Pelican Advantage Series Manuel utilisateur

Owner’s Manual

Advantage Series

Salt Based Water Softeners

Nitrate Series Salt Based Filter System

Tannins Series Salt Based Softeners

Pelican Water Systems

AdvantageSeriesSaltBasedWaterSofteners/NitrateSeriesSalt

Based Filter System / Tannins Series Salt Based Softeners

3060 Performance Circle, Suite 2, DeLand, FL 32724

— Rev G

Page 2

www.pelicanwater.com

(877) 842-1635

All information contained herein is the property of Pelican Water Systems. Pelican Water Systems makes

no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of

merchantability and fitness for a particular purpose. Pelican Water Systems shall not be liable for technical

or editorial errors or omissions contained herein or for incidental or consequential damages in connection

with the furnishing, performance, or use of this material. The information is provided “as is” without

warranty of any kind and is subject to change without notice. This document contains proprietary

information which is protected by copyright. No part of this document may be photocopied, reproduced, or

translated into another language without the prior written consent of Pelican Water Systems. Pelican Water

Systems is an Enviro Water Solutions, Inc. company.

Pelican Water Systems

AdvantageSeriesSaltBasedWaterSofteners/NitrateSeriesSalt

Based Filter System / Tannins Series Salt Based Softeners

3060 Performance Circle, Suite 2, DeLand, FL 32724

— Rev G

Page 3

www.pelicanwater.com

(877) 842-1635

Table of Contents

Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Product Operation and Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Complete Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Installation Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Pre-Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Bypass Valve Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Install Electronic Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Final Setup and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Complete the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Programming the Electronic Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Step 1: Setting the Valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Step 2: Setting the Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Step 3: Performing Manual Regen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Adding the Pelican Logo Sticker: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Warranty Registration Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Pelican Water Systems

AdvantageSeriesSaltBasedWaterSofteners/NitrateSeriesSalt

Based Filter System / Tannins Series Salt Based Softeners

3060 Performance Circle, Suite 2, DeLand, FL 32724

— Rev G

Page 4

www.pelicanwater.com

(877) 842-1635

Product Operation and Specifications

Important Information

Read these instructions carefully and determine the location of all system components before

beginning installation.

Check all applicable plumbing, building, and electrical codes for installation compliance.

Install the system on the main water supply.

Systems that contain electronic components cannot be installed outside in uncovered areas.

WARNING:

If this or any other system is installed in a metal (conductive) plumbing system, i.e. copper or

galvanized metal, the plastic components of the system will interrupt the continuity of the

plumbing system. As a result any errant electricity from improperly grounded appliances

downstream or potential galvanic activity in the plumbing system can no longer ground

through contiguous metal plumbing. Older homes may have been built in accordance with

building codes from decades ago, some of which actually encouraged the grounding of

electrical appliances through the plumbing system. Consequently, the installation of a bypass

consisting of the same material as the existing plumbing, or a grounded "jumper wire"

bridging the equipment and re-establishing the contiguous conductive nature of the

plumbing system must be installed prior to your systems use.

CAUTION:

When adding a filtration/softening system to homes/buildings supplied by well water, the system should be

installed following the pressure tank. DO NOT USE this system for pneumatic or hydro pneumatic

applications. If you are using a booster pump, then install this system following the booster

pump. If you have questions, please call customer service.

Specification Description

Rated Service Flow 7-18 GPM (depending on model)

Minimum Working Pressure 25 PSI

Maximum Working Pressure 100 PSI

Maximum Vacuum 5 inch/127 mm Hg

Operating Temperatures 36°F - 120°F

pH Range 6.5 - 11

Pelican Water Systems

AdvantageSeriesSaltBasedWaterSofteners/NitrateSeriesSalt

Based Filter System / Tannins Series Salt Based Softeners

3060 Performance Circle, Suite 2, DeLand, FL 32724

— Rev G

Page 5

www.pelicanwater.com

(877) 842-1635

Complete Parts List

Note: Pelican supplies the parts below to accommodate a variety of water supply lines.

Table 1: Parts List

Note: Drawings are not to scale.

Additional fittings will be needed to adapt to your plumbing.

Part Description Qty. Part Description Qty.

