Panasonic FV-08VRE1 Manuel utilisateur

Model No. FV-08VRE1

2-3

6-9

9-10

BACK COVER

LIST OF COMPATIBLE DIMMERS (NOT SUPPLIED)

READ AND SAVE THESE INSTRUCTIONS

Thank you for purchasing this Panasonic product.

Please read these instructions carefully before attempting to install, operate or service the Panasonic

product. Failure to comply with instructions could result in person injury or property damage.

Please explain to users how to operate and maintain the product after the installation, and

this booklet should be presented to users. Please retain this booklet for future reference.

INSTALLATION INSTRUCTIONS

GENERAL SAFETY INFORMATION

DESCRIPTION

CONTENTS

UNPACKING

SUPPLIED ACCESSORIES

DIMENSIONS

WIRING DIAGRAM

INSTALLATION (BETWEEN JOISTS MOUNTING)

MAINTENANCE (CLEANING)

MAINTENANCE (REPLACEMENT OF LED LAMP)

PRACTICAL GUIDE TO INSTALLATION

SPECIFICATIONS

PRODUCT SERVICE

property, always

GENERAL SAFETY INFORMATION

GENERAL SAFETY INFORMATION CONTINUED

Extreme

bending

Bend

repeatedly

Duct

narrow

Bend near

adaptor

Do not use this fan with any solid-state speed control device. Solid state controls may cause

harmonic distortion which can cause motor humming noise.

When this product is no longer being operated, please remove the product to prevent the

possibility of falling.

13W

LED lamp

Trim ring (ST4.2X6)

This product uses a sirocco fan driven by a capacitor motor.

It also incorporates a thermal-cut off for safety. The trim ring is a spring-loaded, quick remove type.

Refer to the Supplied Accessories list to verify that all parts are present.

(ST4.2X18)

one 13W LED lamp and produces almost

the same illumination as a standard 70W incandescent lamp.

Warning: This equipment must be installed by qualified person in accordance with the provided

installation instructions; and all applicable codes and standards. Also, any changes or

modifications not expressly approved by the party responsible for compliance could void the

user's authority to operate this equipment.

Responsible Party: Panasonic Corporation of North America

Two Riverfront Plaza, Newark, NJ 07102

Customer Support: 1-866-292-7299

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

This product may be used with optional dimmer switch in accordance with dimmer switch

instruction instructions.

Risk of Fire: Type IC-Inherently Protected, Only Use LED Lamp , Max 13W, Type GU24.

DESCRIPTION

UNPACKING

SUPPLIED ACCESSORIES

This Panasonic ventilating fan model is listed by UL under UL file No. E78414.

Trim ring

Fan body

Adaptor

Fan

Blower unit

Motor

LED lamp

Lamp cover

Junction box

Suspension bracket

Damper

Bracket cover

Fan body

Red

Motor

White

LED lamp

Junction box

Black

Capacitor

(114 C Fuse in motor)

Thermally protected

White

Earth ground

White

Neutral

Live

Black Black Black

Black Power Supply

AC 120V 60Hz

Power Supply

AC 120V 60Hz

16 5/8 (423)

5 7/8 (148) Dia.

3 7/8 (98) Dia.

6 1/2 (163) Dia.

12 3/4 (324) 1/2 (12) 7 1/2 (190)

3 3/8 (86)

8 1/4 (209)

7 6 54

123910

Down

DIMENSIONS

WIRING DIAGRAM

Please follow the installation steps as below:

1. Insert the suspension brackets into the fan body

from each side of the bracket cover. (Fig. 1)

If spacing A between center joists is 12 inches,

cut all suspension brackets along the two “C”

cuts with a hacksaw or other tools.

2. Fix suspension brackets and with screws

(ST4.2X6), but remember not to tighten the screws

up yet. (Except that the spacing is 12 inches between

joists.) (Fig. 1)

4. Fix four long screws (ST4.2X20) partially into joists

at the four marked locations. (Fig. 3)

3. Position the fan body between joists, and hold it

properly. Mark the long holes of all the four

suspension brackets on joists. (Fig. 2)

Before

After

2-“C” cuts

Fig. 1

Bracket cover

Adaptor

Suspension

bracket

Suspension

bracket

(ST4.2X6)

Screw

Unit: inches (mm)

Ceiling

Suspension

bracket

Joist

Fan body

Fig. 2

Suspension

bracket

>1/8 (3.2)

About 3/8 (9.5)

Long hole

Unit: inches (mm)

4-Long screws

(ST4.2X20)

joists Fig. 3Fig. 3

Adaptor

Tape

Damper

INSTALLATION (BETWEEN JOISTS MOUNTING)

7. Remove the knock-out hole from the junction

box cover, and remove the junction box cover.

