Patton electronics OnSite 1052 Series Manuel utilisateur

OnSite 1052 & 1063 Series

Metro-Optical Transport Access

Nodes

Quick Start Guide

Important

—

This is a Class A device and isnot intended for use in a residential environment.

Part Number: 07MOS10xx-QS, Rev. C

Revised: February 20, 2012

Sales Office: +1 (301) 975-1000

Technical Support: +1 (301) 975-1007

E-mail: support@patton.com

WWW: www.patton.com

2OnSite Series Quick Start Guide

• Do not open the device when the power cord is connected. For sys-

tems without a power switch and without an external power

adapter, line voltages are present within the device when the power

cord is connected.

• For devices with an external power adapter, the power adapter shall

be a listed Limited Power Source The mains outlet that is utilized to

power the device shall be within 10 feet (3 meters) of the device,

shall be easily accessible, and protected by a circuit breaker in compli-

ance with local regulatory requirements.

• For AC powered devices, ensure that the power cable used meets all

applicable standards for the country in which it is to be installed.

• For AC powered devices which have 3 conductor power plugs (L1, L2

& GND or Hot, Neutral & Safety/Protective Ground), the wall outlet

(or socket) must have an earth ground.

• For DC powered devices, ensure that the interconnecting cables are

rated for proper voltage, current, anticipated temperature, flammabil-

ity, and mechanical serviceability.

• WAN, LAN & PSTN ports (connections) may have hazardous voltages

present regardless of whether the device is powered ON or OFF.

PSTN relates to interfaces such as telephone lines, FXS, FXO, DSL,

xDSL, T1, E1, ISDN, Voice, etc. These are known as “hazardous net-

work voltages” and to avoid electric shock use caution when working

near these ports. When disconnecting cables for these ports, detach

the far end connection first.

• Do not work on the device or connect or disconnect cables during peri-

ods of lightning activity.

This device contains no user serviceable parts. This device can only be

repaired by qualified service personnel.

If one has reason to open the chassis or case, then the precautions men-

tioned above shall be followed. This includes both the warnings relating

to disconnection of the input power, and the warnings relating to the dis-

connection of WAN, LAN & PSTN ports.

This device is NOT intended nor approved for connection to the PSTN. It

is intended only for connection to customer premise equipment.

WARNING

OnSite Series Quick Start Guide 3

1.0 Unpacking and Installation

1. Check the contents of the shipping container and accessories box or bag against the content list and the

packing slip. Verify that you received all listed equipment and inspect all items for shipping damage.

2. Unpack the OS-10 Series chassis and install it into a rack according to the instructions in the OnSite Series

User Manual available online at www.patton.com/manuals/OS10xx.pdf.

3. Verify that the site where you wish to install and operate the equipment conforms to the environmental

requirements in the OnSite Series User Manual.

2.0 Powering Up the System

If your OS-10 Series system was ordered for use with AC power, follow these steps:

1. Connect the enclosed AC power cable to the AC power receptacle on the rear side of the OS-10 Series

chassis.

2. Connect the power cable plug to an AC power source with the following characteristics: 15 A at 120 VAC

(60 Hz) or 10 A at 240 VAC (50 Hz) circuit with overcurrent protection.

Refer to the OS-10 Series Installation and Operation Guide if your system was ordered for use with DC power (–

48 VDC nominal).

When you first apply power to the system, the STAT (status) LED on the front panel becomes a solid amber light.

This light indicates that the system is booting. The STAT LED becomes a solid green light when the system com-

pletes the boot process and is ready for management access and operation.

Electrostatic Discharge (ESD) can damage equipment and impair electrical

circuitry. It occurs when electronic printed circuit cards are improperly

handled and can result in complete or intermittent failures. Do the follow-

ing to prevent ESD:

• Always follow ESD prevention procedures when removing and replac-

ing cards.

• Wear an ESD-preventive wrist strap, ensuring that it makes good

skin contact. Connect the clip to an unpainted surface of the chassis

frame to safely channel unwanted ESD voltages to ground.

• To properly guard against ESD damage and shocks, the wrist strap

and cord must operate effectively. If no wrist strap is available,

ground yourself by touching the metal part of the chassis.

CAUTION

4OnSite Series Quick Start Guide

3.0 Accessing and Configuring the System

To access the system management functions for the first time, your may use either the SERIAL or the Ethernet

LAN management port. Refer to the Installation and Operation Guide for access through the SERIAL port.

For first time access through the Ethernet LAN management port, follow these steps:

1. Connect a PC to the Ethernet LAN management port using the RJ-45 connector.

2. Configure the PC to connect to the OS-10 Series system using the factory default settings for the Ethernet

LAN management port.

Note By default, the IP address is set to 192.168.2.100.

3. Launch the Web browser of your choice, and type the default IP address of the system in the Address field

of the browser.

4. Log in to the OS-10 Series system using the super user ID and password.

Note The factory-assigned default password for the Super user is super (all lowercase letters).

Once you gain access to the system using the default settings, change the IP settings for the LAN port for secure

access to the system.

3.1 Changing the IP Settings for the LAN port

To configure the Ethernet LAN management port settings, follow these steps:

1. Select the SYSTEM folder from the OnSight Device Manager (DM) web-based GUI navigation menu.

2. From the expanded SYSTEM folder, select Management Access, and from this folder select LAN.

3. On the Ethernet LAN Management Port page, type the new LAN IP Address.

Note The Admin Status for the Ethernet LAN management port is always enabled.

4. Click on Apply.

The new IP settings take effect once you click on the Apply button. This change in settings causes the loss of

access connectivity to the system. You can regain access immediately by typing the new IP address of the LAN

port in the Address field of the browser. (Make sure that you change your PC settings to allow connectivity to the

OS-10 Series system over the same IP subnetwork.)

