2A 0.2A

(105 MHz A/D and GateFlow Core installed − i.e., heavy FPGA usage)

(±12V only onne ted to voltage test ir uit)

Total Power:

Option 050,100: 16.91 W

Option 050,100,430: 20.96 W

(Note: FPGA power onsumption will vary based on usage)

Physical

Dimensions: 3U 4HP PCI ard

Depth: 160.0 mm (6.3 in.)

Height: 100 mm (3.94 in.)

Weight:

PCI Carrier

Standard: (TBD)

Option 703: 230 grams (8 oz)

7141 PMC 127.6 grams (4.5 oz)

Environmental

Commercial Applications, Level L0

Cooling Method (operational): For ed Air

Operating Temperature: 0° to 50°C

Storage Temperature: −20° to 90°C

Relative Humidity: 0 to 95% non− ondensing

Pentek Ruggedization Level L3 (Option −703)

Cooling Method (operational): Condu tion Cooled

Operating Temperature: −40° to 70°C

Storage Temperature: −50°C to 100°C

Relative Humidity: 5−95% Non−Condensing

Pentek Model 7341 Installation Manual Page 9

Rev.: B

Chapter 2: Installation and Connections

2.1 Inspection

After unpa king, inspe t the unit arefully for possible damage to onne tors or om−

ponents. If any damage is dis overed, onta t Pentek immediately at (201) 818−5900.

Please save the shipping ontainer and pa king material in ase reshipment is required.

The following figure illustrates the omplete Model 7341 assembly as shipped, with the

7141 PMC module mounted onto the PMC to PCI 3U arrier (standard arrier illus−

trated).

PMC to cPCI

Carrier

7141 PMC Module

PMC

Panel

cPCI

Front

Panel

Figure −1: Model 7341 Assembly

Page 10 Pentek Model 7341 Installation Manual

Rev.: B

2.2 Jumper Settings

The following subse tions over user operating parameters that are set by shorting

jumpers on the Model 7341.

As shipped from the fa tory, jumpers are installed in default positions on your board.

The default operating parameters they sele t may or may not meet your requirements.

Before installing your Model 7341, please review the following subse tions to deter−

mine whether you need to hange any of these settings.

The Model 7341 in ludes one Pentek 7141 PMC module mounted on a PMC to PCI 3U

arrier. Different PCI arriers are used depending on the Option ordered.

Standard − Dynami Engineering model PCI2PMC

Option 703 ( ondu tion− ooled) − A romag ACPC4610CC

These PCI arrier models are illustrated in Figure 2−2 on the next page.

As shipped, the 7141 PMC module is mounted onto the PMC to PCI arrier. Note that

the jumper blo ks on the PMC are lo ated on the omponent side of the PMC, and are

not a essible in this shipped onfiguration. If you need to a ess the jumpers on the

7141 PMC, you must first remove the PMC module from the PCI arrier, as des ribed

in Se tion 2.2.1 (or Se tion 2.2.2 for the Option 703 arrier).

The jumpers on the PMC to PCI arrier have been fa tory set by Pentek for the onfig−

uration shipped.

Note

The user should not change jumpers not identified in these figures—these are

reserved for factory test and setup purposes only.

Table des matières

Autres manuels Pentek Émetteur-récepteur

Pentek

Pentek 7642 Manuel utilisateur

Manuels Émetteur-récepteur populaires d'autres marques

Yaesu

Yaesu FT-7B Manuel utilisateur

Kenwood

Kenwood ProTalk TK-3201 Manuel utilisateur

Texas Instruments

Texas Instruments TLK10232 Manuel utilisateur

Mizuho

Mizuho MX-2 Guide produit

Kenwood

Kenwood TK-3180 Manuel d'utilisation et d'entretien

Blitz

Blitz MJ-398U Manuel utilisateur

Utilicom

Utilicom LongRanger 2050 Manuel utilisateur

Standart

Standart HX290UKA Manuel utilisateur

Altronix

Altronix Pace1PTM Manuel utilisateur

Kirisun

Kirisun PT2208 Manuel utilisateur

ELECRAFT

ELECRAFT KX2 Manuel utilisateur

Zodiac

Zodiac K3 Manuel utilisateur

Assa Abloy

Assa Abloy SecureComm HKC GSM-WIFI U Manuel utilisateur

Kenwood

Kenwood TK-2217 Manuel utilisateur

Siemens

Siemens PSO 4000 Manuel utilisateur

Kenwood

Kenwood TS-590SG Manuel utilisateur

Midland

Midland G8E-BT Manuel

ComNav

ComNav Mariner X2 Manuel utilisateur