Pentax 76670 Manuel utilisateur

PENTAX Service Co.,Ltd

Technical Service Dep.

04,06 KN

PRODUCT No. 76670

ENGLISH

76670 -1/12-

[TABLE OF CONTENTS]

1. PREPARATION …................................................................................................... 2

1-1 Prepare the SD card for confirmation of adjustment

1-2 Setting the computer and copy the adjustment file to SD card

1-3 Set up the VB run time

2. DISASSEMBY AND ASSENBLY............................................................................ 6

Outline of Disassembly and Assembly..................................................................

2-1 Caution 6

2-2 Chart for Assemble, Adjustment and Confirmation......................................... 6

3.DISASSEMBLY AND ASSEMBLY PROCEDURES.

4.ADJUSTMENTTHEPROGRAMSOFT (SLRfunction)

4-1 Setting the computer

4-2 Preparation

4-3 Adjustment display

4-4 Items for Adjustment and checking

4-5 Procedureforadjustment

4-6 Procedure for ending the program soft

5.ADJUSTMENT THE PROGRAM SOFT (Digital function)

5-1Procedureforadjustment

6.Firmware 12

7. INFORMATION OF JIGS, TOOLS AND TESTERS FOR *ISTDS....................... 12

76670 -2/12-

Summary

*istDL2 (76670) is basically same as *istDL (76570)

The information in this manual is only for istDL2. For other information, please refer to the service

manual for istDL.

The service equipments are common use with istDL except service program soft.

1-1. Preparation for adjustment

Adjustment program soft for 76670（＊ist DL2）--- （Supply with CD-R）

Computer

SD memory card x 2 --- The size of memory should be bigger than 8MB

SD card reader or Camera and USB cable （I-USB17）--- Connect to PC

Preparation for SD memory card

1. Two SD memory card for FW

The following SD card is common use with istDL/istDS

2. For SW test

3. For Test mode ON

4. For test mode OFF

5. For initial set

1-2.Setting the computer and copy the adjustment file to SD card

(1) Copy the [76670 SLR] folder from the Programmed software contained in the CD-ROM to [C: drive] as

shown in the picture below. (For SLR adjustment)

(2) Copy the [76670] folder from the Programmed software contained in the CD-ROM to [C: drive] as shown in

the picture below. (For Digital adjustment)

(3) Copy the file of [kb411b.bin] from [GM_FW] holder

(4) Copy the file of [kb392.bin] from [Product ID FW] --- FW for new T100

76670

76670 SLR

76670 -3/12-

1-3 .Set up the VB run time

If your computer is not installed “VisualBasic” software, set up the VB run time is required as follow.

[Procedure]

①Set the 76670 adjustment program soft into the computer

②Execute the setup.exe in the folder of [vb6run_csx.x.x]

Installer will be started

* The Execute file and uninstall setting file will be generated

76670 -4/12-

③Click OK

④* Do not click Directory, Click installation button

76670 -5/12-

⑤Set up will be started

⑥Click OK to end the installation

76670 -6/12-

2. DISASSEMBY AND ASSENBLY.

2-1. Caution:

◆About FW installation and adjustment after replaced T100

The following procedure will be required ( Same as ＊istDS2（76640）)

2-2. Chart for Assemble, Adjustment and Confirmation.

Procedure of Adjustment and confirmation is same as ＊ist DL（76570）

Refer to the ＊ist DL（76570）Service manual

3, Procedure for Disassemble/Assembly

Procedure of Disassemble/Assembly is same as ＊ist DL（76570）

①FW for new T100

②FW for service

Adjustment

76670 -7/12-

4. ADJUSTMENT THE PROGRAM SOFT (SLR function)

Caution: When replaced T100, the following procedure should be completed

Preparation：

Programmed software for 76670 (for SLR operation), USB cable (I-USB17)

Computer (Windows 2000 / XP), AC-adaptor (D-AC10), Light source (Shutter tester)

Temporary bottom cover (Hand made/exclusive item), Power supply (8V,3A)

Shutter tester (1/4000 can be measured), Diaphragm set ring F8 (KA-0-1A), FA (F) 35-80mm F4-5.6,

AF positioning jig (Square) for 27830, AF positioning jig (Cross) for 27250, Power adaptor,

AF chart for 2m x2 (Exclusive item), AF master lens for 2m, FA Macro 50mmF2.8,

Driver1.5mm (HD-M1.5)、

4-1. SETTING THE COMPUTER

zSetting the computer (Page2) and Set up the VB run time (Page3)

should be completed

4-2. Preparation

When replaced T100 or CCD, the CCD ID number will be used

for digital adjustment

①Install battery cover for battery adaptor and temporally bottom cover

to the camera

②Set focus mode lever to [MF]