Then secure the conduit or stress relief to the

junction box knock-out hole. (Fig. 5)

8. Refer to wiring diagram (Page 5).

Follow all the local electrical safety codes as well

as the National Electrical Code (NEC).

Using UL approved wire nuts, connect house

power wire to ventilating fan wires. (Fig.5)

9. Install a circular duct and secure it with clamps

or wire ties, and seal it with mastic or approved

duct tape. A 4 or 6-inch circular duct is needed to

connect to the relevant part of adaptor. (Fig. 6)

Fig. 6

Circular duct Duct tape

Knock-out hole Junction

box cover

Neutral to white

Conduit

Neutral to

white

Live to black

Earth ground to green

Fig. 5

Wire nut

5. Hang the fan body down from the four long screws,

and adjust the suspension brackets if necessary.

Then, tighten the four long screws up. And that, fix

the other four long screws (ST4.2X20) to other holes.

Make sure the fan body is level and square with

the joists. (Fig. 4)

6. Tighten the two screws (ST4.2X6) up (Except that

the spacing is 12 inches between joists.). Then secure

suspension bracket and to the fan body with

screws(ST4.2X18).(Fig. 4)

8-Long screws

(ST4.2X20)

2-screws

(ST4.2X6)

Fig. 4

2-screws

(ST4.2X18)

Suitable screw

fixing positions

INSTALLATION (BETWEEN JOISTS MOUNTING) CONTINUED

10. Finish ceiling work.

A circle ceiling hole ( 6 1/2 inches (165mm) dia.)

should be cut. And make sure there will be

a gap ( >1/8 inches (3.2mm )) between bottom of

fan body and ceiling. (Fig. 7)

12. Install the supplied LED lamp. (Fig. 9)

11. Unlock the lamp cover.(Fig.8)

LIGHTING UNIT POSITION

Do the following to adjust the lighting unit:

Lighting unit

(Push the

lighting unit

vertically)

Blower unit

Down

(Rotate the lighting unit)

The lighting unit position is adjustable in the range of

1/2 inches (12.7mm). The “Up” position (the factory

setting) is recommended for normal installation.

In case of Furring Strap Joist installation, the “Down”

position is acceptable.

Fan body

Lighting unit

Ceiling

Joist

Down

The “ “ arrow point to “Up”

Lighting unit

Fan body

Ceiling

Furring

Strap

Joist

Down

The “ “ arrow point to “Down”

Down

6 1/2 (165) Dia.

lamp cover

Ceiling

Ceiling hole

Fig. 7

Ceiling

Suspension

bracket

Joist

>1/8 (3.2)

After finishing the ceiling job, fill gap

between flange and ceiling with caulk

or other sealant to prevent air leakage.

Fig. 8

Lamp cover

Down

Failure to follow the above method may

result in poor performance.

Use other lamp may result in poor performance

or risk of fire.

Down

Fig. 9

LED lamp

INSTALLATION (BETWEEN JOISTS MOUNTING) CONTINUED

The supplied LED lamp is not intended for

other use.

1. Remove the trim ring by pulling down the mounting springs.

(Squeeze mounting spring and pull down carefully.) (Fig. 11)

2. Clean the trim ring. (Don’t put into hot water. Use

non-abrasive kitchen detergent, wipe dry with clean cloth.)

(Fig. 12)

Fig. 12

Gloves Trim ring

Fig. 11

Trim ring

2-Mounting

springs

Gloves

Ceiling

Fig. 10

2-Mounting

springs

Trim ring

①

②

2-Slots

13. Lock the lamp cover.

14. Insert the mounting springs into the slot as shown

in the figure and attach the trim ring to the fan

body. (Fig. 10)

Make sure the lamp cover is locked securely.

Otherwise the lamp cover may drop.

Routine maintenance must be done every year.

Do not immerse motor in water when cleaning.