Bypass Valve for Electronic

Head 11" PVC Tail Adaptor for

Electronic Head Bypass 2

PVC Tubing Drain Line

(50 ft.) 1Electronic Head 1

Brine Tank 1Mineral Tank 1

Pelican Water Systems

AdvantageSeriesSaltBasedWaterSofteners/NitrateSeriesSalt

Based Filter System / Tannins Series Salt Based Softeners

3060 Performance Circle, Suite 2, DeLand, FL 32724

— Rev G

Page 6

www.pelicanwater.com

(877) 842-1635

Installation Overview

Figure 1

Pre-Installation

Bypass Valve Installation

Figure 2

If the Red Clips are in the slots (female opening of Electronic Head) remove them. Push the male O-Ring

side of the Bypass Valve into the female opening of the Electronic Head. Push the Red Clips back into the

slots to tighten.

Notice:

The Bypass Valve on the Electronic Head can be set to Bypass or Service by turning the knobs on the side

of the valve. If the holes are up and down then the tank is in the Bypass Mode. If the holes are side to side

then the tank is in the Service Mode. Do not remove the red clips from the Bypass Valve after connecting

to main water supply.

Mineral Tank

Electronic

Head

Discharge

Line

Outgoing

Water to

House

Wall

Incoming

Water

Supply

Brine Tank

Holding Tank

Safety Valve

Mineral Tank

Electronic

Head

Bypass

Valve

Red

Clip

Front View

Pelican Water Systems

AdvantageSeriesSaltBasedWaterSofteners/NitrateSeriesSalt

Based Filter System / Tannins Series Salt Based Softeners

3060 Performance Circle, Suite 2, DeLand, FL 32724

— Rev G

Page 7

www.pelicanwater.com

(877) 842-1635

Installation

Install Electronic Head

Figure 3

Notice:

Follow the raised black arrows on the head of the Mineral.

1. Level the Pelican Mineral Tank.

Notice:

If the tank is not level, lift the tank straight up 6 inches and tap it on the ground until the tank stands

vertical. The bottom of the tank is round and the boot allows the tank to stand upright.

2. Determine the size and material of your incoming water supply line from the In-Line Injection Port

and choose the appropriate fittings required to connect it to the Bypass Valve.

CAUTION:

Do not over-tighten any of the fittings during installation.

Table 2: Bypass Valve Fittings

Note: The fitting above is designed with a ¼" give to allow for proper pipe alignment. It will not leak and

is intended to have some flexibility.

3. Remove the gray cap from the top of the Mineral tank.

4. Screw the Electronic Head onto the tank hand-tight.

Part Description Qty.

1" PVC Tail Adaptor for

Electronic Head Bypass 2

Mineral Tank

Electronic

Head

Discharge

Line

Outgoing

Water to

House

Wall

Incoming

Water

Supply

Brine Tank

Holding Tank

Safety Valve

Pelican Water Systems

AdvantageSeriesSaltBasedWaterSofteners/NitrateSeriesSalt

Based Filter System / Tannins Series Salt Based Softeners

3060 Performance Circle, Suite 2, DeLand, FL 32724

— Rev G

Page 8

www.pelicanwater.com

(877) 842-1635

5. Install the fittings onto the inlet and outlet, following the arrows on the Bypass Valve and head.

6. Connect the incoming water supply to the fitting on the inlet side of the Bypass Valve.

7. Connect the outgoing water supply to the outlet side of the Bypass Valve.

8. Firmly press one end of the discharge PVC Tubing Drain Line onto the barbed nose, and secure the

other end of the line to a drain.

Pelican Water Systems

AdvantageSeriesSaltBasedWaterSofteners/NitrateSeriesSalt

Based Filter System / Tannins Series Salt Based Softeners

3060 Performance Circle, Suite 2, DeLand, FL 32724

— Rev G

Page 9

www.pelicanwater.com

(877) 842-1635

Final Setup and Installation

Figure 4

1. Attach the supplied Drain Line to the discharge line on the top of the Electronic Head and run the

other end of the line to an external drain.

2. Attach the Brine Tank hose to the connection on the top of the Electronic Head.

!IMPORTANT!

Ensure the PVC Tubing Drain Line is free of kinks.

Complete the Installation

1. Set the Bypass Valve into bypass mode.

2. Slowly turn on the main water supply until all pipes are pressurized.

3. Slowly open the bypass valves.

4. Let the Mineral Tank fill completely and then open the bypass valves the rest of the way.

5. Check for leaks.

6. Plug in the Electronic Head.

Programming the Electronic Head

Note: These settings are specific to this system. Do not make changes to the settings unless instructed by

customer service. All settings have to be set by first setting the clock to 12:01 PM. To restart programming,

you must start over at step 1. Do not go to a previous step, you must start over at step 1.

Mineral Tank

Electronic

Head

Discharge

Line

Outgoing

Water to

House

Wall

Incoming

Water

Supply

Brine Tank

Holding Tank

Safety Valve

Pelican Water Systems

AdvantageSeriesSaltBasedWaterSofteners/NitrateSeriesSalt

Based Filter System / Tannins Series Salt Based Softeners

3060 Performance Circle, Suite 2, DeLand, FL 32724

— Rev G

Page 10

www.pelicanwater.com

(877) 842-1635

Figure 5

Step 1: Setting the Valve

1. Press and hold the UP or DOWN button to change the clock to 12:01 PM.

2. Press the EXTRA CYCLE button once.

3. Press and hold the UP and DOWN buttons together, until DF is displayed in the left corner. Scroll

using the UP and DOWN arrows until "GAL" is selected. Press EXTRA CYCLE.

4. Follow the steps in the table below to finish setting the valve. When each setting is displayed, use

the UP and DOWN buttons to scroll to the appropriate data setting displayed in the table. Press

EXTRA CYCLE to select the data setting and go to the next setting.

Table 3: Setting the Valve

Step 2: Setting the Time

1. Press and hold down the UP button to change the clock.

2. Press the EXTRA CYCLE button when the time is set. The water valve displayed will stop flashing

when the time is set.

Note 1: For Pelican PN3/PN6 Nitrate Systems, set to 4 (days override) instead of 14 days.

Parameter Display (Left Corner) Data Display Set To

VT dF2b

CT FD

CSee Note 3

H20

RS SF

SF 10

DO 14 (See Note 1 for PN3/PN6 Nitrate Systems and

Note 2 for NPT3/PT6 Tannin Filters)

RT 2:00

B1 10

BD 60

B2 5

RR 10

BF 20

FM 1.2 - Unit will begin syncing

Extra Cycle

Button

Down

Button

Pelican Water Systems

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Pelican Système d'eau

Pelican

Pelican WF6 Manuel utilisateur

Pelican

Pelican Calcite Cartridge System Manuel utilisateur

Pelican

Pelican 1354 NaturSoft Manuel utilisateur

Pelican

Pelican Hot Water Post-Filter System Manuel utilisateur

Pelican

Pelican WF6 Manuel utilisateur

Pelican

Pelican Premium WHWF 1865 Manuel utilisateur

Manuels Système d'eau populaires d'autres marques

Spirotech

Spirotech SPIROVENT SUPERIOR S250 Manuel utilisateur

Culligan

Culligan Aqua-Cleer Aqua-Cleer Advanced Drinking Water... Manuel utilisateur

A.O. Smith

A.O. Smith Dura-Max AJH - 1000A - P Manuel utilisateur

Microline

Microline T.F.C.-4 Manuel

Eureka Forbes

Eureka Forbes Aquaguard Select Manuel utilisateur

Cetetherm

Cetetherm AquaEfficiency Manuel utilisateur

CB Tech

CB Tech CB-VOC Manuel utilisateur

Vaillant

Vaillant auroFLOW plus VPM 15 D Manuel utilisateur

resideo

resideo Braukmann HS10S Manuel utilisateur

Gude

Gude INOX 100/24 Manuel utilisateur

Mono

Mono Eco 1-60 Manuel

SpectraPure

SpectraPure Drinking Water Kit Manuel utilisateur

HydroCare

HydroCare Dual Action Manuel utilisateur

NEXT pool

NEXT pool STERILOR Cu/Ag Schéma de câblage

Alpha

Alpha SolarSmart 150 Guide de l'utilisateur

TA FRISTAR3 Manuel utilisateur

GÜDE

GÜDE HWA 800 K Manuel utilisateur

Rainfresh

Rainfresh UCS2 Manuel utilisateur