Parrot ANAFI Manuel utilisateur

How to assemble and

disassemble Anafi

ANAFI assembly and disassembly processes 2

Prerequisites

The best way to repair ANAFI is to use Parrot official drones repair kit. You will need the cruciform as

well as the Torx 5 (T5) in order to carry out this procedure.

Parrot repair kit

Anafi disassembly process

-Remove the battery from the drone.

-Gently unstick the sticker from the body of the drone.

ANAFI assembly and disassembly processes 3

-Remove both screws under the sticker and then quickly put the sticker back in position to

stop the glue from drying.

-Remove both screws from the bottom of the drone at the arms junction.

-Lift the bottom cover from the front of the drone, then push it toward the rear to remove it.

ANAFI assembly and disassembly processes 4

-Pull the ventilator to remove it from its slot and remove the LED connector, near the

ventilator.

-Remove antennas from the motherboard. Antennas on the middle of the motherboard are

linked to the rear feet; the side antennas are plugged to the front feet.

ANAFI assembly and disassembly processes 5

-Remove the plastic holder from the motherboard by pulling on the plastic stamp, then slide

the holder.

-Remove the gimbal connector from the motherboard.

-Unplug the micro coaxial wire from the motherboard.

ANAFI assembly and disassembly processes 6

-Remove the four rubbers gently: Parrot recommends you hold the motherboard during the

process, to stop rubbers from falling from their support. Once rubbers are removed, unplug

the GPS antenna which can be found on hidden face of the motherboard.

-Unstick the SD slot, then remove it by pulling it through the plastic structure’s hole.

ANAFI assembly and disassembly processes 7

-Remove the vertical camera from the support by pushing gently on it.

-Remove the three screws under each arm of the drone.

ANAFI assembly and disassembly processes 8

-Pull on the bottom cover of each arm to remove them.

-Remove the two screws from the GPS cover (orange circle) then push on the button above

located the gimbal to remove the cover (red circle).

ANAFI assembly and disassembly processes 9

-Remove the screws closest to the center of the GPS card.

-Remove the screws holding the hinges: a screw can be found at each extremity of the GPS

card. Do not forget to remove screws from the bottom of the drone as well.

-Retract the arms towards the body of the drone before removing the black plastic holder of

each hinge.

-Push the lower side of each hinge to remove them.

-Caution: a washer will fall off from each hinge when removed, make sure that you do not

lose them.

ANAFI assembly and disassembly processes 10

-Remove the plastic part which holds antennas by pulling the clips on each side of the part.

-Unplug motors by pulling the connectors out of their sockets.

-Caution: Do not pull on the wires.

-Remove the arms carefully, one after the other: make sure that antenna cables do not get

stuck with other cables.

Autres manuels pour ANAFI

5

Autres manuels Parrot Drone

Parrot

Parrot bebop 2 Manuel utilisateur

Parrot

Parrot DISCO-PRO AG Manuel utilisateur

Parrot

Parrot bebop 2 Manuel utilisateur

Parrot

Parrot Bebop Manuel utilisateur

Parrot

Parrot AR Manuel utilisateur

Parrot

Parrot Mambo Manuel utilisateur

Parrot

Parrot ANAFI Ai Manuel utilisateur

Parrot

Parrot BEBOP 2 POWER Manuel utilisateur

Parrot

Parrot SenseFly eBee Manuel utilisateur

Parrot

Parrot ANAFI Thermal Manuel utilisateur

Parrot

Parrot ANAFI Ai Manuel utilisateur

Parrot

Parrot ANAFI Ai Manuel utilisateur

Parrot

Parrot ANAFI Manuel utilisateur

Parrot

Parrot minidrones HYDROFOIL Manuel utilisateur

Parrot

Parrot Mambo Manuel utilisateur

Parrot

Parrot Bluegrass Manuel utilisateur

Parrot

Parrot ANAFI USA Manuel utilisateur

Parrot

Parrot minidrones NEWZ Manuel utilisateur

Parrot

Parrot Swing Manuel utilisateur

Parrot

Parrot Bebop-Pro Thermal Manuel utilisateur

Parrot

Parrot JUMPING RACE Manuel utilisateur

Parrot

Parrot NEWZ Manuel utilisateur

Parrot

Parrot ANAFI Manuel utilisateur

Parrot

Parrot BEBOP-PRO 3D MODELING Manuel utilisateur

Manuels Drone populaires d'autres marques

Ryze

Ryze Tello Manuel utilisateur

PowerVision

PowerVision PowerRay Manuel utilisateur

Force1

Force1 rogue F72 Manuel utilisateur

Zerotech

Zerotech DOBBY Manuel utilisateur

Protocol

Protocol VIDEODRONE AP Manuel utilisateur

dji

dji Matrice M210 Manuel utilisateur

MAKE

MAKE Terry Kilby Manuel utilisateur

SYMA

SYMA X440 Manuel utilisateur

RUKO

RUKO F11 Manuel utilisateur

SYMA

SYMA X5UW(720P) Manuel utilisateur

Dynali

Dynali 25 H Mode d’emploi

dji

dji PHANTOM 4 Manuel utilisateur

Atlas

Atlas AtlasPRO Manuel utilisateur

Twodots

Twodots TVVIN BOARD Manuel utilisateur

GDU

GDU SAGA Manuel utilisateur

Ares

Ares ETHOS QX 130 Manuel utilisateur

Walkera

Walkera ZHUN Manuel utilisateur

dji

dji WIND-4 Manuel utilisateur