Panasonic WJHDE300 - DIGITAL DISK RECORDER Manuel utilisateur

Extension Unit

Instructions

Model No. WJ-HDE300

WJ-HDE

300

Extension Unit

Before attempting to connect or operate this product,

please read these instructions carefully and save this manual for future use.

The serial number of this product may be found on the rear

of the unit.

You should note the serial number of this unit in the space

provided and retain this book as a permanent record of your

purchase to aid identification in the event of theft.

Model No. WJ-HDE300

Serial No.

The lightning flash with arrowhead sym-

bol, within an equilateral triangle, is

intended to alert the user to the pres-

ence of uninsulated "dangerous voltage"

within the product's enclosure that may

be of sufficient magnitude to constitute a

risk of electric shock to persons.

The exclamation point within an equilat-

eral triangle is intended to alert the user

to the presence of important operating

and maintenance (servicing) instructions

in the literature accompanying the appli-

ance.

Power disconnection. Unit with or without

ON-OFF switches have power supplied to

the unit whenever the power cord is insert-

ed into the power source; however, the unit

is operational only when the ON-OFF

switch is in the ON position. The power

cord is the main power disconnect for all

units.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

SA 1965

SA 1966

NOTE: This equipment has been tested and found to com-

ply with the limits for a Class A digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to pro-

vide reasonable protection against harmful interference

when the equipment is operated in a commercial environ-

ment. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful

interference to radio communications.

Operation of this equipment in a residential area is likely to

cause harmful interference in which case the user will be

required to correct the interference at his own expense.

FCC Caution: To assure continued compliance, (example -

use only shielded interface cables when connecting to com-

puter or peripheral devices). Any changes or modifications

not expressly approved by the party responsible for compli-

ance could void the user’s authority to operate this equip-

ment.

For U.S.A.

WARNING:

• To prevent fire or electric shock hazard, do not expose this appliance to

rain or moisture. The apparatus shall not be exposed to dripping or

splashing and that no objects filled with liquids, such as vases, shall be

placed on the apparatus.

• All work related to the installation of this product should be made by

qualified service personnel or system installers.

CAUTION:

•Read the label on the rear of the unit for identification of this product,

and the power ratings.

This Class A digital apparatus complies with canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme

NMB-003 du Canada.

For Canada

■Important Safety Instructions

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

8) Do not use near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that

produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider

than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are

provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the

obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles and the points

where they exit from the apparatus.

11) Only use attachments/accessories specified by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a

cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-overs.

13) Unplug this apparatus during lightning storms or when unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has been spilled or objects fallen into the apparatus, the apparatus

has been exposed to rain or moisture, does not operate normally, or has been dropped.

S3125A

Contents

■Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

■General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

■Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

■Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

●Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

●Rear View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

●Inside the Front Lid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

■Replacing/Mounting HDDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

●Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

■Mounting in a Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

●Unit Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

●How to Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

■Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

●Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

■Setup Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

●Basic Setups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

●Changing Setups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

●Recovery of RAID5 Disk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

●Unit Number Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

■Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

■Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

■Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

■Precautions

•Do not operate the appliance beyond its specified tem-

perature, humidity or power source ratings.

Do not use the appliance in an extreme environment

where a high temperature or high humidity exists. Use

the appliance at temperatures within +5 °C to +45 °C

(41 °F to 113 °F) and humidity below 85 %.

The input power source for this appliance is 120 V AC

60 Hz.

•Avoid shock and vibration

Shock or vibration may damage the HDD.

The HDDs are fragile especially when the HDD motors

are revolving and the HDD POWER indicator lights. Be

sure to turn off either switch: the POWER switch on the

rear panel, or the HDD POWER switch inside the front

lid: before you mount the unit into a rack or dismount it.

Do not move the HDD for 30 seconds after turning off

the power.

•Pay attention to static electricity

Put your hand on a metallic surface to discharge static

electricity before installation.

Do not touch components mounted on the HDD directly

with your hand.

Hold only the two sides of the HDD when installing.

■General

The extension unit WJ-HDE300 can accommodate up to four hard disk drives per unit to add available disk space to the digital

disk recorder WJ-HD316A/WJ-HD309A series. Up to seven extension units can be connected to a digital disk recorder. The

units can be operated in RAID level 5* mode for high tolerance to disk error.

*RAID level 5 (Redundant Arrays for Independent Disks, independent data disks with distributed parity blocks)

RAID level 5 regards 3 or more drives as one drive, and it is possible to read data by automatically attaching error correc-

tion data even though one of the drives is broken. (It is impossible to read data if 2 or more drives are broken.)

RAID level 5 requires a minimum of 3 drives per unit.

When using the RAID function, the logical disk size of the extension unit will be as below.

Logical disk size = Smallest size of the disk among the disks in the extension unit x (Number of the disks in the extension

unit - 1) The actual space may be several percent lower than the logical space.

*Important

When set to RAID level 5, the digital disk recorder will not access the HDD preinstalled in it, but will access only the HDDs

in the extension unit.

•Avoid condensation on the surface of the HDD.

If this happens, do not turn on the power of the appli-

ance and leave the appliance for around 2 hours.

Wait until the dew evaporates in any of the following

cases.

•The appliance is moved to a place significantly dif-

ferent in temperature or humidity.

•The appliance is moved out from an air-conditioned

room.

•The appliance is placed in an extremely humid

place.

•The appliance is placed in a room where a heater

has just been turned on.

•Consumable parts

Contact your dealer about replacement when the time

comes.

A hard disk drive needs replacing after a certain length

(depends on the model) of operation.

Cooling fans also need replacing after around

20 000 - 30 000 hours of operation.

•Do not block the ventilation opening or slots on the

cover.

To prevent the appliance from overheating, place it at

least 5 cm (2 inches) away from the wall.

•Avoid placing the unit on an inclined surface.

Otherwise, malfunction or damage to the disk may

occur. Place the unit in a horizontal position.

■Appearance

●Front View

qError indicator [ERROR]

Lights when an error occurs. Refer to Troubleshooting

for details.

Red: System error

Orange: Thermal error or malfunction of the cooling fan.

wHDD power indicator [HDD POWER]

ON: Indicates that the HDDs are powered.

OFF: Indicates that the HDDs are not powered.

Notes:

•Do not move or shock the unit while this indicator is

lit. Otherwise, the HDDs will be damaged.

•This indicator will light and go out by the setting of

the HDD POWER switch inside the front lid of the

unit, or by the operation on the HDD SAFETY MENU

of the digital disk recorder.

eOperate indicator [OPERATE]

Lights green when turning on the power switch on the

rear panel.

rHDD access indicators [HDD 1] [HDD 2] [HDD 3]

[HDD 4]

Each indicator lights to indicate the status of the

respective HDD.

Green: Indicates that the respective HDD is running

normally.

Red: Indicates that the respective HDD is the first faulty

drive among the HDDs in the unit.

Red blink: Indicates that the respective HDD is the

second or subsequent faulty drive among the HDDs

in the unit.

Orange-red alternate blink/Orange: Indicates that the

respective drive is currently being recovered in

RAID level 5 mode.

These indicators normally show the status of the

respective drive, but they work as a set when a system

error occurs. Refer to Troubleshooting for further infor-

mation.

Important

When one of the indicators lights red, replace the

respective HDD immediately. If two or more indicators

light/blink red, it will be impossible to recover data.

There may be cases where it is eventually impossible to

recover data if two drives are coincidentally damaged

or the second drive fails during the data recovery

process.

tFront cover

Detach the front cover when it is necessary to install

HDDs or to operate the switches inside the unit.

ERROR

HDD 1 HDD 2 HDD 3 HDD 4

HDD

POWER

OPERATE

Extension Unit

WJ-HDE

qwe r t

POWER

AC IN

SIGNAL GND

IN OUT

EXT

yu i io

●Rear View

ySerial in connector [IN]

Connect the WJ-HD300 series digital disk recorder or

other extension unit with the supplied serial cable.

uSerial out connector [OUT1] [OUT2]

Connect another extension unit with the supplied serial

cable.

iCooling fan

oSignal GND terminal [SIGNAL GND]

Connect this terminal if required, to the SIGNAL GND

terminal of other equipment to avoid a possible ground-

ing loop and noise.

!0 Power switch [POWER]

Turn on the power of the unit with this switch before

turning on the power of the digital disk recorder, or turn

them on simultaneously. Otherwise, the HDDs will not

be mounted.

When turning off the power of the unit with this switch,

turn off the power of the digital disk recorder first, and

then turn off the power of this unit after confirming that

all HDD access indicators are not lit or blinking.

!1 AC inlet [AC IN]

Connect the supplied power cord.

!2 Cable clamp

SINGLE RAID5

MODE

RESET

HDD POWER

RECOVER

OFF ON

w’

e’

q’

● Inside the Front Lid

q'Error indicators

Functions the same as on the front panel.

Red: System error

Orange: Thermal error or malfunction of the cooling fan.

w'HDD power indicator

Functions the same as on the front panel.

ON: Indicates that HDDs are powered.

OFF: Indicates that the HDDs are not powered.

e'Operate indicator

Functions the same as on the front panel.

Lights green when turning on the power switch on the

rear panel.

