Parker AC890PX Series Manuel utilisateur
Page 2 - 30
Parts List:
Chassis Assembly
LA501088UXXX
CS Module Control Cable
CM471462U002
STO PCB
AH471776U001
CP to CS Control Cable
CM471686U003
AC890PX Control Module
890CM
Blanking plates
LA501357U001
BA501301U002
BA501301U003
AC890 CS Module
LA471171UXXX
(optional)
Bracket x 2
BA501090
AC890 CD Module
LA471160UXXX x 3
Housing Bracket
BA501111
BA501112
AC890 CP module
LA471175UXXX
(optional)
Air duct
BA501114
BA501113
STO Feedback Cable
CM472271U002
Roof Vent
LA501358
STO Supply Cable
CM501215U001
Mounting Bracket
BA501092 x 2
STO connection Cable
LA501221
Mounting Bracket
BA501093
Module Control Cables
CM471297U002
CM471297U003
CM471297U004
Upper & Lower
Setting Plates
BA501120
Earth Wire Assembly
CM467679U001
TS8 Adaptor
BA501091 x 2
Module Power Cables
CM501601U100
CM501601U500
Also Included:
Grommets, screws, p clips, gasket strip, etc.
CM501600U200
CM501600U300
CM501600U400
Right & Left Side Panels
LA501220U001
LA501220U002
See page 23
(drawing no.
LA501088U000)
Page 3 - 30
Before starting assembly you must read the Safety Instructions at the
beginning of Product Manual HA501299U001 available from
www.parker.com/ssd.
1. Assemble cubicle ready for mounting AC890PX Frame M.
Notes:
The minimum required backpanel width is 600mm.
This product is intended to be mounted in an appropriate electrical enclosure in a vertical
position where it is not subject to excessive heat or vibration.
These instructions use a Rittal TS8 cubical. If the product is not to be mounted in a Rittal
cubical then refer to HG501237U001.
These instruction need to be used in conjunction with assembly drawing LA501088U000.
Co-ordinates for a Rittal TS8 or PS8 series 600mm back panel HG501140.
Punch or drill the required mounting holes into the cubicle backplate this drawing assumes
the use of M8 inserts.
The back panel must be mounted in the rear most position.
Page 4 - 30
2. Fit STO PCB Assembly AH471776U001 to retaining posts on the chassis.
This equipment contains electrostatic discharge (ESD) sensitive parts. Observe
static control precautions when handling, installing and servicing this product.
3. Mount the chassis into the cubicle.
Partially insert a M8 bolt (no washer) in the centre top
mounting hole.
Hang the chassis assembly from the single bolt by passing the bolt head through the large
central hole on the rear panel of the chassis. Chassis is 38kg thus lifting procedures must
be adhered to.
Fix to back panel in all 4 positions with M8
bolts and remove original hanging bolt.
Page 5 - 30
4. Install the module mounting rails. Use the top dowels to align and fit left (LA501220U001)
and right (LA501220U002) rail assembles, fix using M5 SEMs FY047651 (item 642), quantity
8 (torque setting 2.7Nm).
5. Fit lower left mounting bracket BA501092 (item 252) with M6 SEMs FY385692 (item 643),
quantity 4 (torque setting 4.5Nm).
Fixings
BA501092
Fixings
Page 6 - 30
6. Loosely fit TS8 adaptor bracket BA501090 (item 250) to lower left mounting bracket
BA501092 (item 252) with M6 SEMs FY385692 (item 643), quantity 2. Loosely fit to cubicle
frame using TORX self tap screws FY501218 (item 645), quantity 2 (use upper hole positions)
(torque setting 4.5Nm).
7. Fit lower right mounting bracket BA501093 (item 253) with M6 SEMs FY385692 (item 643),
quantity 4 (torque setting 4.5Nm).
BA501090
BA501093
Fixings
Page 7 - 30
8. Loosely fit TS8 adaptor bracket BA501091 (item 251) to lower right mounting bracket
BA501093 (item 253) with M6 SEMs FY385692 (torque setting 4.5Nm) (item 643), quantity 3.
