Panasonic KX-NS Series Manuel utilisateur

Setup Reference guide for KX-NS Series

(Tested with NS1000 Ver4.5)

“I-Net Connect” SIP Trunk service

with Built-in Router

Version 1.2 (PSCEU) 11th April, 2017

SUMMARY

This document is a reference for configuring “I-Net Connect” SIP trunks onto KX-NS Series systems

and includes the settings required for Incoming Call DDI routing and Outgoing Call CLI presentation.

SIP trunk specific account details are provided to you by I-Net Connect.

Attention:

This document was created based on the results of test environment accounts.

Panasonic cannot guarantee SIP Trunk operation in all environments, however as a result of

completing this Inter-Operability Test Panasonic will provide technical support for any issues

experienced an assist as far as possible in providing a resolution.

Please obtain relevant information from Service provider before configuration of SIP trunks.

Panasonic will not be held liable for any information provided in this guidance document.

Information used in this document is for interoperability testing.

Information and Specifications in this document are subject to change without notice.

Note

When using multiple lines

It is not possible to assign two or more lines to one ID. Make multiple line agreement and obtain

multiple IDs.

Busy

If there are incoming calls when all lines are busy, the caller hears ROT instead of Busy.

Transfer / Forward

When the Transfer/forwarding destination is PSTN, the CLI is not call originator but PBX's CLI.

FAX

Fax that send to PSTN (Call to Japan PSTN) had failures by signaling filtered.

Ringing time

When receiving a call, the bell rings for 1 minute, but on the calling side it keeps calling for about

17 seconds longer.

Table of Contents

(1) Provisioning a SIP trunk: Page 3

(2) Incoming Call Routing: Page 5

(3) Outgoing Call CLI: Page 6

(4) CLIR Outgoing Call: Page 7

(5) Built-in Router and WAN settings: Page 8

(6) Packet Filtering Settings: Page 10

(1) Provisioning the SIP Trunk

SIP Trunk –Port Property

First, place the V-SIPGW Card into [OUS]condition and select [Port Property]

[Main] Tab

1. Channel Attribute: Basic Channel

2. Provider Name: Enter a name –reference only

3. SIP Server Location –Name: ipbx.inetplc.org –(I-Net Connect provided)

4. SIP Server Location –IP Address: Not required

5. SIP Server port Number: Leave at 5060

6. SIP Service Domain: Not required

7. Subscriber Number: Not required

SIP Trunk –Port Property continued

[Account] Tab

1. User name: Enter the Username as supplied by I-Net Connect.

(Note this is username without @ipbx.inetplc.org)

For example: Username = 12345670

Enter: 12345670

2. Authentication ID: Enter the Authentication ID as supplied by I-Net Connect.

(Note this is Authentication ID without @ipbx.inetplc.org)

For example: Authentication ID = 12345670

Enter: 12345670

3. Authentication Enter the password as supplied by I-Net Connect

Password: For example: password = passwordABCD

Enter: passwordABCD

[Register] Tab

1. Register Ability: Leave enabled

2. Register Interval: Enter: 120

3. Un-Register Ability: Leave enabled

4. Registrar Server –Name: Not required

5. Registrar Server –IP Address: Not required

6. Registrar Server port number: Leave at 5060

Click [OK]to apply the changes.

Select [INS] on the [V-SIPGW16] card to bring the SIP trunk ports into service.

(2) Incoming Call Routing

Go to [CO & Incoming call] and select [3.DDI /DID Table]

1. DDI/DID Number: Enter the Username in the format (as below)

Example: 12345671

Enter: 12345671

2. DDI/DID Name: Determined by the installer (optional setting)

3. DDI/DID Destination: Determined by the installer (extension number, group etc)

Click [OK].

(3) Outgoing Call CLI

Go to [V-SIPGW16] - [Port Property] and select [Calling Party] Tab

From Header –User Part: PBX-CLIP

Click [OK]

Go to [4.Extension] –[1.Wired Extension] –[1.Extension Settings] & select [CLIP] tab

Enter a valid CLI number for each required extension in the CLIP ID field.

Click [OK]

(4) CLIR Outgoing Call (Withholding Number)

Dial using the 141 prefix in order to withhold CLI presentation number.

(e.g.) 141 055 1234 0020

(5) Built-in Router and WAN Settings

NS1000 has a Built-in Router and filtering functions (Ver3.2 or later) so advanced routing

configuration can be managed by the NS1000 and the internet router/modem simply providing

internet access.

Go to [Router Configuration] - [1.Setup] - [2.WAN] - [1.Connection Settings]

Connection Mode: Select the appropriate the Connection Type.

In this example, we use the Static IP address option.

WAN IP Address: Enter your actual IP address.

Subnet Mask: Enter the appropriate subnet mask.

Gateway: Enter the actual Gateway IP address.

Preferred DNS IP Address: Enter the actual DNS IP address.

Alternative DNS IP Address: Enter the actual Alternative DNS IP address.

Click [OK].

LAN Setting.

Go to [Network Service] - [1.IP Address/Ports]

Default Gateway: Blank

* Delete the “LAN Default Gateway IP address” if it’s entered IP address.

Note: NS1000 will work as the router, Not need the LAN Gateway.

DNS IP Address: Blank

* Delete the “Preferred DNS” and “Alternative DNS”if it’s entered IP address.

Note: To use DNS address entered [Router Configuration], this field must be blank. .

Click [OK].

Perform System Reset for changes to take effect.

(6) Packet Filtering Settings

Go to [Router Configuration] - [2.Firewall] - [2.Packet Filtering]

Click [Advanced Setting]

LAN->WAN Basic Policy: Leave Accept

WAN -> LAN Basic Policy: Leave Discard

Entry No.: Select [1]

Filter: Select [Enable]

Autres manuels pour KX-NS Series

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Panasonic PBX

Panasonic

Panasonic HYBRID IP-PBX KX-TDA100 Manuel utilisateur

Panasonic

Panasonic KX-TDE200 Manuel utilisateur

Panasonic

Panasonic KX-TDE100 Manuel utilisateur

Panasonic

Panasonic KX-TD816 Manuel utilisateur

Panasonic

Panasonic KX-TDE100 Manuel utilisateur

Panasonic

Panasonic KX-NCP500 Instructions de montage

Panasonic

Panasonic KX-TA824 Manuel du propriétaire

Panasonic

Panasonic KX-TA308 Manuel utilisateur

Panasonic

Panasonic KX-TA308 Manuel utilisateur

Panasonic

Panasonic KX-TDA30 Manuel du propriétaire

Panasonic

Panasonic KX-NS700 Manuel utilisateur

Panasonic

Panasonic KX-TVP200 Manuel utilisateur

Panasonic

Panasonic KX-TDE100 Manuel utilisateur

Panasonic

Panasonic KX-TD816 Fiche technique

Panasonic

Panasonic KX-TDA600BX Manuel utilisateur

Panasonic

Panasonic KX-NCP500 Manuel utilisateur

Panasonic

Panasonic KX-NS1000 Manuel utilisateur

Panasonic

Panasonic KX-NS1000 Fiche technique

Panasonic

Panasonic KX-NS1000 Manuel utilisateur

Panasonic

Panasonic KX-TDA600 - Hybrid IP PBX Control Unit Max. 1008... Manuel utilisateur

Panasonic

Panasonic KX-TD612NZ Manuel utilisateur

Panasonic

Panasonic KX-NCP500 Manuel utilisateur

Panasonic

Panasonic KX-NCP500 Manuel utilisateur

Panasonic

Panasonic KX-TDE200NZ Manuel utilisateur

Manuels PBX populaires d'autres marques

Allo.com

Allo.com Nano 2 Manuel utilisateur

ZYCOD

ZYCOD ZX50 Manuel utilisateur

LV switch

LV switch IPPBX800 Manuel d'instructions

Edge-Core

Edge-Core VST3305 Manuel utilisateur

Rauland-Borg

Rauland-Borg Telecenter IV Manuel utilisateur

Grandstream Networks

Grandstream Networks UCM6208 Manuel utilisateur

ATCOM

ATCOM IPPBX IP02 Manuel utilisateur

bintec elmeg

bintec elmeg elmeg hybird 600 Manuel utilisateur

MCK

MCK EXTender PBXgateway Manuel utilisateur

NEC

NEC SL1000 Manuel utilisateur

Epygi

Epygi Quadro Quadro 2xi Manuel utilisateur

SMC Networks

SMC Networks TigerVoIP SMCPBX10 Manuel utilisateur

AGFEO

AGFEO AC 14 analog Manuel utilisateur

Nortel

Nortel QSY22 Manuel utilisateur

Epygi

Epygi Quadro Quadro 4xa Manuel utilisateur

Samsung

Samsung NX-308 Manuel utilisateur

SpectraLink

SpectraLink Link 3000 Manuel

Allo.com

Allo.com Nano 2 Manuel utilisateur