!3 Reset button [RESET]

This button is located inside the unit. To access this

button, it is necessary to detach the front cover. Press

this button using a small screw driver (not supplied).

•When SINGLE is selected

After adding or replacing any of the HDDs, press this

button only. Refer to Setup Procedures for details.

•When RAID 5 is selected

This button is used in combination with the RECOVER

button and MODE switch after adding or replacing any

of the HDDs. Refer to Setup Procedures for details.

Important

Do not press the RESET button and the RECOVER

button simultaneously when SINGLE is selected.

Otherwise, the setting of the digital disk recorder

may be initialized and it may cause a malfunction.

!4 Mode switch [MODE]

RAID 5: Applies RAID level 5 mode (striping at the byte

level also stripe error correction information).

SINGLE: Applies SINGLE mode (no striping across dri-

ves for data or error correction information). Default

position

Important

•Changing the MODE switch will not be accepted when

the ERROR indicator lights red and/or when HDD 1-4

indicate a system error status by lighting red and

orange. When this happens, ask your dealer to solve

the error.

•When set to RAID5, the HDD preinstalled in the digital

disk recorder will not work. Instead, it is applied only to

the HDDs installed in the extension unit and the digital

disk recorder will perform storage and readout of the

image data by accessing the extension unit.

•The MODE switches of all extension units in a system

should be set to the same position, SINGLE or RAID5.

Otherwise, the system will malfunction.

•The available disk space of the unit can be logically

calculated as follows. The actual space may be several

percent lower than you calculated depending on the

HDD type used and their combination. The most effi-

cient way is to use the same type drives.

When SINGLE is selected, it will be the sum of all

the HDD sizes.

When RAID 5 is selected, it will be as follows.

When 3 HDDs are in the unit: It will be double the

size of the smallest HDD size.

When 4 HDDs are in the unit: It will be triple the size

of the smallest HDD size.

For example, if 4 HDDs of 80 GB, 120 GB, and two

160 GB are mounted, the available disk space will

be 80 G x 3 = 240 GB.

!5 HDD power switch [HDD POWER]

Use this switch in the ON position for normal operation.

ON: Supplies the power to the HDDs and the HDD

power indicators will light. Default position

OFF: Does not supply the power and the HDD power

indicators will go out.

!6 Recover button [RECOVER]

Use this button with the RESET button after replacing

the HDDs used in the RAID 5 mode to start data recov-

ery.

Refer to page 12 for details.

■Replacing/Mounting HDDs

Up to four HDDs (locally procured) can be installed in an

extension unit.

Important

•Type of hard disk drive

Consult your dealer about hard disk drives. Use only

hard disk drives compatible with the extension unit. If

unauthorized hard disk drives are used, it may cause a

system error.

It is recommended that the same type drives having the

same capacity should be installed in the extension units

to maximize the usable capacity.

•The HDDs should be installed in the proper positions in

the order as shown above. Do not skip or reverse the

order of the HDD positions. Otherwise, the recorder will

not recognize the extension unit or wrongly mounted

drives.

•The MODE switches of all units in a system should be

set to the same position, SINGLE or RAID5. When

mixed, it will cause a system error. See Troubleshooting

for details.

•When applying the RAID5 mode, it requires a minimum

of 3 drives per unit. When only two drives are mounted

in position #1 and #2, the ERROR indicator will be lit

red, HDD3 indicator will be lit red, and HDD4 indicator

will blink red.

•When applying the RAID5 mode, the digital disk

recorder will not access the HDD preinstalled in it, but

will access only the HDDs in the extension unit.

•Do not change the installed positions after the system

has been operated. Otherwise, data readout will not be

performed

•The replaced/added HDDs will be formatted.

SINGLE mode: Only the replaced/added HDD will be

formatted. For example, when the HDD

4 of the extension unit 2 is replaced,

only the HDD4 of the extension unit 2

will be formatted.

RAID 5 mode: All the HDDs of the extension units will

be formatted when a new HDD is

added or a preinstalled HDD is

removed. For example, when the HDD

4 of the extension unit 2 is added, all

the HDDs of the extension unit 2 will be

formatted.

●Procedures

1. HDD power-off procedures

Perform either of the following procedures depending

on the installation situations to stop the HDD motors.

Case 1: When the rear of the units is accessible, turn off

the power switches of the digital disk recorder

first, and turn off extension units.

Case 2: When the rear of the units is inaccessible, for

example when mounted in a rack, open the

SETUP MENU of the digital disk recorder and set

the HDD SAFETY MODE to ON. The extension

units will turn to the HDD power-off mode.

Refer to Setup Procedures of this manual and the

Operating Instructions included with the digital

disk recorder for details .

2. Detach the front cover and the front panel.

2-1 Remove the two screws.

