Peco PS5 Manuel utilisateur
OPERATOR’S MANUAL
MANUAL PART#: Q0582 Initial Release - Sept 2021
ASSEMBLY OPERATION MAINTENANCE
P
PP
PECO
PECOPECO
PECO
PECOPECO
P
PP
P
PP
P
P
PECO
PECO
RRR
PS5 Power Sprayer
THE ORIGINAL
POWER SPRAYER
Model# 12008
2
PECO POWER SPRAYER
TABLE OF CONTENTS
SECTION PAGE
Safety - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 2
Warranty - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 3
I INTRODUCTION AND DESCRIPTION - - - - - - - - - - - - 4
Introduction- - - - - - - - - - - - - - - - - - - - - - - - - - - - 4
Description - - - - - - - - - - - - - - - - - - - - - - - - - - - - 4
II INSTALLATION FOR USE - - - - - - - - - - - - - - - - - - - - - 5
Sprayer Pump Installation - - - - - - - - - - - - - - - - - - 5
Battery Installation - - - - - - - - - - - - - - - - - - - - - - - 5
Component Back Installation - - - - - - - - - - - - - - - - 6
Component Top Installation - - - - - - - - - - - - - - - - - 7
Right & Left Chassis Installation - - - - - - - - - - - - - - 7
Power Sprayer Handle Assy Installation - - - - - - - - - 8
Power Sprayer Handle Assy Adjustment - - - - - - - - 9
Power Sprayer Wheel Installation - - - - - - - - - - - - - 9
SECTION PAGE
29” Stainless Steel Sprayer Wand Installation - - - - - 10
Sprayer Wire Harness - - - - - - - - - - - - - - - - - - - - 11
Exploded Views & Parts List - - - - - - - - - - - - - - 12-14
Overall Parts List - - - - - - - - - - - - - - - - - - - - - - - - 15
Safety Decals - - - - - - - - - - - - - - - - - - - - - - - - - - 16
III OPERATING INSTRUCTIONS - - - - - - - - - - - - - - - - - - 17
General Safety - - - - - - - - - - - - - - - - - - - - - - - - - 17
Battery & Charging Information - - - - - - - - - - - - - - - 17
Sprayer Care - - - - - - - - - - - - - - - - - - - - - - - - - - 17
Storage - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 17
V PARTS AND SERVICE - - - - - - - - - - - - - - - - - - - - - - - 17
Parts And Service Information - - - - - - - - - - - - - - - 17
Viton’s Chemical Compatibility - - - - - - - - - - - - - 18-20
Additional Option - - - - - - - - - - - - - - - - - - - - - - - - 21
SAFETY
2021 (v1.0)
1. Read the operator’s manual carefully and familiarize yourself with the proper use of your sprayer
2. Know the controls and how to use them properly. READ THE OPERATOR’S MANUAL!
3. Always inspect your sprayer thoroughly before and after each use. Check to be sure hose is securely attached and
in good condition before use.
4. Use special care when spraying near electrical installations.
5. Keep the work area clear of people and animals.
6. Never use the sprayer during windy conditions.
7. Wear protective gear and clothing when filling, using and cleaning the sprayer.
8. Always release pressure in the pump prior to filling, cleaning or servicing the sprayer.
9. Before opening a container of the spray material carefully read, understand and follow all instructions provided by
the spray material's manufacturer
10. Do not eat, drink or smoke while spraying.
11. Thoroughly wash face and hands with soap and water after spraying.
12. Do not transfer spray materials to other containers, especially food and/or drink containers.
13. Keep spray materials locked up and out of reach of children and animals.
14. Use only original manufacture's replacement parts.
3
New PECO, Inc. extends the following warranties to the ORIGINAL PURCHASER of each New PECO, Inc. consumer product
purchased from one of our Dealers or directly from New PECO, Inc., subject to the following limitations:
A. ITEMS COVERED UNDER WARRANTY:
1. PRODUCT WARRANTY –
Any part or parts which are deemed defective in material or workmanship, as delivered to the
original purchaser, will either be repaired or replaced, as New PECO, Inc. elects, without charge for parts or labor, if
the defect appears within 12 months from the date of purchase of the product to the Original Purchaser.
2. PARTS REPLACED DURING WARRANTY –
Any New PECO, Inc. part which is furnished in performance of this warranty
and is defective in material or workmanship as delivered to the purchaser will be repaired or replaced, as New PECO,
Inc. elects, before the expiration of the original warranty period.
B. WARRANTY DISTINCTIONS:
1. RESIDENTIAL -
Products put to a personal use around a single household or residence are considered Residential.
Products designated as “Residential” are warrantied for 12 months from the date of purchase of the product, to the
ORIGINAL PURCHASER with proof of purchase, when used for or in residential applications.
