Panasonic AW-HS50 Series Manuel utilisateur

★This is to explain AW-HS50 switcher’s basic setup and how to deal with problems (e.g. no image output) when they

occur.

■Display of Menu Screen (OSD: On-Screen Display)

The menu screen is displayed by holding down OSD ON button –(Figure 1). It is superimposed on the image output

from SDI OUT 2 connector and DVI OUT connector.

(To clear the menu, hold down OSD ON button again.) * The menu screen is not output from SDI OUT 1 connector.

Turn OSD dial to select the setting, and press the dial to enter the selection. The setting value can be varied by turning

the dial while the value is blinking.

■Settings for Crosspoint

A source is selected by pressing one of A bus or B bus crosspoint buttons. It is the signal which has been set in

advance using the menu, and called up as the source.

Assignment to the crosspoint buttons is carried out using the menu: [9] XPT SW Assign Menu –(Figure 2).

By factory default, pressing the crosspoint button 1 will make the unit call up the source input into “SDI-IN1”.

If XPT6 –XPT10 need to be called up, press the crosspoint buttons while SHIFT button is held down.

AW-HS50 –Basic Operations & Troubleshooting

(Figure 1: AW-HS50 Control Panel)

(Figure 2: Menu Screen for [9] XPT SW Assign Menu *factory default)

A bus crosspoint buttons

OSD ON button

SHIFT button

B bus crosspoint buttons

OSD dial

BUS DELEGATION buttons

FTB ON button

To crosspoint buttons 1 –10, external video input signals, internally generated signals, etc. can be assigned as a

source.

■Settings for Output

This switcher can output signals from the three connectors: SDI OUT1, SDI OUT2 and DVI-D OUT.

The output signals are set on the menu: [11] Output Menu –(Figure 3).

The output systems can individually be assigned the following signals.

※For MV (Multi View Display), please see the following manual “AW-HS50 –Multi View Display”.

https://eww.pass.panasonic.co.jp/pro-av/support/content/faq/EN/remcam/17_.pdf

★Need help? Troubleshooting ★

■“No image output”

・Does the signal format of the switcher match that of the input source?

If AW-HS50 switcher receives an input signal that is different from its system format, a black screen or distorted

image is displayed.

Please check if the switcher’s system format (see below for the menu) matches that of the input source.

※AW-HS50 Menu ：[14]SYSTEM Menu ＞1．Format

(Supported formats: 1080/59.94i, 1080/50i, 720/59.94p, 720/50i, 1080/24PsF, 1080/23.98PsF, 480/59.94i, 576/50i)

※Video signals will not be switched even if a button is pressed where “NoAssign” is assigned.

(Figure 3: Menu Screen for [11] Output Menu *factory default)

Crosspoint Button Source Name Source

SDI-IN1 to SDI‐IN4 Images inputted into SDI-IN1 to 4

DVI-IN Image inputted into DVI-IN

FMEM1, FMEM2 Images stored in the switcher

CBGD Signal outputted from the switcher's built-in color generator

CBAR Switcher's internal color-bar signal

Black Switcher's internally generated signal (black signal)

NoAsign No signal assigned

1 to 10

PGM

This is the main line output.

Images with wipe, mix, key, PinP or other effects added are outputted.

PVW

PVW images which enable the next operation to be checked are outputted.

CLN

Clean signals (images resulting when the key and PinP effects have been

removed from the PGM signal) are outputted.

AUX

The signal selected using the AUX bus is outputted.

MV Multi view display signal is outputted.

KEY OUT Key signal is outputted.

・If DVI input is being used as a source, does the output signal have the resolution supported by

AW-HS50 switcher?

When a signal is input with unsupported resolution, the switcher cannot take it in correctly. A black screen or

distorted image may be displayed.

※For DVI input, please see the following manual “AW-HS50 –DVI Input & Output”.

https://eww.pass.panasonic.co.jp/pro-av/support/content/faq/EN/remcam/24_.pdf

Example: DVI input does not support “1080/59.94i”.

・The input signal is coming via a converter.

If the output signal from the source is being converted (HDMI⇒SDI, HDMI⇒DVI), please check if the format and

resolution of the output signal from the converter are supported byAW-HS50 switcher.

About the converter itself, please contact the manufacturer of your equipment.

・Is a copyright-protected device being used for an input source?

This switcher does not support HDCP. If a copyright-protected DVD player or PC is used as a source, the output

image is a black screen or distorted.

