Paslode 30 Degree Manuel

30 Cordless Framing Nailer

Cleaning Procedure

Tool Cordless Tool Cleaner/Degreaser Paslode Cordless Lubricating Oil

(USA and Canada)Part No. 401482(USA)Part No. 219348

Part No. 401331

5/32" Hex Key Wrench

905624-1

09/15

This procedure provides a simple but effective way to

clean your Paslode Cordless Framing Nailer and main-

tain reliable operation. Regular cleaning and lubrication

will also extend part life and provide maximum nail

driving power.

Only

one

tool

necessary

disassemble the

Paslode

Cordless

Framing

Nailer

preparation

for

cleaning:

the

5/32"

hex

key

wrench

provided

with

the

Paslode

Cord -

less Framing Nailer.

Paslode

recommends

that

an aerosol

"Cleaner/Degreaser”

Paslode® Cordless

Tool

Cleaner

(Part No. 219348),

(Canada use Part No. 219086) (Australia, New Zealand

use Part No. B20544L)

This

cleaner

available through your local Paslode Dealer.

If a different type of cleaner is selected, make sure that

it will not damage plastic, rubber or electronic compo-

nents. Chemical damage to these materials or compo-

nents may result in the tool being made inoperable.

Although "safety" cleaners generally provide reduced

risk of fire and are more stable than other cleaners, they

cannot be handled carelessly. Always follow the manu-

facturer's instructions and never spray cleaner on the

Paslode Cordless Framing Nailer, unless the tool has

been allowed to cool down.

To begin, you will need the following items:

(Canada) Part No. 219086

be used for cleaning.

(ANZ)Part No. B20544F

(ANZ) Part No. B20544L

DANGER

Never operate the Paslode Cordless Framing nailer unless all

four Socket Head Cap Screws are firmly tightened on the

cylinder head. Failure to do this could result in tool damage,

fire and personal injury.

Handle-Magazine Removal

DANGER

Remove all fasteners, fuel, and battery prior to servicing tool.

Step 1

Using the 5/32" Hex Key Wrench (# 401331) remove

the Handle-Magazine Assembly by removing the two

#10-24 x 1-1/8" long Socket Head Cap screws from the

nose piece of the tool and pivot the Handle-Magazine

Assembly away from the Motor Assembly

Step 2

Remove the grille and air filter. Clean them in soapy

water or with Paslode Cordless Tool Cleaner/Degreaser.

Step 3

Remove the cap and air filter by unscrewing the four

#10-24 Socket Head Cap Screws.

Screws

Grille

Filter

Handle-Magazine Removal

Step 4

Carefully tilt the Handle-Magazine Assembly away

from the Motor Assembly and gently pull the two

assemblies apart. CAUTION: Use care to ensure that

the fan does not scratch the combustion chamber.

Also be careful when setting the Handle-Magazine

Assembly down so that you do not damage the fan

blades or bend the fan motor shaft.

You have now separated the tool into two major as-

semblies, allowing access to the areas that require

periodic cleaning and lubrication.

Step 1

Spray the Cylinder Head with cleaner/degreaser.

Allow the dirt and debris to drip off.

CLEANER/DEGREASER RUN INTO THE

HANDLE.

Step 2

Using a clean, lint-free rag, wipe off any remaining

cleaner or dirt. Make sure the Seal Rings and

Spark Plug are completely clean and clear of de-

bris. Repeat Step 3 to remove any heavy deposits

or remaining residue.

Step 3

Thoroughly lubricate the Seal Rings with Paslode

Cordless Lubricating Oil,

part #401482. Make

sure oil is applied evenly around entire

Seal Ring.

Set the Handle/Cylinder Head Assembly aside.

Note:

Paslode Cordless Lubricating Oil is specially

formulated for use in the Paslode Cordless

Nailer. The use of other types of lubri-

cants may cause rapid build-up of combustion

residue or result in premature part failure.

Cylinder Head

Framing

DO NOT LET OVER SPRAY OR DIRTY

Before reassembly, ensure the position of the

away from each other, after lubricating.

gap of the 2 X seal rings are 180 degrees, facing

Motor Assembly

Step 1

Push the Piston Assembly to the "down" position

using the handle portion of the screwdri

ver or a clean

piece of wood.

Step 2

Spray a liberal amount of Cordless Tool Cleaner into

the inside of Sleeve and Combustion Chamber. Invert

Motor Assembly, and let excess cleaner and dirt drain

Step 3

Using a clean area of a lint-free rag, wipe off any

remaining cleaner or dirt. Repeat Step 2 to remove

any heavy deposits or remaining residue.

out.