INSTALLATION (BETWEEN JOISTS MOUNTING) CONTINUED

MAINTENANCE (CLEANING)

4. Remove dust and dirt from fan body using a vacuum

cleaner. (Fig. 13)

(Fig. 14)

1. Remove the trim ring by pulling down mounting springs.

(Squeeze mounting spring and pull down carefully.)

(Fig. 11 of page 9)

2. Unlock the lamp cover. (Fig. 8 of page 8)

3. Replace the LED lamp (GU24 type, 13W). (Fig. 15)

4. Lock the lamp cover.

5. Replace the trim ring.

3. Dry the trim ring after cleaning.

6. Replace the trim ring.

Fig. 13

Vacuum

cleaner

Down

Fig. 14

Gloves

Disconnect power source before working on unit.

This is a GU24 type lamp base and the lamp is fragile and heavy. Please handle with care.

Make sure the temperature of lens and lighting unit has cooled down before maintenance

(cleaning) or replacement of lamp.

Fig. 15

Down

LED lamp

MAINTENANCE (CLEANING) CONTINUED

MAINTENANCE (REPLACEMENT OF LED LAMP)

Autres manuels pour FV-08VRE1

Table des matières

Autres manuels Panasonic Ventilateur

Panasonic

Panasonic FV-NLF46RES Manuel utilisateur

Panasonic

Panasonic RG-C811HA Manuel utilisateur

Panasonic

Panasonic F-302BH Manuel utilisateur

Panasonic

Panasonic FV-30BY1 Manuel utilisateur

Panasonic

Panasonic FV-11VH1 Manuel utilisateur

Panasonic

Panasonic F-50KU1 Manuel utilisateur

Panasonic

Panasonic WhisperLite FV-05VQ5 Manuel utilisateur

Panasonic

Panasonic Whisper Green FV-13VKM2 Manuel utilisateur

Panasonic

Panasonic F-60MZ2 Manuel utilisateur

Panasonic

Panasonic FV-08VKML1 Manuel utilisateur

Panasonic

Panasonic FV-0511VK2 Manuel utilisateur

Panasonic

Panasonic F-M18LY Manuel utilisateur

Panasonic

Panasonic FV-23BWN2H Manuel utilisateur

Panasonic

Panasonic WhisperCeiling FV-15VQ3 Manuel utilisateur

Panasonic

Panasonic Whisper Value-Lite FV-10VSL2 Manuel utilisateur

Panasonic

Panasonic FV-04WS2 Manuel utilisateur

Panasonic

Panasonic FV-07VF1 Manuel utilisateur

Panasonic

Panasonic FV-04VE1 Manuel utilisateur

Panasonic

Panasonic Whisper Green FV-08VKM1 Guide de démarrage rapide

Panasonic

Panasonic FV-07VF1 Manuel utilisateur

Panasonic

Panasonic FV-07VB1 Manuel utilisateur

Panasonic

Panasonic WhisperSense FV-08VQCL6 Manuel utilisateur

Panasonic

Panasonic F-30SMH Manuel utilisateur

Panasonic

Panasonic FV-17CU8 Manuel utilisateur

Manuels Ventilateur populaires d'autres marques

ELTA FANS

ELTA FANS H03VV-F Manuel utilisateur

Hunter

Hunter 20714 Manuel d'instructions

Emerson

Emerson CARRERA VERANDA CF542ORB00 Manuel utilisateur

Hunter

Hunter Caraway Manuel d'instructions

Kompernass

Kompernass KH 1150 Manuel utilisateur

VES

VES FALA100/12V/TR Manuel utilisateur

Vertiv

Vertiv Liebert DCD Manuel utilisateur

Westinghouse

Westinghouse GFP Series Manuel utilisateur

Venmar

Venmar KUBIX HRV PLUS Series Manuel utilisateur

Maico

Maico ECR 31 Manuel utilisateur

Sonnenkonig

Sonnenkonig Dinky Manuel utilisateur

S&P

S&P ECOWATT HXBR Manuel utilisateur

Wider

Wider IMP03369BH Manuel utilisateur

Hinkley

Hinkley HIGHLAND Manuel utilisateur

Broan

Broan 766BN Manuel utilisateur

Premium

Premium PFS16022 Instructions de montage

Litex Industries

Litex Industries E-CGL52CB5C1 Manuel utilisateur

Lindab

Lindab LTDF Manuel utilisateur