・Is FTB (fade to black) ON button –(Figure 1) lit?

When this button is lit, the screen is black after the program image has faded out.

Press FTB ON button to check if an image fades in to be displayed on the screen.

■“The image won’t be switched by pressing crosspoint buttons.”

・Is any of BUS DELEGATION buttons –(Figure 1) blinking?

These 3 buttons are used for selection at the time of setting the AUX bus, PinP source and key source/key fill.

When all of them are off, the switcher can select an input source for the background.

If one button is blinking, press it to turn it off. Then check if the image will be switched.

※For “BUS DELEGATION” features, please see the following manuals.

☆[AUX] button: Manual “AW-HS50 –AUX Bus”

https://eww.pass.panasonic.co.jp/pro-av/support/content/faq/EN/remcam/16_.pdf

☆[PinP] button: Manual “AW-HS50 –Combining PinP”

https://eww.pass.panasonic.co.jp/pro-av/support/content/faq/EN/remcam/15_.pdf

☆[KEY-F/S] button: Manual “AW-HS50 –Combining Telop”

https://eww.pass.panasonic.co.jp/pro-av/support/content/faq/EN/remcam/13_.pdf

: Manual “AW-HS50 –Chroma Keying”

https://eww.pass.panasonic.co.jp/pro-av/support/content/faq/EN/remcam/14_.pdf

■“The settings return to the default values by themselves after turning the power on.”

On the rear panel, is “BOOT” switch at [SV] side? If this switch is at [SV] side, the switcher boots up with its factory

default settings when you boot it up. Normally, please have it at [NM] side when using the switcher.

■Other Features

※Regarding the operations and setting procedures of major AW-HS50 features, illustrated manuals are

available at our website.

☆Frame Memory (FMEM): “AW-HS50 –Storing Still Images in FMEM”

(AUX version) https://eww.pass.panasonic.co.jp/pro-av/support/content/faq/EN/remcam/11_.pdf

(Software version) https://eww.pass.panasonic.co.jp/pro-av/support/content/faq/EN/remcam/12_.pdf

☆Setting for Linking AW-RP50: “AW-HS50 –Setting for LinkingAW-RP50”

https://eww.pass.panasonic.co.jp/pro-av/support/content/faq/EN/remcam/18_.pdf

☆Audio (Passing Through) Setting: “AW-HE40 & AW-HS50 –Audio (Passing Through) Settings”

https://eww.pass.panasonic.co.jp/pro-av/support/content/faq/EN/remcam/23_.pdf

Autres manuels pour AW-HS50 Series

Table des matières

Autres manuels Panasonic Changer

Panasonic

Panasonic PN28080K-ID Manuel utilisateur

Panasonic

Panasonic Switch-M24eG PN28240K-TH Manuel utilisateur

Panasonic

Panasonic KX-T206E Manuel utilisateur

Panasonic

Panasonic AW-HS50 Series Manuel utilisateur

Panasonic

Panasonic FP (ABP8) Manuel utilisateur

Panasonic

Panasonic PN28080i Manuel utilisateur

Panasonic

Panasonic AW-HS50E Manuel utilisateur

Panasonic

Panasonic Micro SD KX-HN6032AZW Manuel utilisateur

Panasonic

Panasonic Switch-M8eGi Series Manuel utilisateur

Panasonic

Panasonic AV-HS6000 Manuel utilisateur

Panasonic

Panasonic AV-HS450N Manuel utilisateur

Panasonic

Panasonic ZEQUO 2200 Manuel utilisateur

Panasonic

Panasonic KX-HNB600E Manuel utilisateur

Panasonic

Panasonic KX-HNS103 Manuel utilisateur

Panasonic

Panasonic AK-HC1500 Manuel utilisateur

Panasonic

Panasonic KX-HNB600 Manuel utilisateur

Panasonic

Panasonic AW-HS50N Manuel utilisateur

Panasonic

Panasonic S24GPWR Manuel utilisateur

Panasonic

Panasonic AV3205G3 Manuel utilisateur

Panasonic

Panasonic ABV 1 Series Manuel utilisateur

Panasonic

Panasonic AV-HS04M1 Manuel utilisateur

Panasonic

Panasonic AW-SW300 Manuel utilisateur

Panasonic

Panasonic WJSQ308 - SEQUENTIAL SWITCHER Manuel utilisateur

Panasonic

Panasonic CF-VEB Series Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur