Panasonic PTAE100U - LCD PROJECTOR Manuel utilisateur

ORDER NO. VED0110325C0

D10

LCD Projector

PT-AE100U / PT-AE100E

SPECIFICATIONS

LCD Projector 1

1. Safety Precautions 3

1.1. General Guidelines 3

1.2. Leakage Current Check 4

1.3. UV Precaution and UHM Lamp Precautions 4

2. Ext Option 5

2.1. Procedure to enter EXT OPTION 5

2.2. EXT OPTION Menu and Functions 5

2.3. Canceling EXT OPTION 7

3. Self-Check Mode 7

3.1. Procedure to enter the self-check mode 7

3.2. Self Check Display and Contents 7

3.3. Canceling the self-check mode 7

4. Service Mode 7

4.1. Procedure to enter the service mode 8

4.2. Canceling the service mode 8

5. Disassembly Instructions 8

5.1. Printed Circuit Board and Main Parts Location 8

5.2. Removal of Upper Case 10

5.3. Removal of A-P.C.Board 11

5.4. Removal of K-Module 11

5.5. Removal of S-P.C.Board 12

5.6. Removal of R-P.C.Board 13

5.7. Removal of B-Module 13

5.8. Removal of P-Module 14

5.9. Removal of Lamp Unit 15

5.10. Removal of Analysis Block, LCD Block and Lens Block 16

5.11. Replacement of Polarizer 17

5.12. Replacement of PBS Array (Analysis Block) 18

6. Measurement and Adjustments 20

6.1. Adjustment Procedure Flowchart 20

6.2. Cautions for Adjustment 20

6.3. Setting Before Adjustment 20

6.4. Software for Adjustment 20

6.4.1. Outline 20

6.4.2. Operating Procedure 21

6.4.3. Port Selection Menu 21

6.4.3.1. Explanation of Buttons 21

6.4.4. Data Send/Receive Menu 22

6.4.4.1. Explanation of Buttons 22

6.4.4.2. Receiving and sending of the data 23

6.4.5. Adjustment Menu 23

6.4.5.1. Explanation of Buttons 23

6.5. Flicker Adjustment 24

6.5.1. Adjustment Menu 24

6.5.2. Explanation of Buttons 25

6.5.3. Equipment to be used 26

6.5.4. Adjustment Procedure 26

6.6. Input Level Adjustment (RGB) 26

6.6.1. Adjustment Menu 26

6.6.2. Explanation of Buttons 27

svcdoc

6.6.3. Equipment to be used 27

6.6.4. Adjustment Procedure 27

6.7. Input Level Adjustment (YPBPR) 27

6.7.1. Adjustment Menu 27

6.7.2. Explanation of Buttons 27

6.7.3. Equipment to be used 28

6.7.4. Adjustment Procedure 28

6.8. Input Level Adjustment (VIDEO) 28

6.8.1. Adjustment Menu 28

6.8.2. Explanation of Buttons 28

6.8.3. Equipment to be used 28

6.8.4. Adjustment Procedure 28

6.9. Ghost Adjustment 28

6.9.1. Adjustment Menu 28

6.9.2. Explanation of Buttons 29

6.9.3. Equipment to be used 29

6.9.4. Adjustment Procedure 30

7. Troubleshooting 30

8. Interconnection Block Diagram 37

8.1. Interconnection Block Diagram (1/2) 37

8.2. Interconnection Block Diagram (2/2) 37

9. Block Diagram 37

9.1. Power Supply 37

9.2. Signal Processing (1/2) 37

9.3. Signal Processing (2/2) 37

10. Schematic Diagram 37

10.1. A-P.C.Board (1/4) 38

10.2. A-P.C.Board (2/4) 38

10.3. A-P.C.Board (3/4) 38

10.4. A-P.C.Board (4/4) 38

10.5. S-P.C.Board, R-P.C.Board 38

10.6. B-Module 38

11. Circuit Boards 38

11.1. A-P.CBoard (Foil Side) S-P.C.Board 38

11.2. A-P.C.Board (Component Side) 38

12. Terminal guide of ICs and transistors 38

13. Exploded Views 39

14. Replacement Parts List 40

15. Schematic Diagram for printing with A4 size 77

svcdoc

Unauthorized copying and distribution is a violation of law.

1. Safety Precautions

1.1. General Guidelines

- For continued safety, no modification of any circuit must be attempted.

- Unplug the power cord from the power outlet before disassembling this

projector.

- It is advisable to use an isolation transformer in the AC power line

before the service.

- Observe the original lead dress during the service. If a short circuit is

found, replace all the parts overheated or damaged by the short circuit.

- After the service, all the protective devices such as insulation barriers,

insulation papers, shields, and isolation R-C combinations must be

properly installed.

- After the service, check the leakage current to prevent the customer

from getting an electric shock.

1.2. Leakage Current Check

1. Prepare the measuring circuit as shown in Fig.1.

Be sure to use a voltmeter having the performance described in Table

Fig. 1

Table 1

Fig. 2

2. Assemble the circuit as shown in Fig. 2. Plug the power cord in a

power outlet.

3. Connect M1 to T1 according to Fig. 2 and measure the voltage.

4. Change the connection of M1 from T1 to T2 and measure the voltage

again.

5. The voltmeter must read 0.375 V or lower in both of steps 3 and 4. This

means that the current must be 0.75 mA or less.

6. If the reading is out of the above standard, the projector must be

repaired and rechecked before returning to the customer because of a

possibility of an electric shock.

1.3. UV Precaution and UHM Lamp Precautions

- Be sure to unplug the power cord from the power outlet when replacing

the lamp.

- Because the lamp reaches a very high temperature during its operation,

wait until it cools completely when replacing the Lamp Unit.

- The lamp emits small amounts of UV-radiation, avoid direct-eye contact

with the light.

- Because the high pressure lamp involves a risk of explosion, never

touch the lamp wire lead during the service. (See Fig. 3)

Fig. 3

2. Ext Option

This projector has EXT OPTION in addition to standard on-screen menus.

- There are SELF CHECK and SERVICE MODE for service, etc.

2.1. Procedure to enter EXT OPTION

1. Press "MENU" button on the remote control unit to display "MENU"

screen, then select "OPTION" and press "ENTER" button.

2. Select "OSD" on "OPTION" menu and press "ENTER" button 3

seconds or longer.

MENU OPTION OSD

2.2. EXT OPTION Menu and Functions

- FREEZE MSG

Switching ON/OFF "FREEZE" on-screen display

- PIC.SHIFT

Switching ON/OFF the antipersistence function

- Shifts the picture slightly (by one dot) when every 60 minutes. (one dot

shifting three times, one dot shifting three times in reverse direction,

and repeats them alternately.)

- RUNTIME PRT

Switching ON/OFF the shutdown when the operation time for the lamp

unit is 2 000 hours or longer

- FAN CONTROL

Setting the cooling fan motor rotation mode

- NORMAL: Normal setting

- HIGH: Highlands mode

- FULL: High-speed

Notes:

- Must set HIGH when using the projector at highlands as 1 400 meters

or higher above sea level.

- Not to use the projector at highlands exceeding 2 700 meters above sea

level.

- AUTOSETUP

Setting AUTO SETUP mode

- NORMAL: To set the normal mode (the dot clock is adjusted strictly)

- SPECIAL: To set the special mode (the dot clock is adjusted roughly)

* Do not change the initial setting (NORMAL).

- SELF CHECK

To enter the self-check mode

- SERVICE MODE

To enter the service mode

2.3. Canceling EXT OPTION

Press "MENU" button on the remote control unit.

3. Self-Check Mode

This mode is used to narrow down the location of the failure.

3.1. Procedure to enter the self-check mode

Select "SELF CHECK" on "EXT OPTION" menu and press "ENTER" button on the remote control unit.

3.2. Self Check Display and Contents

3.3. Canceling the self-check mode

Press "MENU" button on the remote control unit.

4. Service Mode

This mode is used to display three kinds of test patterns [Horizontal lines, Vertical lines, Dots and

White (No pattern)] in the four colors (White, Red, Green and Blue).

Note:

- On the service mode, displays above patterns by each color without

test equipment such as PC or SG. Use the service mode for simplified

adjustments by your eyes and so on.

4.1. Procedure to enter the service mode

Select "SERVICE MODE" on "EXT OPTION" menu and press "ENTER" button on the remote control

unit.

Note:

- In the service mode, pressing the up-arrow " " or down-arrow " "

button on the remote control unit allows the testpattern selection and

the left-arrow " " or right-arrow " " button the color selection (White /

Red / Green / Blue).

4.2. Canceling the service mode

Press "MENU" button on the remote control unit.

5. Disassembly Instructions

Warning:

- Be sure to unplug the power cord from the power outlet before

disassembling this projector.

Caution:

- While turning over a printed circuit board, be sure to put a insulating

material under it to prevent a short circuit.

- Printed circuit boards and wires must not be pulled forcibly, but be

handled carefully.

- Connectors also must be handled carefully.

- After repairing this projector, be sure to put back the wires and

connectors to the original condition.

5.1. Printed Circuit Board and Main Parts Location

Electrical Parts

Autres manuels pour PTAE100U - LCD PROJECTOR

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Panasonic Projecteur

Panasonic

Panasonic PTP1SDU - LCD PROJECTOR Manuel utilisateur

Panasonic

Panasonic PT-VW431DU Manuel utilisateur

Panasonic

Panasonic PT-LB75VEA Manuel utilisateur

Panasonic

Panasonic PT-RQ13K Manuel utilisateur

Panasonic

Panasonic PT-LB10 Manuel utilisateur

Panasonic

Panasonic PT-REZ80 Manuel utilisateur

Panasonic

Panasonic PT-61HX40 Manuel utilisateur

Panasonic

Panasonic PT-D10000 Series Manuel utilisateur

Panasonic

Panasonic PT-D9510U Manuel utilisateur

Panasonic

Panasonic PT-L735 Manuel du système

Panasonic

Panasonic DLP PT-D12000U Manuel utilisateur

Panasonic

Panasonic PT-LB50E Manuel utilisateur

Panasonic

Panasonic PT-AE700U Manuel utilisateur

Panasonic

Panasonic PTL501U - LCD PROJECTOR Manuel utilisateur

Panasonic

Panasonic PTLB20U - LCD PROJECTOR - MULTI-LANG Manuel utilisateur

Panasonic

Panasonic LB75U - XGA LCD Projector Manuel utilisateur

Panasonic

Panasonic PTF300U - LCD PROJECTOR Manuel utilisateur

Panasonic

Panasonic PT-LZ370U Manuel utilisateur

Panasonic

Panasonic PT-TW231R Manuel du système

Panasonic

Panasonic PTAE700U-EC Operating Manuel utilisateur

Panasonic

Panasonic PT-RZ12K Manuel utilisateur

Panasonic

Panasonic PT-L6510U Manuel utilisateur

Panasonic

Panasonic PT-TW230E Manuel utilisateur

Panasonic

Panasonic PT-LZ370 Manuel utilisateur

Manuels Projecteur populaires d'autres marques

iEmmet

iEmmet MP-312 Manuel utilisateur

Epson

Epson VS400 Manuel utilisateur

Sony

Sony VPL-HS10 Marketing Specifications & Features Manuel utilisateur

Sony

Sony VPL-HW65ES Manuel de service

Toshiba

Toshiba TLP-791U Manuel utilisateur

Philips

Philips LC1341 Guide de référence

NEC

NEC NP600S EDU Manuel utilisateur

BenQ

BenQ SH753P Manuel utilisateur

Eiki

Eiki EK-623U series Manuel utilisateur

Epson

Epson PowerLite Pro Cinema 6020UB Manuel utilisateur

Epson

Epson PowerLite Home Cinema 705HD Manuel utilisateur

Christie

Christie LHD700 Manuel utilisateur

Navitar

Navitar FX Manuel utilisateur

InFocus

InFocus LitePro 560 Manuel utilisateur

Sony

Sony SRX-R815P Manuel utilisateur

Vivitar

Vivitar DP1500 X Manuel utilisateur

Acer

Acer C20 Series Manuel utilisateur

Asus

Asus ZenBeam Latte Manuel utilisateur