Panasonic A-88-V Manuel utilisateur

Bullet Network Camera

Quick Start Guide

All trademarks are the property of their respective owners.

Quick Start Guide

About this Manual

This Manual is applicable to Bullet Network Camera.

The Manual includes instructions for using and managing the prod-

uct. Pictures, charts, images and all other information hereinafter

are for description and explanation only. The information contained

in the Manual is subject to change, without notice, due to rmware

updates or other reasons. Please use this user manual under the

guidance of professionals.

Legal Disclaimer

REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE

USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS.

OUR COMPANY SHALL NOT TAKE ANY RESPONSIBILITES FOR

ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAM-

AGES RESULTING FROM CYBER ATTACK, HACKER ATTACK,

VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS;

HOWEVER, OUR COMPANY WILL PROVIDE TIMELY TECHNICAL

SUPPORT IF REQUIRED.

SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE

CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE

USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR

USE CONFORMS THE APPLICABLE LAW. OUR COMPANY

SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS

USED WITH ILLEGITIMATE PURPOSES.

IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL

AND THE APPLICABLE LAW, THE LATER PREVAILS.

Regulatory Information

FCC Information

Please take attention that changes or modification not expressly ap-

proved by the party responsible for compliance could void the user’s

authority to operate the equipment.

FCC compliance: This equipment has been tested and found to com-

ply with the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equip-

ment generates, uses and can radiate radio frequency energy and, if

not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or

more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help

FCC conditions

This device complies with part 15 of the FCC Rules. Operation is sub-

ject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interfer-

ence that may cause undesired operation.

EU Conformity Statement

This product and - if applicable - the supplied accessories

too are marked with "CE" and comply therefore withthe

applicable harmonized European standards listed under

the the EMC Directive 2014/30/EU, the RoHS Directive

2011/65/EU.

not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or

more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help

FCC conditions

This device complies with part 15 of the FCC Rules. Operation is sub-

ject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interfer-

ence that may cause undesired operation.

EU Conformity Statement

This product and - if applicable - the supplied accessories

too are marked with "CE" and comply therefore withthe

applicable harmonized European standards listed under

the the EMC Directive 2014/30/EU, the RoHS Directive

2011/65/EU.

2012/19/EU (WEEE directive): Products marked with

this symbol cannot be disposed of as unsorted municipal

waste in the European Union. For proper recycling,

return this product to your local supplier upon the

purchase of equivalent new equipment, or dispose of

it at designated collection points. For more information

see: www.recyclethis.info

2006/66/EC and its amendment 2013/56/EU (battery

directive): This product contains a battery that cannot

be disposed of as unsorted municipal waste in the

European Union. See the product documentation for

specific battery information. The battery is marked with

this symbol, which may include lettering to indicate

cadmium (Cd), lead (Pb), or mercury (Hg). For proper

recycling, return the battery to your supplier or to a

designated collection point. For more information see:

www.recyclethis.info.

Industry Canada ICES-003 Compliance

This device meets the CAN ICES-3 (B)/NMB-3(B) standards require-

ments.

Safety Instruction

These instructions are intended to ensure that the user can

use the product correctly to avoid danger or property loss.

Laws and Regulations

The device should be used in compliance with local laws,

electrical safety regulations, and re prevention regulations.

Transportation

Keep the device in original or similar packaging while

transporting it.

Power Supply

The input voltage should conform to IEC60950-1 standard:

SELV (Safety Extra Low Voltage) and the Limited Power

Source. Refer to the appropriate documentation for detailed

information.

DO NOT connect multiple devices to one power adapter, to

avoid over-heating or re hazards caused by overload.

Make sure the plug is properly connected to the power

socket.

System Security

The installer and user are responsible for password and

security conguration and its settings.

Battery

Improper use or replacement of the battery may result in

explosion hazard. Replace with the same or equivalent

type only. Dispose of used batteries in conformance with

the local codes.

Maintenance

If the product does not work properly, please contact your

dealer or the nearest service center. We shall not assume

any responsibility for problems caused by unauthorized

repair or maintenance.

Safety Instruction

These instructions are intended to ensure that the user can

use the product correctly to avoid danger or property loss.

Laws and Regulations

The device should be used in compliance with local laws,

electrical safety regulations, and re prevention regulations.

Transportation

Keep the device in original or similar packaging while

transporting it.

Power Supply

The input voltage should conform to IEC60950-1 standard:

SELV (Safety Extra Low Voltage) and the Limited Power

Source. Refer to the appropriate documentation for detailed

information.

DO NOT connect multiple devices to one power adapter, to

avoid over-heating or re hazards caused by overload.

Make sure the plug is properly connected to the power

socket.

System Security

The installer and user are responsible for password and

security conguration and its settings.

Battery

Improper use or replacement of the battery may result in

explosion hazard. Replace with the same or equivalent

type only. Dispose of used batteries in conformance with

the local codes.

Maintenance

If the product does not work properly, please contact your

dealer or the nearest service center. We shall not assume

any responsibility for problems caused by unauthorized

repair or maintenance.

A few device components (e.g., electrolytic capacitor)

require regular replacement. The average lifespan varies,

so periodic checking is recommended. Contact your dealer

for details.

Cleaning

Please use a soft and dry cloth when clean inside and

outside surfaces of the product cover. Do not use alkaline

detergents.

Using Environment

When any laser equipment is in use, make sure that the

device lens is not exposed to the laser beam, or it may burn

out.

Do not expose the device to high electromagnetic radiation

or dusty environments.

For indoor-only device, place it in a dry and well-ventilated

environment.