2. COMMERCIAL –
Products put to any business use (agricultural, commercial or industrial) or used at multiple locations
are considered Commercial. Products designated as “Commercial” are warrantied for 12 months from the date of
purchase of the product, to the ORIGINAL PURCHASER with proof of purchase, when used for or in commercial
applications. Products designated as “Residential” are warrantied for 90 days from the date of purchase of the
product, to the ORIGINAL PURCHASER with proof of purchase, when used for or in Commercial applications.
3. RENTAL –
Products used for Rental or Lease Purposes are warrantied for 45 days from date of purchase of the product,
to the ORIGINAL PURCHASER with proof of purchase, when used for or in a rental business.
C. ITEMS NOT COVERED BY NEW PECO WARRANTY:
1. ENGINES & BATTERIES: Engines and Batteries attached to New PECO, Inc. products are covered under their respective
separate manufacturer warranties and those companies must be contacted directly to file a warranty claim. Briggs &
Stratton: https://www.briggsandstratton.com/na/en_us/support/warranty.html
2. UNAPPROVED ALTERATION OR MODIFICATION: All obligations of New PECO, Inc. under this warranty shall be
terminated if products are altered or modified in any way not approved by New PECO, Inc.
3. ACCIDENTS & NORMAL MAINTENANCE: This warranty covers ONLY manufacturers defective material and
workmanship. It does not cover depreciation or damage caused by normal wear & tear, accident, improper
maintenance, misuse or abuse of products. New PECO, Inc. products must be operated and maintained in
accordance with the instructions furnished in the manuals. The cost of normal maintenance and normal replacement
of service items such as belts, cutting blades, hoses, bags, etc., which are not defective shall be paid for by the
purchaser.
4. NO SERVICE CENTER WARRANTY: The selling Service Center/Dealer makes no warranty on his own on any item
warranted by New PECO, Inc. unless he delivers to purchaser a separate written warranty certificate specifically
warranting the item. The Service Center or Dealer has no authority to make any representation or promise on behalf
of New PECO, Inc. or to modify the terms of the original warranty in any way.
5. NO REPRESENTATIONS ADDITONAL WARRANTIES, DISCLAIMER: Neither New PECO, Inc. nor any company affiliated
with New PECO, Inc. makes any warranties, representations or promises as to the quality of performance of its
products other than those set forth herein. Except as described above, New PECO, Inc. makes no other warranties
AND SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES OF FITNESS AND MERCHANTABILITY.
6. REMEDIED EXCLUSIVE: The only remedies the purchaser has in connection with the breach or performance of any
warranty on New PECO, Inc. consumer products are set forth above. In no event will New PECO, Inc. be liable for
special incidental or consequential damages.
Warranty service is available through your local authorized service dealer or distributor. If you do not know the dealer or
distributor in your area, search by your zip code on www.lawnvac.com
or contact our Sales Department at New PECO, Inc.
800-438-5823 or email [email protected]m.
PECO LIMITED WARRANTY FOR NEW PRODUCTS
2020 (v1.0)
4
Introduction
Thank you for purchasing the PECO Power Sprayer.
Your new PECO Sprayer has been engineered and
manufactured to PECO’s high standards for safety,
quality, dependability and ease of operation.
No need for pumping or lugging with the all new PS5
Power Sprayer. It’s completely self-contained and rolls
easily over lawns and through gardens. The spray wand
is always right at hand with multiple spray patterns to fit
the job. Spray from flat or a fine mist adjustable to a 40’
stream. A full charge on the battery can last for 6 hours,
and the wide-mouthed illuminated container can hold up
to five gallons. The sprayer handle folds for easy
transport & storage.
Description
Self-contained 12-volt Electric Sprayer
14” Wheels and Lightweight Aluminum Cart with Folding
Handle for easy Transport & Storage
40psi Electric Pump runs up to 6 hours on a single
charge
Viton Valves / Santoprene Diaphragm
Illuminated Wide-Mouth 5-Gallon Container
Standard Adjustable Nozzle Spray adjusts from a fine
mist to a 40 foot Solid Stream
TeeJet Nozzle for Uniform Coverage throughout the Flat
Spray pattern also included
29” Stainless Steel Spray Wand
Commercial Shut-Off Valve with Lock On / Off Features
10’ Hose with a Quick-Release Hose Hanger
SECTION 1 - INTRODUCTION & DESCRIPTION
5
Sprayer Pump Installation
Align and position the Sprayer Pump (Item #2) to the (4) mount holes on the Chassis Body (Item #1) as shown in
Figure A. Secure the Sprayer Pump by using (4) #10-12 Flat Tinnerman Nuts (Item #3) and (4) #10-12 x 3/4” Blunt Tip
Sheet Metal Screws (Item #4). Refer to Figure A.
Note: Some parts and part features have been hidden from view for visual clarity.
Figure A
Battery Installation
Position the Power Sprayer Battery (Item #1) vertically, as shown in Figure A, to the right side of the Sprayer’s
Chassis Body (Item #2). Secure the Power Sprayer Battery by using (1) Battery Clamp (Item #3), (1) 1/4”-20 x 4-1/2”
Carriage Bolt (Item #4), (1) Heavy Washer (Item #5) and (1) 1/4-20” Wing Nut (Item #6). Refer to figure B.
