Panasonic BL-C111A - Network Camera - Pan Guide de démarrage rapide

HomeLogic LLC ●

100 Hoods Lane

●

Marblehead, MA 09145

●

Phone (781) 639-5155

●

Fax (781) 639-9677

OneHome™

Management and Control Solutions

Camera Integration Note

Manufacturer: Panasonic

Model Number(s): BL-C111A, BL-C131A (wireless)

Comments: Network Camera (version 3.10)

Document Revision Date: 5/19/2011

NOTE: This document refers to Camera setup in software versions below 5.2 ONLY.

Please see the Rev 5.2 Integration Note for systems running 5.2 or greater.

VERVIEW AND SUPPORTED FEATURES

Installing the Panasonic camera can be broken down into the following steps:

1. Install cameras at desired locations, and pull power and Cat5 cabling as needed. Refer to the

Panasonic documentation for mounting details.

2. Connect the cameras electrically to the home network and configure the cameras. See Camera

Configuration.

3. Integrate the cameras into the OneHome system and test proper operation. This step is outlined

in HomeLogic Configuration Details.

BL-C111A

AND

BL-C131A

SUPPORT THE FOLLOWING FEATURES

Pan / Tilt: These cameras can be turned to see various locations.

Presets: These cameras support presets, allowing the user to store predefined locations such as a

driveway or pool. This feature requires OneHome software version 4.0 or later.

Image Flip: These cameras can be mounted with its base up or down, and the image will appear normal.

Built-in Audio: Audio from the Panasonic cameras built-in microphone is supported in version 4.0 and

later.

Motion Detection: These cameras support motion detection to trigger events in the OneHome system.

BL-C111A

AND

BL-C131A

NOT

SUPPORT THE FOLLOWING FEATURES

Zoom: Cameras lacking optical zoom cannot be zoomed in HomeLogic.

AMERA

ONFIGURATION

The camera configuration is done with software provided by Panasonic, which must be run from a

computer with Windows also connected to the same network as the camera.

The software program from Panasonic is EasyConfig.exe: the version we checked is shown at the top.

MPORTANT

OTES

1. Cameras must be configured one at a time: If you are installing more than one camera, setup

the first one completely before powering up subsequent cameras.

2. Setup the camera within 20 minutes: Initial settings must be made within 20 minutes of the

camera being turned on. If the camera has been powered up for more than 20 minutes, cycle

power to the camera before proceeding.

2 of 11

3. DON’T LOSE THE CAMERA PASSWORD: During setup you will create a user name and

password, which are required to make any other changes in the future. If you lose the user name

or password you will have to factory reset the camera and repeat this entire procedure.

4. DEFAULT USER NAME / PASSWORD: For Panasonic cameras, our default user name is

Administrator and our default password is password.

3 of 11

TARTING THE

ANASONIC

AMERA

OFTWARE

1. Insert the CD from the camera into your PC: It should autostart the Network Camera Setup

software. If it does not, launch Setup.exe from the Panasonic CD.

2. The following Screen appears. Choose Search for Cameras.

3. Wait a moment to allow the software to find the camera: the following screen appears.

4 of 11

4. Select the desired camera, and then click the Access Camera button. After a short delay you will

see a new browser window with the initial password screen below:

5. Type in your desired user name and password and click Save. By default we set the user name to

Administrator and the password to password.

6. After a moment initial setup will complete. When prompted with the screen below, click the “To

Single Camera page” button.

7. You will be prompted to enter your user name and password to login, as shown in the image

below. Type in the user name and password you just set, and click OK.

5 of 11

AMERA

ETTINGS

1. After typing in your user name and password, you will be shown the standard browser interface to

the camera.

2. The system will attempt to install an ActiveX control to show the camera image in the browser

window. This control is not needed for proper OneHome operation, but is needed if you wish to

see the camera image on that computer. If any dialogs appear, close them or accept the ActiveX

control as appropriate for your situation.

3. On Windows computers with popup blocking enabled, you will need to click the appropriate bar to

enable the installation of the ActiveX control.