Do not aim the lens at the sun or any other bright light.

Make sure the running environment meets the requirement

of the device. The operating temperature shall be -30 °C to

60 °C (-22 °F to 140 °F), and the operating humidity shall

be 95% or less (no condensing).

Do not place the camera in extremely hot, cold,

dusty or damp locations, and do not expose it to high

electromagnetic radiation.

Emergency

If smoke, odor, or noise arises from the device, immediately

turn off the power, unplug the power cable, and contact the

service center.

Time Synchronization

Set up camera time manually for the rst time access if the

local time is not synchronized with that of the network. Visit

the camera via Web browse/client software and go to time

settings interface.

Installation

Make sure the device is rmly secured to any wall or ceiling

mountings.

Be sure that there is enough space to install the camera

and accessories.

Make sure that the device in the package is in good

condition and all the assembly parts are included.

Make sure that the wall is strong enough to withstand at

least 4 times the weight of the camera and the mount.

The standard power supply is 12 VDC, please make sure

your power supply matches with your camera.

Make sure that the power has been disconnected before

you wire, install, or disassemble the device.

Make sure that no reflective surface is too close to the

camera lens. The IR light from the camera may reect back

into the lens causing reection.

Symbols and Marks

Notice

Warning

Forbidden

Set up camera time manually for the rst time access if the

local time is not synchronized with that of the network. Visit

the camera via Web browse/client software and go to time

settings interface.

Installation

Make sure the device is rmly secured to any wall or ceiling

mountings.

Be sure that there is enough space to install the camera

and accessories.

Make sure that the device in the package is in good

condition and all the assembly parts are included.

Make sure that the wall is strong enough to withstand at

least 4 times the weight of the camera and the mount.

The standard power supply is 12 VDC, please make sure

your power supply matches with your camera.

Make sure that the power has been disconnected before

you wire, install, or disassemble the device.

Make sure that no reflective surface is too close to the

camera lens. The IR light from the camera may reect back

into the lens causing reection.

Symbols and Marks

Notice

Warning

Forbidden

Correct

Incorrect

Turn to page A and continue.

i. Not necessarily included accessory.

ii. Variable accessory amount.

iii. Skip this step if not required.

MicroSD card

Grounding

Disposal

Purchase separately

Other situations

Other situations omitted

Waterproof

Skip this step if not necessary

Table des matières

Autres manuels Panasonic Caméra de sécurité

Panasonic

Panasonic VL-WD812BX Manuel technique

Panasonic

Panasonic AWE860 - COLOR CAMERA Manuel utilisateur

Panasonic

Panasonic KX-HNC805C Manuel utilisateur

Panasonic

Panasonic GPMF552 - ICD CAMERA Manuel utilisateur

Panasonic

Panasonic AJ-D910WBP Manuel utilisateur

Panasonic

Panasonic WV-CL500 Manuel utilisateur

Panasonic

Panasonic WV-NW484S - i-Pro Network Camera Manuel utilisateur

Panasonic

Panasonic IDEHAL WV-SUD638PJ Manuel utilisateur

Panasonic

Panasonic BL-C1 Manuel utilisateur

Panasonic

Panasonic WV-BP140 Manuel utilisateur

Panasonic

Panasonic WVNM100 - NETWORK COLOR CAMERA Manuel utilisateur

Panasonic

Panasonic WVCL920 - COLOR CAMERA Manuel utilisateur

Panasonic

Panasonic i-Pro WV-SF336 Manuel utilisateur

Panasonic

Panasonic Micro SD AW-HN40HWPC Manuel utilisateur

Panasonic

Panasonic GPMF502 - ICD CAMERA Manuel utilisateur

Panasonic

Panasonic KX-HCM10 Manuel utilisateur

Panasonic

Panasonic WV-CP470 Series Manuel utilisateur

Panasonic

Panasonic WV-SP105 Manuel utilisateur

Panasonic

Panasonic VL-SDM100BX Manuel utilisateur

Panasonic

Panasonic BB-HCM331 Manuel utilisateur

Panasonic

Panasonic BL-C30A - Wireless 802.11 b/g Network Camera Mode d’emploi

Panasonic

Panasonic AWE300S - SEPERATE CAMERA Manuel utilisateur

Panasonic

Panasonic Super Dynamic III WV-CS950 Manuel utilisateur

Panasonic

Panasonic WV-CW7CN Manuel utilisateur

Manuels Caméra de sécurité populaires d'autres marques

Okina USA

Okina USA SIR36-870VF650LP Manuel utilisateur

Divio

Divio NDR155PA Manuel utilisateur

Canon

Canon VB-C500D Manuel utilisateur

Easy Access

Easy Access EasyGuard Manuel utilisateur

Vivotek

Vivotek FD9389-EHV-v2 Manuel utilisateur

TUYA

TUYA COSMO W2 Manuel utilisateur

Eusso

Eusso UNC7500-IR Guide de configuration

urmet domus

urmet domus 1096/204 Manuel utilisateur

VC VC20 series Manuel utilisateur

Axis

Axis Q1614 Manuel utilisateur

ieGeek

ieGeek DD201 Manuel utilisateur

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuel utilisateur

Vicon

Vicon V662-D-1 Mode d'emploi

Grundig

Grundig GCH-K0274P Manuel utilisateur

Lorex

Lorex VANTAGE LBC7032 Manuel utilisateur

4xem

4xem WPT Manuel utilisateur

Samsung

Samsung SCV-3082 Manuel utilisateur

Vitek

Vitek VTC-C544 Manuel utilisateur