PCB Piezotronics 482C24 Manuel utilisateur

Model 482C24

SENSOR SIGNAL CONDITIONER

Installation and Operating Manual

For assistance with the operation of this product,

contact the PCB Piezotronics, Inc.

Toll-free: 716-684-0001

24-hour SensorLine: 716-684-0001

Fax: 716-684-0987

E-mail: [email protected]

Web: www.pcb.com

Manual 21354 Rev E

ECN 50523

Repair and Maintenance

PCB guarantees Total Customer Satisfaction through its

“Lifetime Warranty Plus” on all Platinum Stock Products

sold by PCB and through its limited warranties on all other

PCB Stock, Standard and Special products. Due to the

sophisticated nature of our sensors and associated

instrumentation, field servicing and repair is not

recommended and, if attempted, will void the factory

warranty.

Beyond routine calibration and battery replacements

where applicable, our products require no user

maintenance. Clean electrical connectors, housings, and

mounting surfaces with solutions and techniques that will

not harm the material of construction. Observe caution

when using liquids near devices that are not hermetically

sealed. Such devices should only be wiped with a

dampened cloth—never saturated or submerged.

In the event that equipment becomes damaged or ceases

to operate, our Application Engineers are here to support

your troubleshooting efforts 24 hours a day, 7 days a

week. Call or email with model and serial number as well

as a brief description of the problem.

Calibration

Routine calibration of sensors and associated

instrumentation is necessary to maintain measurement

accuracy. We recommend calibrating on an annual basis,

after exposure to any extreme environmental influence,

or prior to any critical test.

PCB Piezotronics is an ISO-9001 certified company whose

calibration services are accredited by A2LA to ISO/IEC

17025, with full traceability to SI through N.I.S.T. In

addition to our standard calibration services, we also offer

specialized tests, including: sensitivity at elevated or

cryogenic temperatures, phase response, extended high

or low frequency response, extended range, leak testing,

hydrostatic pressure testing, and others. For more

information, contact your local PCB Piezotronics

distributor, sales representative, or factory customer

service representative.

Returning Equipment

If factory repair is required, our representatives will

provide you with a Return Material Authorization (RMA)

number, which we use to reference any information you

have already provided and expedite the repair process.

This number should be clearly marked on the outside of

all returned package(s) and on any packing list(s)

accompanying the shipment.

Contact Information

PCB Piezotronics, Inc.

3425 Walden Ave.

Depew, NY14043 USA

Toll-free: (800) 828-8840

24-hour SensorLine: (716) 684-0001

General inquiries: in[email protected]

Repair inquiries: rma@pcb.com

For a complete list of distributors, global offices and sales

representatives, visit our website, www.pcb.com.

Safety Considerations

This product is intended for use by qualified personnel

who recognize shock hazards and are familiar with the

precautions required to avoid injury. While our equipment

is designed with user safety in mind, the protection

provided by the equipment may be impaired if equipment

is used in a manner not specified by this manual.

Discontinue use and contact our 24-Hour Sensorline if:

Assistance is needed to safely operate equipment

Damage is visible or suspected

Equipment fails or malfunctions

For complete equipment ratings, refer to the enclosed

specification sheet for your product.

Definition of Terms and Symbols

The following symbols may be used in this manual:

DANGER

Indicates an immediate hazardous

situation, which, if not avoided, may

result in death or serious injury.

Manual 21354 Rev E

ECN 50523

CAUTION

Refers to hazards that could damage

the instrument.

NOTE

Indicates tips, recommendations and

important information. The notes

simplify processes and contain

additional information on particular

operating steps.

The following symbols may be found on the equipment

described in this manual:

This symbol on the unit indicates that

high voltage may be present. Use

standard safety precautions to avoid

personal contact with this voltage.

This symbol on the unit indicates that

the user should refer to the operating

instructions located in the manual.

This symbol indicates safety, earth

ground.

Manual 21354 Rev E

ECN 50523

PCB工业监视和测量设备 - 中国RoHS2公布表

PCB Industrial Monitoring and Measuring Equipment - China RoHS 2 Disclosure Table

部件名称

有害物质

铅(Pb)

汞

(Hg)

镉

(Cd)

六价铬(Cr(VI))

多溴联苯 (PBB)

多溴二苯醚(PBDE)

住房

PCB板

电气连接器

压电晶体

环氧

铁氟龙

电子

厚膜基板

电线

电缆

塑料

焊接

铜合金/黄铜

本表格依据 SJ/T 11364 的规定编制。

O：表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572 规定的限量要求以下。

X：表示该有害物质至少在该部件的某一均质材料中的含量超出 GB/T 26572 规定的限量要求。

铅是欧洲RoHS指令2011/65/ EU附件三和附件四目前由于允许的豁免。

CHINA RoHS COMPLIANCE

Manual 21354 Rev E

ECN 50523

Component Name

Hazardous Substances

Lead (Pb)

Mercury (Hg)

Cadmium (Cd)

Chromium VI

Compounds

(Cr(VI))

Polybrominated

Biphenyls (PBB)

Polybrominated

Diphenyl Ethers

(PBDE)

Housing

PCB Board

Electrical Connectors

Piezoelectric Crystals

Epoxy

Teflon

Electronics

Thick Film Substrate

Wires

Cables

Plastic

Solder

Copper Alloy/Brass

This table is prepared in accordance with the provisions of SJ/T 11364.

O: Indicates that said hazardous substance contained in all of the homogeneous materials for this part is below the limit

requirement of GB/T 26572.

X: Indicates that said hazardous substance contained in at least one of the homogeneous materials for this part is above the limit

requirement of GB/T 26572.

Lead is present due to allowed exemption in Annex III or Annex IV of the European RoHS Directive 2011/65/EU.



PCB PIEZOTRONICS, INC. 3425 WALDEN AVENUE DEPEW, NY 14043-2495 PHONE 716-684-0001 FAX 716-684-0987

®ICP is a registered trademark of PCB Group, Inc. KS398

Manual Number: 63496

Manual Revision: B

ECO Number: 47035

SIGNAL CONDITIONER

Model 482C24

GENERAL OPERATION

MANUAL

For powering ICP®sensors and remote charge convertors, this signal conditioner provides an

effective method for managing small numbers of sensor channels. A simple command set, entered

through industry standard interface, allows the user to generate powerful application-specific

programs to automate system testing.

This manual describes the functions and features of model 482C24.

Table of Contents

Table of Contents i

1-0 INTRODUCTION AND SPECIFICATIONS 1

1-1 Introduction: Safety Considerations 1

1-2 Model 482C24 System Description 2

1-2.1 Model 482C24 ICP®Input/ Output Mode 2

1-3 Block Diagram 2

1-4 Installation 3

1-4.1 Grounding Techniques 3

1-4.2 Quick Set-up Instructions 3

1-5 Operation: Standard AC Line 5

1-6 Maintenance and Repair 6

2-0 FRONT PANEL MODULE CONTROL 6

2-1 Introduction 6

2-2 Unit Initialization 6

2-3 Main Menu Format 6

2-4 Submenu Format and Command Selections 7

Reference 17

3-0 THEORY OF OPERATION 17

3-1 Sensor Excitation 17

3-2 Input Protection 18

3-3 Input Fault Detection 18

3-4 Input Interface 18

3-5 Normalized Output Sensitivity 18

3-6 Overload Detection and Autoscaling 19

3-6.1 Auto scaling 19

3-6.2 Overload 19

3-7 Connector Configuration 20

3-8 RS-232 Interface 20

3-9 Non-Volatile Memory 20

3-10 Transducer Electronic Data Sheet (TEDS) Interface 20

4-0 COMPUTER INTERFACE PROGRAMMING GUIDE 20

4-1 Introduction 20

4-2 RS-232 21

MULTICHANNEL SIGNAL CONDITIONER MODEL 482C24 GENERAL OPERATION MANUAL

4-3 RS-232 Host Set-Up 21

4-4 RS-232 Rear Panel Pin out Listing 21

4-5 Ethernet Communication 21

4-6 Communication Guidelines 21

4-7 Unit Initialization Procedure 22

4-8 Command Summary 22

4-9 Command Format 23

4-10 Commands 23

GAIN 23

SENS 24

FSCI 24

FSCO 25

INPT 25

IEXC 26

FLTR 26

OFLT 26

CLMP 27

CPLG 27

AZZR 27

VEXC 28

CALB 28

RTED 29

WTED 30

ALLC 30

RBIA 31

CHRD 31

SWOT 31

STUS 32

UNIT 32

UNID 33

LEDS 34

RSET 34

AUTR 35

SAVS 35

MULTICHANNEL SIGNAL CONDITIONER MODEL 482C24 GENERAL OPERATION MANUAL

iii

Communication Responses 35

Figure 1 Generic Block Diagram of series 482C................................................2

Figure 2 ICP®Sensor Excitation........................................................................17

Figure 3 Input Fault Window Comparator with LED Indicator.......................18

Figure 4 Input Amplifier Configuration.............................................................18

Figure 5 Autoscale/Overload Window Comparator........................................19

Figure 6 RS-232 Configuration..........................................................................20

MULTICHANNEL SIGNAL CONDITIONER MODEL 482C24 GENERAL OPERATION MANUAL

1-0. INTRODUCTION AND SPECIFICATIONS

1-1. Introduction: Safety Considerations

WARNING SYMBOLS AND TERMS

The following symbols and terms may be found on the equipment described in this manual.

This symbol on the unit indicates that the user should refer to the operating instructions located in the manual.

This symbol on the unit indicates that high voltage may be present. Use standard safety precautions to avoid

personal contact with this voltage.

This symbol indicates that the test fixture, Model 482C24, must be connected to earth ground via the power cord.

The WARNING heading used in this manual explains dangers that might result in personal injury or death. Always

read the associated information very carefully before performing the indicated procedure.

The Caution heading used in this manual explains hazards that could damage the instrument.

WARNING 1: The power supply/signal conditioner should not be opened by anyone other than qualified service

personnel. This product is intended for service by qualified personnel who recognize shock hazards and are familiar

with the safety precautions required to avoid injury.

WARNING 2: This equipment is designed with user safety in mind; however, the protection provided by the equipment

may be impaired if the equipment is used in a manner not specified by PCB Piezotronics, Inc.

Caution 1: Cables can kill your equipment. High voltage ElectroStatic Discharge (ESD) can damage electrical devices.

Similar to a capacitor, a cable can hold a charge caused by triboelectric transfer, such as that which occurs in the

following:

Laying on and moving across a rug.

Any movement through air.

The action of rolling out a cable.

Contact to a non-grounded person

The solution for product safety: 1) Connect the cables only with the AC power off. 2) Temporarily “short” the end of

the cable before attaching it to any signal input or output.

Caution 2: ESD considerations should be made prior to performing any internal adjustments on the equipment. Any

piece of electronic equipment is vulnerable to ESD when opened for adjustments. Internal adjustments should therefore

be done ONLY at an ESD-safe work area. Many products have ESD protection, but the level of protection may be

exceeded by extremely high voltage that is typically present in normal situations.

EQUIPMENT RATINGS

For complete specifications, please refer to the enclosed Specification Sheet. This equipment operates optimally at +32

to +120°F (0 to +50°C), in an environment having <85% relative humidity. Its line power frequency range is 50/60 Hz.

482C24 requires 10-15 VDC with 500 mA to operate. The unit receives power from a supplied 12 VDC universal AC

power adaptor.

Table des matières

Autres manuels PCB Piezotronics Équipement de test

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 482B11 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics VIBRATION DIVISION GK291D05 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 8159-0045B Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 394A10 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 498A-0093 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 483C30 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics Larson Davis CAL250 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics ICP 410C01 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 482C05 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 394A11 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics ICP Y482A22/NP Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 301A03 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics Modular Series Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 8159-0013A Manuel utilisateur

PCB Piezotronics

PCB Piezotronics F8159-1012A Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 301A04 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 8159-1112A Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 8159-0051A Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 8159-0153A Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 118B06 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 088A Manuel utilisateur

PCB Piezotronics

PCB Piezotronics IMI SENSORS 699A05 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics IMI SENSORS 682A14 Mode d’emploi

Manuels Équipement de test populaires d'autres marques

SMART

SMART KANAAD SBT XTREME 3G Series Manuel utilisateur

Agilent Technologies

Agilent Technologies BERT Serial Manuel utilisateur

Agilent Technologies

Agilent Technologies N3280A Manuel utilisateur

Vernier

Vernier Go Direct Voltage Manuel utilisateur

Lifeloc

Lifeloc R.A.D.A.R. Manuel utilisateur

Fluke

Fluke T5-600 Instructions d'utilisation et d'installation

Mercury

Mercury TSL01 Manuel utilisateur

MAHA

MAHA MBT Series Manuel utilisateur

Fuji Electric

Fuji Electric P-61 Manuel utilisateur

ETC

ETC SealerAtor Manuel utilisateur

Skyfine

Skyfine ETHYWAY V2 Manuel utilisateur

Appion

Appion G5 Twin Manuel utilisateur

BW Technologies

BW Technologies MicroDock II Manuel utilisateur

Sun Nuclear

Sun Nuclear 1027 Manuel utilisateur

Biomark

Biomark HPR LITE READER Manuel utilisateur

Hioki

Hioki 3169-20 Manuel utilisateur

Ashcroft

Ashcroft ATE-100 Manuel utilisateur

Rohde & Schwarz

Rohde & Schwarz RTA4000 Manuel utilisateur