Motor Assembly

Step 4

With Motor Assembly tilted up, squeeze 4-5 drops

of oil into Sleeve (Area "A") and 5-6 drops onto lower

lip of Combustion Chamber

(Area "B"). Rotate

Motor Assembly while oiling to ensure oil is evenly

distributed around Sleeve

and lip. See Tool Cutaway

Illustration,page 7.

Step 5

Hold Motor Assembly upright, and push down and

release several times to allow oil on lower lip of

Combustion Chamber to be evenly distributed.

Step 6

Manually push the Driver Blade up and down to

distribute the oil in the Sleeve evenly.

Before reassembly, manually push the driver

back up to the top.

Motor Assembly

Step 7

Tilt the Motor Assembly upright, and apply 3-4

drops of Paslode Cordless Lubricating Oil evenly

spaced around the top of the Combustion Chamber

(Area "C"). Spread the oil using your fingertip.

Step 8

Reassemble the

Paslode Cordless Framing Nailer

following disassembly Steps 1-3, page 2 i

n Reverse

order.

DANGER

Do not attempt to operate the tool unless the head

screws, filter and cap are securely attached to the

housing. Operating the Paslode Cordless Framing

nailer with loose or missing head screws can result

in the escape of burning gases, tool damage, and

injury to tool user and property.

Combustion

Chamber

Sleeve

Piston

Assembly

"Mid-Check"

Area

NOTE: After the tool is completely

assembled and all screws are tightened,

test the tool for proper operation. Some

smoke may be noticeable from the

exhaust ports on the first few cycles as

excess oil is burned off. Consult the

Operating Manual for instructions if the

tool malfunctions.

The maintenance interval for cleaning the Paslode

Cordless Framing Nailer will vary depending upon

the number of nails driven, and the operating con-

ditions under which the tool is used. When the

Paslode Cordless Framing Nailer

dirty environment or at high nailing rates for extend-

ed periods,cleaning should be performed at

intervals.

Paslode has developed this chart as a guideline to

assist you in establishing the proper cleaning

schedule for the type of use the tool is getting. If

find that the suggested cleaning interval is al-

the tool to become excessively dirty between

cleanings, reduce the interval to the next shorter

frequency. If it is apparent that the

Paslode Cord-

less Frami

ng Nailer is not in need of cleaning

at the scheduled time, increase the interval to the

next longer period.

If you have any questions regarding this chart or any

of the instructions in this cleaning procedure, contact

your Paslode representative for assistance.

30 Cordless Framing Nailer

Cleaning Procedure

OPERATING CONDITIONS

CLEAN DIRTY

MODERATE VERY DIRTY

50000

40000

30000

20000

used in a

shorter

you

lowing

120 Travail Road.Markham, ONL3S 3J1

www.paslode.ca

Canada

A Division of ITW Australia Pty Ltd

ABN 63 004 235 063

PO Box 914

Ingleburn,1890

www.paslode.com.au

Australia

A Division of ITW New Zealand Ltd

PO Box 100 303 NSMC

Aukland, New Zealand

www.paslode.co.nz

New Zealand

USA

An Illinois Tool Works Co.

155 Harlem Avenue

Glenview, IL 60025

www.paslode.com

P P P

Clavadora Paslode 30

Cordless

Procedimiento de limpieza

Para comenzar, necesita lo siguiente:

Herramienta Limpiador Aceite lubricante Paslode®

Pieza N°401482

Pieza N°219348

Pieza N°401331

5/32" Hex Key Wrench

Este procedimiento representa una forma sencilla pero

eficiente de limpiar su clavadora para que mantenga

un funcionamiento confiable. La limpieza y la lubri-

cación regulares de la clavadora también prolongan la

duración de las piezas que la forman y permiten

una máxima potencia para clavar.

Para poder limpiar su clavadora, sólo necesita una

herramienta, la llave Allen (llave de cabeza hexago-

nal) de 5/32 plg. que se entrega junto con su

clavadora Impulse.

Paslode recomienda que use un limpiador en aerosol,

tal como el "limpiador de seguridad" Paslode (No.

219348). Este limpiador está disponible a través de su

representante Paslode.

Si un tipo de desengrasador distincto al recomen-

dado es usado, asegúrese que esto no dañará el

plástico, las gomas o los componentes eléctricos.

