Panduit MSPT-1.3 Manuel utilisateur

MSPT-1.3

PA26214A01

Rev. 01 18-Sep-09

TOOL SPECIFICATIONS.......................................................................................... 1

Safety ........................................................................................................................ 1

PRECAUTIONS AND GENERAL GUIDELINES ...................................................... 2

TOOL OPERATION .................................................................................................. 3

Bushings.................................................................................................................... 3

MAINTENANCE ........................................................................................................ 3

SPARE PARTS LISTING .......................................................................................... 5

Website: www.panduit.com

Email: [email protected]

Panduit Corp. • USA Headquarters • Tinley Park, IL

Tel: 888-506-5400, ext. 3255 • Fax: 630-759-7532

MSPT-1.3

MSPT-1.3: PA26214A01_01 Page: 1 of 5 18-Sep-09

The Panduit MSPT-1.3 Stud Punch tool punches a 34.1 mm (1-11/32") round hole

in 25 GA. min. to 20 GA max. mild steel studs.

TOOL SPECIFICATIONS

7.0 lbs. (3.2 kg)

NOTE: In the interest of higher quality and value, Panduit products are continually being

improved and updated. Consequently, pictures may vary from the enclosed product.

Safety

Safety is essential in the use and maintenance of Panduit tools and equipment. This manual and any

markings on the tool provide information for avoiding hazards and unsafe practices related to the use of

this tool. Observe all of the safety information provided.

MSPT-1.3

MSPT-1.3: PA26214A01_01 Page: 2 of 5 18-Sep-09

PRECAUTIONS AND GENERAL GUIDELINES

This symbol is used to call your attention to hazards or unsafe practices which could result in an

injury or property damage. The signal word, defined below, indicates the severity of the hazard.

The message after the signal word provides information for preventing or avoiding the hazard.

WARNING Hazards which, if not avoided, COULD result in severe injury or death.

CAUTION Hazards or unsafe practices which, if not avoided, MAY result in injury or

property damage.

WARNING

Read and understand all of the instructions and safety information in this manual

before operating or servicing this tool.

WARNING

Wear eye protection when operating or servicing this tool.

Failure to wear eye protection can result in serious eye injury from flying debris.

WARNING

Electric Shock Hazard:

This tool is not insulated. When using this unit on or near energized electrical lines,

use proper personal protective equipment.

CAUTION

Inspect the tool prior to use. Replace worn, damaged or missing components with replacement parts.

A damaged or improperly assembled tool may break. Use this tool for manufacturer’s intended use

only. Use other than that which is described in this manual may result in injury or damage to the tool.

CAUTION

Do not add extensions (cheaters) to the handles. Using excessive force may result in injury or

damage to the tool. If excessive force is required to complete a punch, verify that the type and

thickness of material do not exceed the capacity of the tool.

IMPORTANT INFORMATION

Do not use on heavier than 20 gauge mild steel.

MSPT-1.3

MSPT-1.3: PA26214A01_01 Page: 3 of 5 18-Sep-09

TOOL OPERATION

Position the punch on the metal stud. Squeeze the handles together. The slug will fall free when the

hole is complete.

Bushings

Bushings are available for the holes punched by the MSPT-1.3 tool. Bushings protect wire insulation

from the sharp edges of the metal stud. Complies with NEC Article 300-4(b)(1).

Fig. A

Panduit Part No. Description Qty.

MSG-1.3-C

Metal Stud Grommet

for 1-11/32” hole

(see Fig. A)

100 pc. Pack

MSG-1.3-M 1,000 pc. Pack

Fig. B

MSGV-1.3-C Metal Stud Grommet

for 1-11/32” hole

(Anti-vibration; for

½” to 1” pipe)

(see Fig. B)

100 pc. Pack

MSGV-1.3-M 1,000 pc. Pack

MAINTENANCE

Lubricate all moving parts with light weight oil.

To replace the punch, refer to the illustration on the next page, and follow this procedure:

1. Remove the locknut (A) from the pivot bolt (B),

and then remove the pivot bolt from the punch holder (8).

2. Remove the entire punch holder shaft and sleeve from the C-frame.

3. Depress the sleeve and unscrew the punch from the punch holder.

MSPT-1.3

MSPT-1.3: PA26214A01_01 Page: 4 of 5 18-Sep-09

MSPT-1.3 ILLUSTRATION

NOTE: All parts shown for

reference only.