You will need to save the system configuration to avoid losing the new IP settings after a subsequent reboot.

Note The system uses the last saved configuration to restore system operation and traffic connectivity after

the completion of the reboot. Any recent configuration data and connections not saved to the system

configuration file are lost and need re-entry, if required.

OnSite Series Quick Start Guide 5

3.2 Saving the System Configuration

To save the system configuration to the flash memory, follow these steps:

1. Select the SYSTEM folder from the OnSight DM web-based GUI navigation menu.

2. From the expanded SYSTEM folder, select the Actions folder.

3. From the expanded Actions folder, select Save Configuration.

A warning window opens to alert you to the start of the save-configuration process. Click on OK to continue or

Cancel to cancel the request.

4.0 Additional Information

The system is now ready for operation using the OnSight DM web-based graphical user interface (GUI). You may

now configure the system clock, timing mode and STM-1 interface settings for your intended application.

For detailed instructions, refer to the OnSite Series User Manual and the OnSite Series Administrator’s Reference

Guide available online at www.patton.com/manuals/OS10xx.pdf and www.patton.com/manuals/

OS10xx-arg.pdf.

A.0 Customer and Technical Support

Online support: www.patton.com

E-mail support: s[email protected]m—answered within 1 business day

Telephone support:

•

Standard: +1 (301) 975-1007 (USA), Monday–Friday: 8:00 am to 5:00 pm EST (1300 to

2200 UTC/GMT)

•

Alternate: +41 (0)31 985 25 55 (Switzerland), Monday–Friday: 8:00 am to 5:00 pm CET (0900 to 1800

UTC/GMT)

Fax: +1 (253) 663-5693 (USA) or +41 (0)31 985 25 26 (Switzerland)

6OnSite Series Quick Start Guide

B.0 Compliance Information

B.1 Compliance

EMC Compliance:

•

EN55022, Class A

•

EN55024

Low-Voltage Directive (Safety Compliance):

•

IEC/EN60950-1

PSTN:

•

This device is not intended nor approved for connection to the PSTN.

B.2 CE Declaration of Conformity

Patton Electronics, Inc declares that this device is in compliance with the essential requirements and other rele-

vant provisions of Directive 2004/108/EC relating to electromagnetic compatibility and Directive 2006/95/EC

relating to electrical equipment designed for use within certain voltage limits. The Declaration of Conformity

may be obtained from Patton Electronics, Inc at www.patton.com/certifications.

The safety advice in the documentation accompanying this device shall be obeyed. The conformity to the above

directive is indicated by CE mark on the device.

B.3 Authorized European Representative

D R M Green

European Compliance Services Limited.

Avalon House, Marcham Road

Abingdon,

Oxon OX14 1UD, UK

OnSite Series Quick Start Guide 7

The information in this document is subject to change without notice. Patton Electronics assumes no

liability for errors that may appear in this document.

Trademarks statement

The term OnSite is a trademark of Patton Electronics Company. All other trademarks presented in this document

are the property of their respective owners.

Warranty, Trademark, & Compliance Information

For warranty, trademark and compliance information, refer to the OnSite Series User Manual located online

at www.patton.com/manuals.

In accordance with the requirements of council directive 2002/96/EC on Waste of

Electrical and Electronic Equipment (WEEE), ensure that at end-of-life you separate

this product from other waste and scrap and deliver to the WEEE collection system in

your country for recycling.

8OnSite Series Quick Start Guide

NOTES

____________________________________________________________________

Autres manuels pour OnSite 1052 Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Patton electronics Routeur réseau

Patton electronics

Patton electronics Patton IPLink 2603 Manuel utilisateur

Patton electronics

Patton electronics SmartNode 07MSN5200-QS Manuel utilisateur

Patton electronics

Patton electronics SMARTNODE 4630 Series Manuel utilisateur

Patton electronics

Patton electronics SMARTNODE 4110 Series Manuel utilisateur

Patton electronics

Patton electronics ONSITE 2603 Manuel utilisateur

Patton electronics

Patton electronics ENVIRONET EHA3201 Manuel utilisateur

Patton electronics

Patton electronics 3224 Diamond Edge Manuel utilisateur

Patton electronics

Patton electronics Patton IPLink 2603 Manuel utilisateur

Patton electronics

Patton electronics ONSITE 2603 Manuel utilisateur

Patton electronics

Patton electronics 4520 Manuel utilisateur

Patton electronics

Patton electronics IM1/I4 Manuel utilisateur

Patton electronics

Patton electronics SmartNode 4830 Series Manuel utilisateur

Patton electronics

Patton electronics IM2RC/IA Manuel utilisateur

Patton electronics

Patton electronics SmartLink 4020 Series Manuel utilisateur

Patton electronics

Patton electronics SmartNode 4520 Series Manuel utilisateur

Patton electronics

Patton electronics 2135 Manuel utilisateur

Patton electronics

Patton electronics 4630 Series Manuel utilisateur

Patton electronics

Patton electronics SmartNode 4900 Series Manuel utilisateur

Patton electronics

Patton electronics SmartNode 4960 Series Manuel utilisateur

Patton electronics

Patton electronics SmartNode 4634 Series Manuel utilisateur

Patton electronics

Patton electronics OnSite 3210 Series Manuel utilisateur

Patton electronics

Patton electronics SMARTNODE 4900 Manuel utilisateur

Patton electronics

Patton electronics 4900 Series Manuel utilisateur

Patton electronics

Patton electronics Patton IPLink 2635 Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

TP-Link

TP-Link TD-8817 Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité