Panasonic PT AE1000E Manuel utilisateur
TQDJ19046
CEILING MOUNT BRACKET SAFEGUARDS
The projector and the ceiling mount bracket are designed sufficiently safety though, make sure the safety cable provided
with the projector is installed and attached to the bottom of the projector when mounting in the ceiling for safety and security.
JInstalling the safety cable
1. Install the ceiling mount bracket according to the Installation Instructions.
2. Loop the security cable around the ceiling mount bracket with less slack.
• Lace the cable of the end with a latch through the loop on the other end of the cable.
3. Attach the latch on to the bottom of the projector with a provided screw.
• Torque: 125±20 N·cm
NOTE:
• Even if it is guarantee period, the manufacturer is not responsible for any hazard or damage caused by using a ceiling mount
bracket which is not purchased from an authorised distributors, or environmental conditions.
• Make sure to use a torque driver and do not use an electrical screwdriver or an impact screwdriver.
• Installation work of the ceiling mount bracket should only be carried by a qualified technician.
• Remove an unused ceiling mount bracket promptly.
AE1000_Leaflet_Wire&Lamp.fm Page 1 Wednesday, October 25, 2006 10:48 AM
S1006-0A
ERRATA
JOpening the top cover
(Operating Instructions
page 42)
1. Turn off the MAIN POWER switch
according to the procedure “Switching
the projector on/off” on page 19 and
disconnect the mains plug from the mains
socket.
• Make sure the Lamp unit and the
surroundings are cooled enough.
2. Open the top cover of the projector and
remove aside. See “Back and bottom
view” on page 13.
• Hold the top cover up and press one of the
buttons of the hinge parts each to remove.
JOpening the top cover (Operating
Instructions page 42)
1. Turn off the MAIN POWER switch according to the
procedure “Switching the projector on/off” on page 19
and disconnect the mains plug from the mains socket.
• Make sure the Lamp unit and the surroundings are
cooled enough.
2. Hold at the back corner of the Top cover and slightly
push up to open.
3. Unhook the top cover safety hook from the projector.
4. Hold the top cover up and press one of the buttons of
the hinge parts each to remove.
• When the projector is mounted in the ceiling, removing
the hinge parts is not required.
5. Remove the top cover aside.
NOTE: When the projector is mounted in the ceiling;
• Place yourself at back side of the projector, then open and
close the top cover.
• Do not work directly under the projector or put your face closer
to the projector.
Press here
Press here
Top cover safety hook Hinge parts
Press here
Top cover
Top cover
JAttaching the top cover
(Operating Instructions
page 43)
1. Attach the hinge parts of the top cover to
the projector and press slightly until it
clicks
2. Hook the tabs of the top cover to the
projector and lift down slowly.
3. Press the back corner of the top cover
gently until it clicks.
JAttaching the top cover (Operating
Instructions page 43)
1. Attach the hinge parts of the top cover to the
projector and press slightly until it clicks.
• When the projector is mounted in the ceiling, attaching
the hinge parts is not required.
2. Hook the top cover safety hook to the projector.
3. Hooking the tabs of the top cover to the front of the
projector and lift down slowly.
4. Press the back corner of the top cover gently until it
clicks.
NOTE:
• Ensure to hook the top cover safety hook to the body.
Top cover safety hook Tab
Top cover
AE1000_Leaflet_Wire&Lamp.fm Page 2 Wednesday, October 25, 2006 10:48 AM
TQDJ19046
CEILING MOUNT BRACKET SAFEGUARDS
The projector and the ceiling mount bracket are designed sufficiently safety though, make sure the safety cable provided
with the projector is installed and attached to the bottom of the projector when mounting in the ceiling for safety and security.
JInstalling the safety cable
1. Install the ceiling mount bracket according to the Installation Instructions.
2. Loop the security cable around the ceiling mount bracket with less slack.
• Lace the cable of the end with a latch through the loop on the other end of the cable.
3. Attach the latch on to the bottom of the projector with a provided screw.
• Torque: 125±20 N·cm
NOTE:
• Even if it is guarantee period, the manufacturer is not responsible for any hazard or damage caused by using a ceiling mount
bracket which is not purchased from an authorised distributors, or environmental conditions.
• Make sure to use a torque driver and do not use an electrical screwdriver or an impact screwdriver.
• Installation work of the ceiling mount bracket should only be carried by a qualified technician.
• Remove an unused ceiling mount bracket promptly.
AE1000_Leaflet_Wire&Lamp.fm Page 1 Wednesday, October 25, 2006 10:48 AM
S1006-0A
ERRATA
JOpening the top cover
(Operating Instructions
page 42)
1. Turn off the MAIN POWER switch
according to the procedure “Switching
the projector on/off” on page 19 and
disconnect the mains plug from the mains
socket.
• Make sure the Lamp unit and the
surroundings are cooled enough.
2. Open the top cover of the projector and
remove aside. See “Back and bottom
view” on page 13.
• Hold the top cover up and press one of the
buttons of the hinge parts each to remove.
JOpening the top cover (Operating
Instructions page 42)
1. Turn off the MAIN POWER switch according to the
procedure “Switching the projector on/off” on page 19
and disconnect the mains plug from the mains socket.
• Make sure the Lamp unit and the surroundings are
cooled enough.
2. Hold at the back corner of the Top cover and slightly
push up to open.
3. Unhook the top cover safety hook from the projector.
4. Hold the top cover up and press one of the buttons of
the hinge parts each to remove.
• When the projector is mounted in the ceiling, removing
the hinge parts is not required.
5. Remove the top cover aside.
NOTE: When the projector is mounted in the ceiling;
• Place yourself at back side of the projector, then open and
close the top cover.
• Do not work directly under the projector or put your face closer
to the projector.
Press here
Press here
Top cover safety hook Hinge parts
Press here
Top cover
Top cover
JAttaching the top cover
(Operating Instructions
page 43)
1. Attach the hinge parts of the top cover to
the projector and press slightly until it
clicks
2. Hook the tabs of the top cover to the
projector and lift down slowly.
3. Press the back corner of the top cover
gently until it clicks.
JAttaching the top cover (Operating
Instructions page 43)
1. Attach the hinge parts of the top cover to the
projector and press slightly until it clicks.
• When the projector is mounted in the ceiling, attaching
the hinge parts is not required.
2. Hook the top cover safety hook to the projector.
3. Hooking the tabs of the top cover to the front of the
projector and lift down slowly.
4. Press the back corner of the top cover gently until it
clicks.
NOTE:
• Ensure to hook the top cover safety hook to the body.
Top cover safety hook Tab
Top cover
AE1000_Leaflet_Wire&Lamp.fm Page 2 Wednesday, October 25, 2006 10:48 AM
Ce manuel convient aux modèles suivants
1
Autres manuels Panasonic Projecteur
Panasonic
Panasonic PT-DZ770K Manuel utilisateur
Panasonic
Panasonic PT-EZ770 Series Manuel utilisateur
Panasonic
Panasonic PT-EZ580 Manuel utilisateur
Panasonic
Panasonic PT-51HX41 Manuel utilisateur
Panasonic
Panasonic PT-DW5100E Guide de configuration rapide
Panasonic
Panasonic PT-CX300 Manuel utilisateur
Panasonic
Panasonic PTLW80NTU - LCD PROJECTOR - MULTI LANGUAGE Manuel utilisateur
Panasonic
Panasonic PT-LB50S Manuel utilisateur
Panasonic
Panasonic PT-F300NTEA Instructions d'installation et d'entretien
Panasonic
Panasonic PT-D7700 Manuel utilisateur
Panasonic
Panasonic PT-AE200E Manuel utilisateur
Panasonic
Panasonic PT-CW230EA Manuel utilisateur
Panasonic
Panasonic PT-VW430U Manuel utilisateur
Panasonic
Panasonic PTL701XU - LCD VIDEO PROJECTOR Manuel utilisateur
Panasonic
Panasonic PT-F200NTEA Manuel utilisateur
Panasonic
Panasonic PT-LB75EA Manuel utilisateur
Panasonic
Panasonic PT-D4000 Manuel du système
Panasonic
Panasonic PTL6600U - LCD PROJECTOR Manuel utilisateur
Panasonic
Panasonic PT-MZ570 Manuel utilisateur
Panasonic
Panasonic PT-MZ16K Manuel utilisateur