Daño químico a éstos los materiales o los compo-

nentes pueden causar el instrumento sea hecho

inoperable.

Aunque limpiadores de seguridad generalmente redu-

cen el riesgo de fuego y son mas estable queotros

limpiad-ores, no deben ser usados sin cuidado.

Siempre sigua las instrucciones de la fabrica y no use

el limpiador en la clavadora hasta que la herramienta

este enfriada.

PELIGRO

Se deben guitar todos los sujetadores, el cartucho de gas y ta

batería antes de reparar la herramienta.

Paso 1

Usando la llave Allen de 5/32 plg. (#401331) quite el

conjunto del mango y el mecanismo de alimentacion:

destornille los dos tornillos de casquete de boca

tubular #10-24 x 1-1/8 plg. y tire suavemente el

conjunto del mango y el mecanismo de alimentacion

alejándolo del conjunto del motor.

Paso 2

Quite la cubierta y el filtro. Limpie los con aqua con

javon o con Paslode's Degreaser Cleaner.

Paso 3

Quite la tapa y el filtro y destornille los cuatro tornillos

de casquete de boca tubular #10-24.

Conjunto del mango y el mecanismo de alimentacion

Tornillos

PELIGRO

Nunca se debe hacer funcionar la clavadora a menos que los

cuatro tornillos de cabeza hueca estén apretados firmemente

en la tapa del cilindro. Si no se observa esta advertencia,

pueden ocasionarse daños a la herramienta, incendio y

heridas personales.

Cubierta

Filtro

Table des matières

Langues :

Autres manuels Paslode Cloueuse

Paslode

Paslode Impulse IM90CI Manuel utilisateur

Paslode

Paslode TrimMaster IM250A-Li Manuel utilisateur

Paslode

Paslode CNW45R Manuel utilisateur

Paslode

Paslode IM250S Manuel utilisateur

Paslode

Paslode FN1835 Manuel utilisateur

Paslode

Paslode FNS1850 Manuel utilisateur

Paslode

Paslode FN1565A34 Manuel utilisateur

Paslode

Paslode PSN90 Manuel utilisateur

Paslode

Paslode T250S-F16P Manuel utilisateur

Paslode

Paslode IM250A-Li2 Manuel utilisateur

Paslode

Paslode IM 350/90 CT Instructions d'installation

Paslode

Paslode T250A-F16 Manuel utilisateur

Paslode

Paslode FN1665.1 Manuel utilisateur

Paslode

Paslode FN 1665 Manuel utilisateur

Paslode

Paslode IM200Li.2 Manuel utilisateur

Paslode

Paslode PF350-S Manuel utilisateur

Paslode

Paslode T250-F16 Manuel utilisateur

Paslode

Paslode IM350+ Lithium Manuel utilisateur

Paslode

Paslode DF90S Manuel utilisateur

Paslode

Paslode FN 1665 Manuel utilisateur

Paslode

Paslode 902600 Manuel utilisateur

Paslode

Paslode IM350+ Lithium Manuel utilisateur

Paslode

Paslode FN2265 Manuel utilisateur

Paslode

Paslode F150S-PP Manuel utilisateur

Manuels Cloueuse populaires d'autres marques

Performance Tool

Performance Tool M643 Manuel utilisateur

Hitachi

Hitachi VH650 - Fencing Nailer, Full Head Manuel utilisateur

Parkside

Parkside PET 25 B1 Manuel utilisateur

Senco

Senco Fusion Technology F-35XP Manuel utilisateur

Grizzly

Grizzly G1847 Manuel utilisateur

Ryobi

Ryobi R18N18G Manuel utilisateur

Black & Decker

Black & Decker 492848-00 Manuel utilisateur

HOLZMANN MASCHINEN

HOLZMANN MASCHINEN TN90 Manuel utilisateur

Metabo HPT

Metabo HPT NR 3690DC Mode d’emploi

Surtek

Surtek CN650 Dimensions et guide d'installation

Makita

Makita GF600 Manuel utilisateur

Parkside

Parkside PET 25 B1 Manuel utilisateur

Senco

Senco AirFree 25 Manuel utilisateur

Freeman

Freeman P50LSLW Manuel utilisateur

Aicon PRO

Aicon PRO DAC4507 Manuel utilisateur

DAJ

DAJ XR150A Manuel utilisateur

Makita

Makita AN923 Manuel utilisateur

Grizzly

Grizzly T20644 Manuel utilisateur