Paradox Digiplex DGP-641 Manuel utilisateur
DGP-641 LCD Keypad (V1.3)
DGP-641ACC Access Control LCD Keypad
(V1.1)
Reference and Installation Manual
Digiplex LCD Keypad 1n
TABLE OF CONTENTS
1.0 Introduction....................................................... 4
1.1 SPECIFICATIONS........................................................ 5
2.0 Installation......................................................... 6
2.1 CONNECTINGTHEKEYPAD ........................................ 6
2.2 CONNECTINGKEYPAD ZONES.................................... 6
2.3 PROGRAMMABLEOUTPUT......................................... 7
3.0 Programming ................................................. 11
3.1 ENTERMODULEPROGRAMMINGMODE.................... 11
3.2 PROGRAMMINGMETHODS....................................... 12
3.2.1 Feature Select Programming ................................... 12
3.2.2 Decimal Programming .............................................. 12
3.3 MODULEBROADCAST............................................. 12
4.0 System Options .............................................. 14
4.1 PARTITIONASSIGNMENT.......................................... 14
4.2 DISPLAYCODEENTRY............................................ 14
4.3 DISPLAYEXITDELAYTIMER.................................... 14
4.4 DISPLAYENTRYDELAYTIMER................................ 15
4.5 CONFIDENTIALMODE.............................................. 15
4.6 MUTING.................................................................. 16
4.7 BEEP ONEXITDELAY.............................................. 17
4.8 CHIMEONZONECLOSURE...................................... 17
2 Installer’s Guide
4.9 BEEP ONTROUBLE.................................................. 17
4.10 KEYPAD TAMPERENABLE..................................... 18
5.0 Features For DGP-641 Only........................... 19
5.1 CONFIDENTIALMODETIMER.................................... 19
5.2 PGM STATE............................................................ 19
5.3 PGM ACTIVATIONEVENT........................................ 20
5.4 PGM DEACTIVATIONEVENT.................................... 20
5.5 PGM TIMEDMODE.................................................. 21
5.6 PGM TIMER............................................................ 21
5.7 PGM BASE TIME..................................................... 21
5.8 PGM OVERRIDE...................................................... 22
6.0 Features For DGP-641ACC Only................... 23
6.1 BUSVOLTMETER..................................................... 23
6.2 ASSIGNINGDOORSTOPARTITIONS.......................... 23
6.3 READER’SOPTIONS................................................. 24
6.3.1 Reader’s LED To Follow Partition’s Status ............ 24
6.3.2 Reader’s Beep To Follow Partition's Status........... 24
6.3.3 Reader's LED Options Upon Access Granted........ 25
6.4 DOORLOCK OPTIONS.............................................. 25
6.4.1 Unlock on REX (Request For Exit) .......................... 25
6.4.2 Door Unlocked Period .............................................. 25
6.4.3 Door Unlocked Period Extension ............................ 26
6.4.4 Relock Interval........................................................... 26
6.4.5 Door Unlocked Schedule.......................................... 26
6.4.6 Card Activates Door Unlocked Schedule ............... 27
Digiplex LCD Keypad 3n
6.5 DOORLEFT OPENOPTIONS.................................... 28
6.5.1 Door Left Open Access Alarm ................................. 28
6.5.2 Door Left Open Interval Before Access Alarm....... 29
6.5.3 Door Left Open Pre-Alarm........................................ 29
6.5.4 Door Left Open Pre-Alarm Timer ............................. 29
6.5.5 Door Left Open Alarm Feedback ............................. 30
6.5.6 Beep Timer For Door Left Open Alarm ................... 31
6.6 DOORFORCEDOPENOPTIONS............................... 31
6.6.1 Door Forced Open Access Alarm ............................ 31
6.6.2 Door Forced Open Feedback................................... 32
6.6.3 Beep Timer For Door Forced Open Alarm .............. 32
7.0 Message Programming .................................. 33
8.0 Glossary .......................................................... 36
4 Installer’s Guide
1.0 INTRODUCTION
Thank you for choosing Paradox®Security Systems. The Digiplex™
Security System is an advanced technology security system that will
provide reliable security protection and powerful features that are
easy to use. The elegant and user-friendly Digiplex™ LCD Keypad
will allow easy access to the security system's functions and
information at the touch of a button. Since all programming is
accomplished through the keypad, please read this manual carefully.
As well as normal security system functions, the Digiplex Access
Control Keypad (DGP-641ACC) can also be used for access
control. Access Control is designed to monitor and control the
access for up to 32 designated doors without the need of an
additional control panel. The events that occur on an Access
Control door can be logged in the control panel’s Event Buffer,
but can only be viewed through an Access Control Keypad.
Each door to become an Access Control door requires an
Access Control Keypad (DGP-641ACC), a reader (suggestion:
Posiprox CR-R880), a REX device (suggestion: Paradoor 460), a
door contact, and a locking device.
If desired, door contacts can also be assigned to zones in the
control panel to link the doors to the Digiplex Alarm system. This
will allow you to use the same door for the Access Control
system and the alarm system. Only two of the Access Control
features require that the Access Control door's door contact be
assigned to a zone: Burglar Alarm on Forced Door in section
[537] option [5] and Access to Armed Access Control Doors in
sections [802] to [896], fourth screen, option [8].
Digiplex LCD Keypad 5n
1.1 SPECIFICATIONS
Power input: 9-16 VDC, 80mA maximum
PGM current limit: 50 mA
Number of inputs: 1 (DGP-641)
2 (DGP-641ACC)
Power indication: Yellow LED on
Locate indication: Green and yellow LEDs flash simultaneously
Bus fault indication: Red and yellow LEDs flash alternately
Tamper Switch: Yes (also used to deactivate locate)
LCD: Super Twisted Nematic display (STN), wide
viewing angle, 2 lines of 16 characters, backlight
and contrast adjustable
Compatibility:
DGP-641: Any Digiplex Control Panel
DGP-641ACC: DGP-48 Control Panel for Access Control
V2.20ACC and higher
6 Installer’s Guide
2.0 INSTALLATION
2.1 CONNECTINGTHEKEYPAD
The Digiplex™ LCD keypads (DGP-641 and DGP-641ACC) are
connected to the control panel's bus in a star and/or daisy chain
configuration. This 4-wire communication bus provides power
and two-way communication between the control panel and all
modules connected to it. Connect the four terminals labeled red,
black, green and yellow of each keypad to the corresponding
terminals on the control panel (refer to Figure 1on page8).
Refer to the Digiplex Control Panel's Reference & Installation
Manual for the maximum allowable installation distance from the
control panel.
See Figure 4on page10 for connection drawings for the REX
device, reader, locking device and door contact to the desired
DGP-641ACC keypad. A typical installation is shown in Figure
2on page9.
The door contact follows the control panel’s EOL
definition. When EOL is enabled and the door contact is
not used, place a 1k
ΩΩ
resistor across the keypad’s Z1
and BLK input terminals. If EOL is not enabled, use a
jumper. If the REX device is not used, place a jumper
across the keypad’s Z2 and BLK input terminals.
2.2 CONNECTINGKEYPAD ZONES
Each keypad has one traditional hardwired input terminal,
allowing you to connect one detector or door contact directly to
Digiplex LCD Keypad 7n
the keypad. For example, a door contact located at the entry
point of an establishment can be wired directly to the input
terminal of the entry point keypad instead of wiring the door
contact all the way to the control panel.
Connect the device to the keypad's input terminal as shown in
Figure 1on page8. In order to communicate its status to the
control panel, devices connected to the keypad's input terminal
must be assigned to a zone in the control panel and the zone's
parameters must be defined. For more information on zone
assignment, please refer to the Digiplex Control Panel's
Reference & Installation Manual. Please note that even with the
ATZ (zone doubling) feature enabled, the keypad supports only
one detection device.
2.3 PROGRAMMABLEOUTPUT
Each keypad has one on-board PGM. A PGM is a programmable
output that toggles to its opposite state (i.e. a normally open
PGM will close) when a specific event has occurred in the
system (see section 5.0 on page19). Upon activation, the PGM
can provide 50mA to any device connected to it. If the current
drawn is to exceed the current limit, a relay should be connected
to the PGM as shown in Figure 1. With the DGP-641ACC
keypad, the PGM is reserved for the door lock (refer to Figure
4on page10).
8 Installer’s Guide
Figure 1: Connecting the Keypad and Keypad Zone
Autres manuels pour Digiplex DGP-641
2
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Paradox Clavier
Paradox
Paradox Spectra 1641 Manuel utilisateur
Paradox
Paradox Digiplex EVO DGP2-641BL Manuel utilisateur
Paradox
Paradox Spectra 1641BL Manuel utilisateur
Paradox
Paradox 1640 Manuel utilisateur
Paradox
Paradox Digiplex DGP-620 Manuel utilisateur
Paradox
Paradox K32+ Manuel utilisateur
Paradox
Paradox Esprit Manuel utilisateur
Paradox
Paradox Spectra 1689 Manuel utilisateur
Paradox
Paradox REM3 Manuel utilisateur
Paradox
Paradox TM50 Touch Manuel utilisateur
Paradox
Paradox Esprit 640 Manuel utilisateur
Paradox
Paradox Esprit 636 Manuel utilisateur
Paradox
Paradox SP5500 Manuel utilisateur
Paradox
Paradox Esprit 639 Manuel utilisateur
Paradox
Paradox IMPERIAL V32 Manuel utilisateur
Paradox
Paradox Esprit+ 642 Manuel utilisateur
Paradox
Paradox K32+ Manuel utilisateur
Paradox
Paradox K70C Manuel utilisateur
Paradox
Paradox Esprit 639 Manuel utilisateur
Paradox
Paradox Magellan MG32LRF Manuel de service