4. Click Setup at the top to bring up the screen shown below:

6 of 11

5. Click UPnP on the left, then click Disable in the both parts of the screen, as shown below. Click

Save to store your settings.

6. Under Accounts to the left, click Administrator to bring up the screen below. Click Permit

access from guest users, as shown below. Leave the Password boxes blank to prevent

changing your password, then click Save to store your changes. Click OK on any warning

messages.

7 of 11

7. Click on General User under Accounts. Click on General User and the click the Modify button.

8. Click the Level 3 button to automatically check all boxes on the page. Save when finished.

8 of 11

9. Click Network to bring up the network settings screen shown below.

10. Click Static in the Connection Mode to bring up the screen below.

11. Set the IP address to the desired value: we suggest setting the first camera to 192.168.0.80, the

second to 192.168.0.81, and so forth. Check the other settings so they match the screen above,

then click Save to save the settings.

9 of 11

12. If prompted, click to Restart to restart the camera. Note that the camera is now at a different IP

address, so the browser window won’t show the camera.

13. Go to the address line in the browser, and put in the new IP address as shown below:

14. This brings up the camera’s home page shown below:

15. The camera is now at the correct IP address with the correct settings.

16. Close the browser.

10 of 11

OTION

ETECTION FOR

OME

OGIC

DVR

ONFIGURATION

To use Panasonic IP Cameras with the HomeLogic DVR tab, enter the web configuration by typing the

camera IP into the browser and logging on using your username and password. Click Setup, and then

below Buffer/Transfer click Motion Detection. Threshold is the measure of the camera’s sensitivity to

change—a lower setting will cause it pick up smaller changes. Sensitivity affects the light sensitivity—a

higher setting will result in more frequent detections of lighting changes.

Typically, the Threshold should be set to the LOWEST setting and Sensitivity should be set to the

HIGHEST.

Please see the DVR Integration Note for full details on setting up the DVR tab in HomeLogic.

Autres manuels pour BL-C111A - Network Camera - Pan

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Panasonic Caméra de sécurité

Panasonic

Panasonic WV-SW550 Series Manuel utilisateur

Panasonic

Panasonic AW-HE40HWP Manuel utilisateur

Panasonic

Panasonic BB-HCM705A - Fixed MP H.264 Dome POE Indoor Network... Manuel utilisateur

Panasonic

Panasonic GPKS152 - CCD CAMERA Manuel utilisateur

Panasonic

Panasonic GP-KR521 Manuel utilisateur

Panasonic

Panasonic WVNP244 - COLOR CCTV CAMERA Manuel utilisateur

Panasonic

Panasonic WV-CF374E Manuel utilisateur

Panasonic

Panasonic KX-HCM250 Manuel utilisateur

Panasonic

Panasonic WV-BF320 Manuel utilisateur

Panasonic

Panasonic GP-KS1000E Manuel utilisateur

Panasonic

Panasonic CQDF602U - AUTO RADIO/CD DECK Manuel utilisateur

Panasonic

Panasonic BB-HCM581A - Network Camera Pan Manuel utilisateur

Panasonic

Panasonic WV-CP620 Manuel utilisateur

Panasonic

Panasonic WVBP70 - CCTV CAMERA Manuel utilisateur

Panasonic

Panasonic WVBP120 - CCTV CAMERA Manuel utilisateur

Panasonic

Panasonic Micro SD AW-HN40HWPC Manuel utilisateur

Panasonic

Panasonic WV-CP310 Manuel utilisateur

Panasonic

Panasonic AW-E750E Manuel utilisateur

Panasonic

Panasonic AK-HC1500G Manuel utilisateur

Panasonic

Panasonic GP-KR521 Manuel utilisateur

Panasonic

Panasonic KX-HNC850 Manuel utilisateur

Panasonic

Panasonic WV-SF138 Manuel d'installation et d'exploitation

Panasonic

Panasonic WV-SPN6R481 Manuel utilisateur

Panasonic

Panasonic WV-SFV481 Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur