Pelonis HO-0280 Manuel utilisateur

Digital Oil-Filled

Radiator Heater

HO-0280

version A - 09 - 2021

HO-0280

midea.com

USER MANUAL

Warning Notice: Before using

this product, please read this

manual carefully and keep it for

future reference. For additional

support, please call customer

service at 1-866-646-4332.

The design and specifications are

subject to change without prior

notice for product improvement.

Consult with your dealer or

the manufacturer for details.

Rated voltage: 120V

Rated power: 1500W

Frequency: 60Hz

When using electrical appliances, basic precautions should always be followed to reduce

the risk of fire, electric shock, and injury to persons, including the following:

1. Read all instructions before using this heater.

2. This heater is hot when in use. To avoid burns, do not let bare skin touch hot

surfaces. If provided, use handles when moving this heater. Keep combustible

materials, such as furniture, pillows, bedding, papers, clothes, and curtains at

least 3 feet (0.9m) from the front of the heater and keep them away from the

sides and rear.

3. Extreme caution is necessary when any heater is used by or near children or

invalids and whenever the heater is left operating and unattended.

4. Always unplug heater when not in use.

5. Do not operate any heater with a damaged cord or plug or after the heater

malfunctions, has been dropped or damaged in any manner. Discard heater or

return heater to authorized service facility for examination, electrical or

mechanical adjustment, or repair.

6. Do not use outdoors.

7. This heater is not intended for use in bathrooms, laundry areas and similar indoor

locations. Never locate heater where it may fall into bathtub or other water

container.

8. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or

similar coverings. Do not route cord under furniture or appliances. Arrange cord

away from traffic area and where it will not be tripped over.

9. To disconnect heater, first turn controls to off, then remove plug from outlet.

10. Do not insert or allow foreign objects to enter any ventilation or exhaust opening

as this may cause an electric shock or fire, or damage the heater.

11. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do

not use on soft surfaces, like a bed, where openings may become blocked.

12. A heater has hot and arcing or sparking parts inside. Do not use it in the areas

where gasoline, paint, or flammable liquids are used or stored.

13. Use this heater only as described in this manual. Any other use not

recommended by the manufacturer may cause fire, electric shock, or injury to

persons.

14. Always plug heaters directly into a wall outlet/receptacle. Never use

with an extension cord or relocatable power tap (outlet/power strip).

PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS

Risk of fire. Do not operate heater without wheel assemblies

attached. Operate heater in upright position only (wheels on bottom,

controls on top). Any other position could create a hazardous situation.

Ensure that the surface beneath the heater is clean and free of any

obstructions. It is not recommended that this heater be placed on

high-pile carpeting or any other surface that impedes the flow of air

underneath the heater.

ASSEMBLY INSTRUCTIONS

Unpack your heater and find the wheel-holding plate and butterfly nuts between

the fins assemblies .

1. Make sure the heater is unplugged and in the "OFF" position.

2. TURN THE HEATER UPSIDE DOWN.

3. Attach the wheel-holding plates onto the heater as Fig.1 shows . The plate is

fixed between the last two fins and the other one is fixed under metal control box,

Fix the castors to the vertical axis of both

the wheel holding plates.

4. Insert the butterfly nuts and tighten them

securely .

5. TURN THE HEATER UPRIGHT.

Your heater is now ready to use .

15. This heater draws 12.5 amps during operation. To prevent overloading a circuit,

do not plug the heater into a circuit that already has other appliances working.

16. It is normal for the plug to feel warm to the touch; however, a loose fit between

the AC outlet (receptacle) and plug may cause overheating and distortion of the

plug. Contact a qualified electrician to replace loose or worn outlet.

17. The output of this heater may vary and its temperature may become intense

enough to burn exposed skin. Use of this heater is not recommended for

persons with reduced sensitivity to heat or an inability to react to avoid burns.

18. Don't leave the heater on unattended.

19.

This heater includes an Overheat Protection System that

shuts the unit off if it overheats due to abnormal conditions.

If this occurs turn the heater “OFF”, unplug it, and inspect and remove

any objects on or adjacent to the heater. Allow it to cool for a few

minutes, plug it back in, and resume normal operation.

Fig.1

OPERATING INSTRUCTION

How to use

[Inspection before startup]

1. Check the power cord for any damage;

2. Prior to use, please confirm that the power socket has acceptable rated current,

and if not, please replace it.