4-3. DISPLAY FOR ADJUSTMENT

When start the adjustment software, the following display will be opened

A. Tool Bar

C. Menu display

Adjustment items

Product number

Menu Bar B. USB connecting display

76670

76670 -8/12-

TOOL Bar

Display the status of USB connecting

USB Connecting is ON：Connect

USB Connecting is OFF：Unconnect

4-4. MENU Display

When click the items, the detailed will be displayed as follows

Detailed of adjustment items

1：[Eeprom checking] --- Check the data

2：[Exposure adjust] --- Adjustment of exposure

[BV adjust] (brightness value) --- Adjustment of measurement sensor

3：[AF and related adjust] --- Adjustment of AF

[CCD position adjust] --- Adjustment of CCD position

[AGC level adjust] --- Adjustment of AGC level

[Uniformity adjust] --- Adjustment of uniformity

[Focus offset adjust] --- Adjustment of AF focus

Start the correspond with Camera

Close the correspond with Camera

p.s Print screen

ver Display FW version

end End of adjustment

m.n Display Menu screen

Connect

76670 -9/12-

4：[Number of repairs] --- Record the number of repair

5：[Eeprom checking] --- Check the data

6：[Battery level adjust] --- Adjustment of Battery level

7：[Shutter speed adjust] --- Adjustment of High shutter speed

4-5. Adjustment procedure

①Turn the power of the camera Off and then install AC adaptor

* Suggest installing battery to avoid the Power supply interception

②Connect the camera to the computer via USB cable

③Turn the power of the camera ON and confirm that the camera is recognized by computer

④Click [PDCAdj01.exe] in the EXE folder

⑤Adjustment screen will be displayed

⑥Click [Op] to start correspond

*Confirmation: [Connect] should display as follow

⑦Execute the check/adjustment following the display screen as follows

1：EEPROM CHECKING

↓

2：EXPOSURE ADJUST

[BV ADJUST]

↓Tools：Focus master lens for 35mm (KML-01), Diaphragm set ring F8 (KA-0-1A)

↓Light source (LV6,LV8,LV12,LV15) or (LV6,LV9,LV12,LV16)

↓

3：AF AND RELATED ADJUST

↓Tools: AF positioning jig (Square) for 27830, AF positioning jig (Cross) for 27250, Light source LV12

↓Driver1.5mm (HD-M1.5), AF master lens for 2m, FA (F) 35-80mm F4-5.6,

↓AF chart for 2m x2 (Exclusive item), FA Macro 50mmF2.8,

↓

Connect

76670

Initialize the data

(Yes/No)

Yes

Replaced Main PCB？

T100ExChange

Did you exchange the

main pc board?

PDC Adj

Writing of initial EPROM.

6：BATTERY LEVEL ADJUST

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Pentax Appareil photo numérique

Pentax

Pentax IQZoom 28-W Manuel utilisateur

Pentax

Pentax E30 - Optio Digital Camera Manuel d'instructions

Pentax

Pentax PC35AF Manuel utilisateur

Pentax

Pentax SMART ZX-7 Manuel utilisateur

Pentax

Pentax Optio WG2 GPS Manuel utilisateur

Pentax

Pentax Optio W60 Mode d’emploi

Pentax

Pentax WG-90 Mode d’emploi

Pentax

Pentax ZX-5N - SLR Camera - 35mm Manuel utilisateur

Pentax

Pentax WG-10 Manuel utilisateur

Pentax

Pentax Espio Manuel utilisateur

Pentax

Pentax PC-33 DATE Manuel utilisateur

Pentax

Pentax EI-200 Manuel utilisateur

Pentax

Pentax K10D - Digital Camera SLR Manuel utilisateur

Pentax

Pentax 18263 - OptioS Digital Camera Manuel utilisateur

Pentax

Pentax 17731 Manuel utilisateur

Pentax

Pentax efina Manuel utilisateur

Pentax

Pentax K-7 Guide de démarrage rapide

Pentax

Pentax K-7 Manuel utilisateur

Pentax

Pentax K20D - Digital Camera SLR Manuel utilisateur

Pentax

Pentax K-5 II S Manuel utilisateur

Pentax

Pentax Q7 Manuel utilisateur

Pentax

Pentax IQZoom 700 Manuel utilisateur

Pentax

Pentax Pino 35M Manuel utilisateur

Pentax

Pentax Optio S50 Manuel utilisateur

Manuels Appareil photo numérique populaires d'autres marques

Mercury

Mercury 350K Manuel utilisateur

Sanyo

Sanyo VPC-S1085 Manuel utilisateur

GE SMART A1255 Manuel utilisateur

Point Grey

Point Grey Gazelle Manuel utilisateur

Nikon

Nikon COOLPIX A Manuel utilisateur

BlazeVideo

BlazeVideo A280 Manuel utilisateur

Sony

Sony MCA-20 Manuel utilisateur

Sony

Sony Alpha DSLR-A290 Manuel utilisateur

ATIK Cameras

ATIK Cameras One Manuel utilisateur

CohuHD Costar

CohuHD Costar 3930 Series Manuel utilisateur

Leica

Leica M10-R Manuel utilisateur

FujiFilm

FujiFilm FinePix A700 Manuel utilisateur

Lorex

Lorex LNZ81P25 Series Manuel utilisateur

GE J1470S Manuel utilisateur

Sony

Sony A6700 Guide de l'utilisateur

Canon

Canon EOS ELAN7 Manuel utilisateur

Nikon

Nikon Coolpix 100 Manuel utilisateur

Samsung

Samsung SCC-C4253 Manuel utilisateur