HDD 2

HDD 1

HDD 4

HDD 3

POWER

2 - 1

2-2 Slide the front cover to the left.

2-3 Pull the front cover toward you.

2-4 Disconnect the harness.

2-5 Remove the six screws (marked with ∆) and detach

the thin metal plate covering the front side.

2-6 Disconnect the cables when adding or replacing

the HDD.

3. Remove two of the HDD mounting brackets.

•Remove the four screws and pull the brackets toward

you.

•When replacing an HDD, remove it from the bracket.

4. Prepare the HDDs to be fixed on the brackets.

•Release the static electricity from your body before

touching the HDDs.

•Put the conductive bag (in which the HDD was packed)

on a soft surface and place the HDD on it with the cir-

cuit board side down.

5. Fix the HDDs on the brackets.

5-1 Slide the HDD onto the bracket.

5-2 Tighten the four screws (supplied) to fix the HDD on

the bracket.

5-3 Repeat above steps to fix all the HDDs on the

bracket.

Do not use an electric screwdriver to fix them.

Recommended tightening torque = 0.49 N · m

{5 kgf·cm}

6. Set all the HDDs as master using the jumper connector.

Note: This setting is subject to change without notice.

Refer to the diagram attached on the HDD or the

operating instructions of the HDD for the jumper

connector assignment.

2 - 4

2 -5

2 - 6

2 - 2

2 - 3

Autres manuels pour WJHDE300 - DIGITAL DISK RECORDER

Table des matières

Autres manuels Panasonic Stockage

Panasonic

Panasonic RP-SDB32GB1K Manuel utilisateur

Panasonic

Panasonic RP-SDU32GU1K Manuel utilisateur

Panasonic

Panasonic JU-455-5 Manuel utilisateur

Panasonic

Panasonic LKM-F931-1 Manuel utilisateur

Panasonic

Panasonic RP-SDUB64GAK Manuel utilisateur

Panasonic

Panasonic RP-SDQ32GE1K Manuel utilisateur

Panasonic

Panasonic CF-VFS251W Manuel utilisateur

Panasonic

Panasonic RP-SDUT64GAK Manuel utilisateur

Panasonic

Panasonic Carte miniSD Manuel utilisateur

Panasonic

Panasonic RP-SDU64GE1K Manuel utilisateur

Panasonic

Panasonic RP-SDP24GE1K Manuel utilisateur

Panasonic

Panasonic AJ-P2C064AG Manuel utilisateur

Panasonic

Panasonic AG-MSU10 Manuel utilisateur

Panasonic

Panasonic SV-PT1EB Manuel utilisateur

Panasonic

Panasonic SD Memory Card Manuel utilisateur

Panasonic

Panasonic JU-475-4 Manuel utilisateur

Panasonic

Panasonic AJ-PX800G Manuel utilisateur

Panasonic

Panasonic JU-314 Manuel utilisateur

Panasonic

Panasonic RP-SMGA32GAK Manuel utilisateur

Panasonic

Panasonic CFVFS272W - SUPERDISK DRIVE FOR P.COM Manuel utilisateur

Panasonic

Panasonic CF-VFS271 Manuel utilisateur

Panasonic

Panasonic CF-VHD Series Manuel utilisateur

Panasonic

Panasonic RP-SDUC32GAK Manuel utilisateur

Panasonic

Panasonic RP-SM16GFE1K Manuel utilisateur

Manuels Stockage populaires d'autres marques

QNAP

QNAP TS 32PXU Series Manuel utilisateur

LaCie

LaCie RUGGED RAID Manuel utilisateur

Freecom

Freecom CLS DOCK Manuel utilisateur

PNY

PNY Attache P-FD64MBATT3 Manuel utilisateur

HP StorageWorks MSL2024 Manuel utilisateur

OLT

OLT 6x6 Maximizer Manuel utilisateur

Transcend

Transcend JetFlash 160 Manuel utilisateur

LaCie

LaCie RUGGED MINI Manuel utilisateur

Thunderbolt

Thunderbolt 600 Manuel utilisateur

Intel

Intel RAID High Availability Manuel utilisateur

LaCie

LaCie 12big Thunderbolt 3 Manuel utilisateur

Spectra Logic

Spectra Logic T-Series Spectra T50e Manuel utilisateur

Tabernus

Tabernus Enterprise Erase E2400 Manuel utilisateur

Rocstor

Rocstor COMMANDER 3F series Manuel utilisateur

HP P9000 Manuel utilisateur

Western Digital

Western Digital Ultrastar Data60 Manuel utilisateur

Dell

Dell PowerVault MD3600f Series Manuel utilisateur

CFI

CFI TERA STOR SATA RAID IV Manuel utilisateur