[Operation instructions]

<on/off >: By power on, the buzzer will give a long sound of “beep”. Press the

on-off key to start up and enter the high-grade heating, and then press the

on-off key to shut down.

<Gear selection >: Gently press the gear selection key “MODE” under the working

state to select any one of high-grade, middle-grade, low-grade and energy-saving

work modes.

<Temperature setting >: Under the working state, press and hold the “∧” key or

“∨” key to set the temperature, with the temperature setting step of 1; long press

the “∧” key or “∨” key to set the temperature quickly. After temperature setting,

exit the temperature setting interface in case of no operation for 5 seconds. In the

event of first use or self-inspection for memory information clearing, the machine

will operate after start according to the factory settings, and the high temperature

setting default is 95°F.

<Power-on by alarm>: Press the timing key “ ” in standby mode to enter the start

setting interface. Press the “∧” key or “∨” key to set time for startup. Long press

“∧” key or “∨” key to quickly set time for startup. Upon the time set, the machine

will start and the buzzer will make a long sound.

<Power-off by alarm>: Press the timing key “ ” in startup mode to enter the

shutdown setting interface. Press the “∧” key or “∨” key to set time for shutdown.

Long press “∧” key or “∨” key to quickly set time for shutdown. Upon the time set,

the machine will shut down.

A: Timing range between 0 and 24 hours. Increase or decrease for 1 hour by

pressing the “∧” key or “∨” key each time. When the setting value is 0H, press the

“∨” key to change the setting time to 24H. When the setting value is 24H, press

the “∧” key to change the setting time to 0H. When the setting value is 0H, cancel

the timing; when the setting value is not 0H, start the timing. After the time is set,

press the “ ” key or “MODE” key, or in case of no operation for 5 seconds, exit

the timing MODE.

B: If the time is set, press the “ ” key to shut down and cancel the timing.

C: After timing, press the “ ” key to check the remaining time and reset the time

at any time.

During the timing period, the machine can be stopped or restarted under the

temperature control state, and the timing will be kept normally, and not affected by

such stop and restart. In case of closedown or power off during the timing period,

the timer will reset to zero.

<Child lock function>: Under no child lock state during startup and standby, press

and hold the “ ” key and the “MODE” key for 3 seconds at the same time to start

the child lock function. Under child lock state during startup and standby, press and

hold the “ ” key and the “MODE” key for 3 seconds to turn off the child lock

function.

: Temperature decrease / Time decrease

: ON/OFF button

: Temperature increase / Time increase

: Timer button

: Mode button

Note:

1. When the child lock is in effect during startup, all operations other than shutdown

invalid (except release of the child lock); the child lock is canceled after shutdown.

2. When the child lock is in effect during standby, all operations are invalid (except

release of the child lock).

<Memory function>: If the machine is restarted after normal shutdown, it will run at

the latest state before shutdown. If the machine is powered on again after power

off, it will also run at the latest state before power off.

Note: The memory function is not applicable to child lock after power off.

<Safety protection function>: If the indoor environment temperature Th exceeds

122°F during standby or startup time, please close all output, the buzzer will give

ten acute sounds, and the digital display will show “FF” and flash for 75 seconds

with the frequency of 1HZ. If the protection function works, the machine cannot

resume running or operation, though the environment temperature is less than

122°F. In this case, it is necessary to power off and then power on the machine for

operation.

<Shutdown>: When the machine is turned on, press the “ ” key on the control

panel to enter the standby state. Unplug the power cord, and then place the electric

heater well after the machine is cooled.

[Electric heater movement]

To move the electric heater, please turn it off, unplug the power cord, and then

push the heater body to make the following four universal casters to scroll.

Note: In the event of first use or re-inserting the power plug into socket, please

check the compatibility of the plug and socket.

Inspection method: Insert the power plug into socket and turn the machine on.

About half an hour later, shut the machine down and disconnect plug to check

whether the plug pin is hot. If the pin is hot (about more than 122°F), the socket

must be replaced to avoid socket overheating and even fire caused by poor

contact.

SAFTEY FEATURES

The heater is equipped with an over-heat device which cause the unit to stop

operating in the event that the internal temperature exceeds the normal operating

temperature.

If the heater shuts down,

1. Turn off and unplug the heater.

2. Wait for at least 10 minutes until the heater cools.

3. Plug the heater into the power outlet and then turn it on.

Note: This heater includes a safety tip-over protection feature which will shut the

heater off in case it is tipped over. If, at any time, the heater does tip over, please

put the heater back in the upright position (wheels on bottom, controls on top).

The heater will resume its normal operation.

1. Press down on the battery compartment cover

and slide it out.

2. Use 1 "CR2032" lithium battery (included)

3. Insert the batteries, making sure that the positive

terminals are facing the proper way.

4. Replace the cover.

BATTERIES INSTRUCTIONS (included)

1. Do not dispose of batteries in fire, batteries may

explode or leak.

2. Do not mix old and new batteries.

3. Do not mix alkaline, standard (carbon-zinc) or

rechargeable (nickel-cadmium) batteries.

4. Non-rechargeable batteries are not to be recharged.

5. Batteries are to be inserted with the correct polarity.

6. Exhausted batteries are to be removed from the product.

7. The batteries must be removed from the remote controller before it is scrapped

and that they are disposed of safely.

BATTERY WARNING

INSTRUCTIONS TO REMOTE CONTROLLER

Timer key

Mode key

ON/Standby key

Temperature/Time increase

Temperature/Time decrease

TROUBLESHOOTING

Problem Reason Solution

1. There is no power. Be sure it is plugged in and that the electrical outlet is working.

2. The set temperature is lower than

the current room temperature.

Set the desired temperature higher than the current temperature to

restart the heater.

3. The room temperature has reached

the temperature set at the thermostat.

1. This is normal. The heater will restart once room

temperature is lower than set temperature.

2. Adjust the thermostat setting if it's not set to your desired

temperature.

4. One of the safety protection devices

had been activated to prevent

overheating.

1. Place the heater in upright position.

2. Check for any obstructions. If you find an obstruction, turn the

heater off.

3. Unplug the heater and wait at least 10 minutes for it to cool down.

4. Carefully remove the obstruction. Plug the heater in and restart it

as described in the OPERATION section.

5. If you still notice the same problem, remove the plug from the

outlet and have the appliance checked by an authorized service

person.

The room is not hot enough.

1. The room is too large.

3. The set temperature is too low.

4. The power setting is too low.

4. Increase the temperature setting.

5. Select the higher power setting.

2. The window is open.

1. Turn on the main heat source of the room.

2. Use more portable heaters.

3. Close the window.

Your heater shuts off

unexpectedly or fails to operate.

Please do not attempt to open or repair the heater by yourself.

Doing so may void the warranty and could cause damage or personal

injury.

SPECIFICATIONS

This heater is designed for finite space heating or as a supplementary heating source.

It can not replace the main heat source during the winter.

Voltage Frequency Wattage Max. Current BTU Output

120 V AC 60 Hz 1500 W 12.5 A 5120

CARE AND CLEANING

1. Always remove the plug from the power socket and allow heater to cool. Wipe

heater with a soft, damp cloth. Do not use detergents and abrasives.

2. If the heater is not in use over a certain length of time, wind the cable around the

holder and store it in a dry place.

3. In case of malfunction, do not try to repair the heater by yourself. It may result in

fire hazard or electric shock.

In the event of a warranty claim or if service is required for this heater, please contact us at the

following:

Toll Free: 866 646 4332

Email us at: [email protected]

For questions or comments, please write to:

Midea America Corp

Customer Care Center

5 Sylvan Way, Suite 100

Parsippany, NJ 07054

For your records, staple your sales receipt to this manual and record the following:

________________________________

SERVICE & SUPPORT

DATE OF PURCHASE:

PLACE OF PURCHASE:

(STAPLE SALES RECEIPT HERE)

NOTE: PROOF OF PURCHASE IS REQUIRED FOR ALL

WARRANTY CLAIMS

PRINTED IN CHINA

•Please read all instructions before attempting to use this product.

PELONIS

PELONIS.PELONIS

warrants as limited herein to the original purchaser of retail that each new Pelonis

Product, shall be free of defects in material and workmanship for a period of one (1) year from

the date of original purchase. This one (1) year warranty is limited to the heating elements,

motor, and electric control circuit board.

In the event of malfunctions or failure of your Pelonis Product, simply deliver or send the heater,

postage prepaid along with PROOF OF PURCHASE , within the warranty period of one (1) year, to

reserves the right to inspect the claimed defective part or parts to determine

if the defect or malfunction complaint is covered by this warranty. shall, within sixty

(60) days after receipt of the product, at its option,repair and/or replace the defective part or parts

free of charge. This warranty shall only cover defects arising from normal usage.

assumes no responsibility whatsoever if Product should fail during the warranty period by

reason of:

•Misuse, negligence, physical damage or accidents.

•Lack of maintenance (see instructions for proper maintenance).

•Repair by any unauthorized party during the warranty period.

•Damage caused by connection to an improper input voltage (see specification label on

your heater).

makes no further warranties or representations, express or implied except those

contained herein. No representative or dealer is authorized to assume any other liability

regarding the Product. The duration of the implied warranty granted under State law, including

warranties of merchantability and fitness for particular purpose are limited in duration should

the duration of the express warranty grant it hereunder. shall in no event be liable for

direct, indirect, special or consequential damages.

Some states do not allow limitations on how long an implied warranty lasts, and/or the above

limitations or exclusion may not apply to you. This warranty gives you specific legal rights and

you may have other rights which vary from state to state.

ONE (1) YEAR LIMITED WARRANTY

PELONIS

Free 3 months

extension* of the

original limited warranty

period! Simply text a

picture of your proof of

purchase to:

1-844-224-1614

*The warranty extension is for the

three months immediately following

the completion of the product's

original warranty period.

Table des matières

Langues :

Autres manuels Pelonis Chauffage

Pelonis

Pelonis NT15-13L Manuel utilisateur

Pelonis

Pelonis PSH700R Manuel utilisateur

Pelonis

Pelonis HC-0113 Manuel utilisateur

Pelonis

Pelonis HC-0119A Manuel utilisateur

Pelonis

Pelonis HC-0113 Manuel utilisateur

Pelonis

Pelonis PSH750S Manuel utilisateur

Pelonis

Pelonis PSH700 Manuel utilisateur

Pelonis

Pelonis PSH23FT3DSBC Manuel utilisateur

Pelonis

Pelonis PSH750R Manuel utilisateur

Pelonis

Pelonis HB-215T Manuel utilisateur

Pelonis

Pelonis HO-201 Manuel utilisateur

Pelonis

Pelonis PFH15A2BGB Manuel utilisateur

Pelonis

Pelonis HC-0125D Manuel utilisateur

Pelonis

Pelonis NY1507-14A Manuel utilisateur

Pelonis

Pelonis HC-0119A Manuel utilisateur

Pelonis

Pelonis 1500W-II Manuel utilisateur

Pelonis

Pelonis HF-0021 Manuel utilisateur

Pelonis

Pelonis PSH08F1ABBC Manuel utilisateur

Pelonis

Pelonis NTK15A Manuel utilisateur

Pelonis

Pelonis HF-0063 Manuel utilisateur

Pelonis

Pelonis PSHF2022EOC Manuel utilisateur

Pelonis

Pelonis HO-0221 Manuel utilisateur

Pelonis

Pelonis NY1506-18SRA Manuel utilisateur

Pelonis

Pelonis NT20-12D Manuel utilisateur

Manuels Chauffage populaires d'autres marques

oventrop

oventrop Regucor Series Manuel utilisateur

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuel utilisateur

ELMEKO

ELMEKO ML 150 Manuel utilisateur

BN Thermic

BN Thermic 830T Manuel utilisateur

KING

KING K Series Mode d’emploi

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guide de démarrage rapide

Well Straler

Well Straler RC-16B Manuel utilisateur

EUROM

EUROM 333299 Manuel utilisateur

Heylo

Heylo K 170 Manuel utilisateur

Eterna

Eterna TR70W Manuel utilisateur

Clarke

Clarke GRH15 Mode d’emploi

IRSAP

IRSAP The Radiator Company Ovali Manuel utilisateur

Empire Heating Systems

Empire Heating Systems WCC65 Manuel utilisateur

Wetekom

Wetekom 92 86 43 Manuel utilisateur

Desa

Desa SPC170-F Manuel utilisateur

Watlow

Watlow Watrod Electric Tubular Heaters Manuel utilisateur

Haverland

Haverland ECO-DRY GPS Series Manuel de la liste des pièces

Stelpro

Stelpro ASILVC2060 Series Manuel utilisateur