Loosely fit to cubicle frame using TORX self tap screws FY501218 (torque setting 2.7Nm)
(item 645), quantity 2 (use upper hole positions).
9. Fit lower setting plate BA501120 (item258) with self tap screws FY501150 (item 640),
quantity 6.
Tighten screws on TS8 adaptor bracket BA501091 (item 251) and TS8 adaptor bracket
BA501090 (item 250), on right and left sides, quantity 5. Tighten TORX self tap screws
FY501218 (item 645) slots towards the back, on both left and right sides, quantity 6.
Slots
Fixings
Page 8 - 30
10. Fit upper left mounting bracket BA501092 (item 252) with M6 SEMs FY385692 (torque
setting 4.5Nm) (item 643), quantity 4. Fix earth wire assembly CM467679U001 (item 285)
with front top screw, as shown.
Fit control housing bracket BA501111 (item 259) to left mounting bracket BA501092 (item
252) with M4 SEMs FY385968 (item 644), quantity 2.
Add grommet DF044535 (item 431) to mounting bracket BA501092 (item 252), this grommet
only has wires passing through it when it is configured as a parallel stack.
11. Loosely fit TS8 adaptor bracket BA501090 (item 250) to upper left mounting bracket
BA501092 (item 252) with M6 SEMs FY385692 (item 643), quantity 2. Loosely fit to cubicle
frame using TORX self tap screws FY501218 (item 645), quantity 2 (use lower hole
positions).
CM4674679U001
BA501090
Page 9 - 30
12. Fit upper right mounting bracket BA501093 (item 253) with M6 SEMs FY385692 (item
643), quantity 4. Fit control housing bracket BA501112 (item 260) to upper right mounting
bracket BA501093 (item 253) with M4 SEMs FY385968 (torque setting 1.3Nm) (item 643),
quantity 2.
13. Loosely fit TS8 adaptor bracket BA501091 (item 251) to upper right mounting bracket
BA501093 (item 253) with M6 SEMs FY385692 (item 643), quantity 3. Loosely fit to cubicle
frame using TORX self tap screws FY501218 (item 645), quantity 2 (use lower hole
positions).
BA501092
BA501091
Page 10 - 30
14. Fit upper setting plate BA501120 (item 258) with self tap screws FY501150 (item 640),
quantity 6 (slots to the rear).
Tighten screws on TS8 adaptor bracket BA501091 (item 251) and TS8 adaptor bracket
BA501090 (item 250), quantity 5. Tighten TORX self tap screws FY501218 (torque setting
2.7Nm) (item 645) on both sides, quantity 4.
BA501120
Autres manuels pour AC890PX Series
4
Table des matières
Autres manuels Parker Contrôleurs
Parker
Parker 890 Series Manuel d'instructions
Parker
Parker A4AP-DN Manuel
Parker
Parker 690+ series Manuel utilisateur
Parker
Parker AC30V Series Manuel utilisateur
Parker
Parker Compax3 Fluid T40 Manuel utilisateur
Parker
Parker Sporlan PSK Series Manuel utilisateur
Parker
Parker Compax3F Fluid Manuel utilisateur
Parker
Parker 650G Frame 1 Manuel utilisateur
Parker
Parker GEM6K Series Manuel
Parker
Parker Compumotor 6000 Series Manuel utilisateur
Parker
Parker ac890 Manuel utilisateur
Parker
Parker ERV Series Instructions d'utilisation et d'entretien
Parker
Parker 700-00028-0 Guide de configuration rapide
Parker
Parker ADAPTOMODE Series Instructions d'utilisation et d'installation
Parker
Parker AC30 series Manuel utilisateur
Parker
Parker LTR Series Fiche technique
Parker
Parker ER Series Fiche technique
Parker
Parker ER032 Fiche technique
Parker
Parker 8903/SP Manuel utilisateur
Parker
Parker X-Flow FM-1407 Guide de démarrage rapide