Note: Some parts and part features have been hidden from view for visual clarity.
Figure B
Section II - INSTALLATION FOR USE
6
Component Back Installation
Once your Sprayer Pump & Power Sprayer Battery has been installed, install the aluminum Component Back (Item
#2) to the Chassis Body (Item #1).
First, locate all bolt holes on the edge of both parts and install (12) Small Tinnerman Clips (Item #4). See Figure A.
Next, align the Component Back to the Chassis Body by aligning the (2) bottom bolt holes to those on the Chassis
Body and securing the Component Back by using (2) #10-12 x 1/2” Tinnerman Screws (Item #5). See Figure A.
Finally, install (3) Grommets into the 1-1/8” Dia Holes located on the Front and Left side of the Chassis Body. See
Figure B.
Note: Some parts and part features have been hidden from view for visual clarity.
Figure A
Figure B
7
Component Top Installation
With the pre-installed Tinnerman Clip (Item #4) onto the Chassis Body (Item #1) and the Component Back (Item #2),
install the Aluminum Component Top (Item #3) by aligning the Top over the Chassis Body and the Component Back
by securing the Top by using (4) #10-12 x 1/2” Tinnerman Screws (Item #5). Refer to the Figure below.
Note: Some parts and part features have been hidden from view for visual clarity.
Right & Left Chassis Installation
To install the Right Chassis (Item #1), first install (5) Small Tinnerman Clips (Item #4) to the Right side of the Chassis
Body. Then Align the Right Chassis’ bolt holes with the Tinnerman Clips and secure the Right Chassis by using (7)
#10-12 x 1/2” Tinnerman Screws (Item #3). See Figure B.
To install the Left Chassis (Item #2), first install (5) Small Tinnerman Clips (Item #4) to the Left side of the Chassis
Body. Then Align the Left Chassis’ bolt holes with the Tinnerman Clips and secure the Left Chassis by using (9) #10-
12 x 1/2” Tinnerman Screws (Item #3). See Figure C.
Note: Some parts and part features have been hidden from view for visual clarity.
Figure B
Figure C
Figure A
Installed Component Top
8
Power Sprayer Handle Assembly Installation
Before installing the Power Sprayer Handle Assembly (Item #1), install (2) Locator Pin Nuts (Item #3) to either side of
the Chassis by using (2) 1/4”-20 x 1/2” HHCS (Item #4). See Figure A.
Once the Locator Pin Nuts have been installed, position the Chassis Brace (Item #2) between the Left & Right
Chassis as seen in Figure B. Align the Chassis Brace’s bolt holes to those on the Left & Right Chassis keeping it
positioned in place by using (2) 5/16”-18 x 1-1/4” Carraige Bolts (Item #6).
When the Chassis Brace is in place, place (2) 5/16” Flat Washers (Item #5) over the Carriage Bolt on the outside of
the Chassis. Then Position the Power Sprayer Handle Assembly (Item #1) over Flat Washer and Carriage Bolt.
Secure the Power Sprayer Handle Assembly by using (2) Wing Knobs (Item #7). Refer to Figure B below.
Note: Some parts and part features have been hidden from view for visual clarity.
Figure A Figure B
9
Power Sprayer Handle Assembly Adjustment
The Power Sprayer Handle Assembly P#(A2377) position can be adjusted to lower or raise the Handle by moving the
(2) Locator Pin Nuts P#(B4251) to the different set of holes. See Figure A below.
Note: Some parts and part features have been hidden from view for visual clarity.
Figure B
Sprayer Wheel Installation
Before installing the Sprayer Wheels (Item #1), install the Axle (Item #2) by passing it through the through hole of
both the Left & Right Chassis. Refer to Figure A.
Next, place a Spacer Bushing (Item #3) on either side of the Axle outside of the Left & Right Chassis.
Once, the Spacer Bushing is in place, slide the Sprayer Wheel over the Axle and secure the Sprayer Wheel by using
(1) 5/8” Push Nuts (Item #4) PER side. Refer to Figure A below.
Note: Some parts and part features have been hidden from view for visual clarity.
Figure A
Handle Assembly
to Locator Pin
Locator Pin
Adjustment Holes
10
J1204B Flat Nozzle (Standard) J1205 Elbow Nozzle (Secondary)
29” Stainless Steel Sprayer Wand Assembly
Your Stainless Steel Sprayer Wand Assembly will come installed with a standard Flat Nozzle (Item #2), there will be a
secondary Elbow Nozzle P#(J1205) available as shown in Figure B.
When switching out your Sprayer Nozzle, you can store whichever one you’re not using onto the Chassis Brace as
shown in Figure C.
Sprayer Nozzle Types
Figure A
Figure B
Figure C
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Peco Pistolet à peinture