Consult factory for lead time and

part availability.

MSPT-1.3

MSPT-1.3: PA26214A01_01 Page: 5 of 5 18-Sep-09

MSPT-1.3 STUD PUNCH SPARE PARTS LISTING

KEY PART # DESCRIPTION QUANTITY

50212850 Stud punch complete

1 52027489 Lever unit 1

2 Link (see below for service parts) 1

4 Locknuts 3

5 50213032 Washer, flat .968 x 1.62 x .062 1

6 50215574 Spring, compression 1

9 90513614 Retaining ring, .865; Truarc #5100-93-S-PP 1

12 50248235 Punch, conduit 1

13 50212974 Die 1

14 52027490 Handle, green 1

15 C-Frame unit 1

17 90507649 Screw, set, 1/4–20 x .375 socket w/locking patch 1

18 90506170 Screw, set, 1/4–20 x .250 socket w/locking patch 1

20 Bolts, pivot, 1/4 x 20 3

25 50213016 Bushing 1

MSPT-1.3 STUD PUNCH REPAIR KITS LISTING

50060155 Pin kit (includes items 4 and 20)

50059327 Link kit (includes items 2, 4 and 20)

** 52026022 Sliding mechanism service kit (includes items 7 and 8)

** Use one flat washer (50213032), as shown in the illustration, when replacing the punch holders.

For ordering parts, call 1-888-506-5400, ext. 3226.

Table des matières

Autres manuels Panduit Outils de sertissage

Panduit

Panduit BlackFin CT-2920 Manuel utilisateur

Panduit

Panduit CT-1000 Manuel utilisateur

Panduit

Panduit BlackFin CT-2300 Series Manuel utilisateur

Panduit

Panduit CT-930LPCH Manuel utilisateur

Panduit

Panduit ClackFin CT-3001/CCPBT Manuel utilisateur

Panduit

Panduit Contour Crimp CT-1015 Manuel utilisateur

Panduit

Panduit CT-3001 Manuel utilisateur

Panduit

Panduit CTFP-25 Manuel utilisateur

Panduit

Panduit CT-1003 Mode d’emploi

Panduit

Panduit Blackfin CT-2980/TO Manuel utilisateur

Panduit

Panduit CT-1104 Mode d’emploi

Panduit

Panduit BlackFin CT-2980/ST Manuel utilisateur

Panduit

Panduit CT-2002CH Manuel utilisateur

Panduit

Panduit CT-1123 Mode d’emploi

Panduit

Panduit CT-2940/L Manuel utilisateur

Panduit

Panduit BlackFin CT-2600/L Manuel utilisateur

Panduit

Panduit CT-2500 Manuel utilisateur

Panduit

Panduit BlackFin CT-2980/STBT Manuel utilisateur

Panduit

Panduit BlackFin CT-3980/BT Manuel utilisateur

Panduit

Panduit CT-1000 Guide de l'administrateur

Panduit

Panduit Black Fin CT-2931 Series Manuel utilisateur

Panduit

Panduit Black Fin CT-2931/STCVUK Manuel utilisateur

Panduit

Panduit PAT4.0 Series Manuel utilisateur

Panduit

Panduit BlackFin CT-2600/LBT Manuel utilisateur

Manuels Outils de sertissage populaires d'autres marques

JST

JST CS 10 Manuel utilisateur

molex

molex 63811-5100 Manuel utilisateur

Danfoss

Danfoss ET4200 Manuel utilisateur

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manuel utilisateur

TE Connectivity

TE Connectivity 2063528-1 Manuel utilisateur

molex

molex 63825-3000 Manuel utilisateur

Tyco Electronics

Tyco Electronics 69156-1 Manuel utilisateur

CRH

CRH CRL CBLHCT1 Manuel utilisateur

Emerson

Emerson Klauke ES 105CFM Manuel utilisateur

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Mode d’emploi

Danfoss

Danfoss ET4350 Manuel utilisateur

Milwaukee

Milwaukee M18 Manuel utilisateur

HOGERT

HOGERT HT1P169 Manuel utilisateur

Textron

Textron ESG105L Manuel utilisateur

Tyco Electronics

Tyco Electronics 90035-3 Manuel utilisateur

Emerson

Emerson Klauke ES 20RMCCFB Manuel utilisateur

Continental Refrigerator

Continental Refrigerator PC150HD Manuel utilisateur

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Manuel utilisateur