Panasonic WV-V1330LK Manuel utilisateur

Frequently Asked Questions for WV-V Series models

December, 2016

No. Questions Answers

Forgottn User Name or Password.

How I can initialize it?

Please refer to the supplied Installation Guide (IG) how to initialize it by INITIAL SET button.

For WV-V1330LK, please refer to the following page.

But please note that all settings will be restored to the factory defalt settings.

No live picture can be seen.

Or, failure to install plug-in software

(unable to install plag-in software)

with an error message.

Plug-in software must be installed properly to see live picture.

Please install the plug-insoftware with the procedures as follow;

1. Close Internet Explorer.

2. Delete the folder of "webrec" under "c:\Program Files".

3. Access the camera and install the plug-in software with following the instruction s on the screen.

Or, insall the plug-in software using with the supplied CD-ROM as follows;

1. Mount the CD-ROM on to your drive.

2. Run "CDLauncher.exe".

3. Click "Install" button at "Viewer Software" to start installing the plug-in software.

3Further inquiries

For U.S. and Canada:

Panasonic System Communications Company of North America,

Unit of Panasonic Corporation of North America

www.panasonic.com/business/

For customer support, call 1.800.528.6747

Two Riverfront Plaza, Newark, NJ 07102-5490

Panasonic Canada Inc.

5770 Ambler Drive, Mississauga, Ontario, L4W 2T3 Canada

(905)624-5010

www.panasonic.ca

[1] Remove the sunshade from the camera body.

Sunshade

Sunshade fixing screw

[2] Remove the front cover from the camera body.

Front cover

(1) Place the camera so that it is facing upward, and grip the camera body with one hand.

(2) Turn the front cover counterclockwise, and remove it from the camera body.

(1)

(2)

[3] Confirm the position of the RESET button, and press

the button.

(1) Grasp the metal fitting in which the lens is mounted, lift it up slightly, as shown in the

picture as follow, and confirm the position of the RESET button on the circuit board.

(2) Power on the camera, and wait for one minute. (During this time the camera starts up.)

(3) Use a pin made of a non-conductive material to hold down the RESET button for 10

seconds, then release it.

(4) Confirm that the camera starts up normally.

Ran the [IP Setting Software], selected the camera that was initialized, and click [Access

Camera]. If the administrator registration window comes up, initialization has completed

successfully.

(5) Power off the camera.

Metal fitting

Lens Press the RESET button

[4] Reverse steps [2] and [1] above to return the front

cover and sunshade to their original positions.

IMPORTANT：

Make sure to perform the reset operation in an indoor location where no drops of water

can fall on the product.

Exercise caution regarding the ambient humidity of the location where the reset operation

is performed. (Choose a location with low humidity.)

Check to make sure that the camera is powered off when opening up the front cover and

lifting up slightly the metal fitting in which the lens is mounted.

Do not touch the electricalcomponents on the circuit board.

When turning the front cover clockwise to reattach it after resetting the camera, make sure

to tighten it securely. (If the front cover is not tightened securely, the moisture protection

functionality may be lost.)

After completing the operation, wipe the transparent panel on the front cover with cleaning

tissue or the like to clean it. (If fingerprints, etc., are left on the front cover, the picture

quality may be affected.)

Initializing the Panasonic Network Camera, Model WV-V1330LK

(1) Remove the screw.

(2) Then, remove the sunshade.

Ce manuel convient aux modèles suivants

Autres manuels Panasonic Caméra de sécurité

Panasonic

Panasonic BB-HCM381 Manuel utilisateur

Panasonic

Panasonic KX-HNC600AZ Manuel utilisateur

Panasonic

Panasonic WVBL734 - CCTV CAMERA Manuel utilisateur

Panasonic

Panasonic BB-HCM515A - Network Camera w/ Audio Manuel utilisateur

Panasonic

Panasonic KX-TGA914E Manuel utilisateur

Panasonic

Panasonic WV-NW484S - i-Pro Network Camera Manuel utilisateur

Panasonic

Panasonic GPMF552 - ICD CAMERA Manuel utilisateur

Panasonic

Panasonic WV-SW172 Manuel utilisateur

Panasonic

Panasonic WV-CS850B Manuel utilisateur

Panasonic

Panasonic WVBP554 - CCTV B/W CAMERA Manuel utilisateur

Panasonic

Panasonic WV-SP500 Series Manuel utilisateur

Panasonic

Panasonic K-EW114L03E Manuel utilisateur

Panasonic

Panasonic WV-CW374 Manuel utilisateur

Panasonic

Panasonic WVNS324 - NETWRK CLR DOME CAME Manuel utilisateur

Panasonic

Panasonic Super Dynamic III WV-CS954 Manuel utilisateur

Panasonic

Panasonic WV-CW474A Series Manuel utilisateur

Panasonic

Panasonic WVCP160 - COLOR CCTV CAMERA Manuel utilisateur

Panasonic

Panasonic BL-C30 Manuel utilisateur

Panasonic

Panasonic BL-C111 Manuel utilisateur

Panasonic

Panasonic BB-HCM403 Manuel utilisateur

Panasonic

Panasonic GP-KS1000E Manuel utilisateur

Panasonic

Panasonic WVCF254 - COLOR CAMERA Manuel utilisateur

Panasonic

Panasonic WV-SW316 Manuel utilisateur

Panasonic

Panasonic BB-HCM511A Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur