Panasonic ES-SA40 Manuel utilisateur
Operating Instructions
(Household) Rechargeable Shaver
Model No. ES‑SA40
Before operating this unit, please read these instructions completely and save
them for future use.
English 2
ES‑SA40_ARA.indb 1 2010/11/15 13:15:35
EN1
Important
Before use
This WET/DRY shaver can be used for wet shaving with shaving lather or
for dry shaving.You can use this watertight shaver in the shower and clean
it in water. The following is the symbol of Wet shaver. The symbol means
that the hand‑held part may be used in a bath or shower.
Treat yourself to wet lather shaves for at least three weeks and notice the
difference. Your Panasonic WET/DRY shaver requires a little time to get
used to because your skin and beard need about a month to adjust to any
new shaving method.
Using the shaver
Caution ‑ The outer foil is very thin and can be damaged if not used
correctly. Check that the foil is not damaged before using the shaver. Do
not use the shaver if the foil etc. is damaged as you will cut your skin.
Charging the shaver
Do not use any charging adaptor other than one specifically designed for
this model (RE7‑67). Plug in the adaptor into a household outlet where
there is no moisture and handle it with dry hands. The shaver may become
warm during use and charging. However, this is not a malfunction. Do not
charge the shaver where it will be exposed to direct sunlight or other heat
sources.
Adequate ambient temperature for charging is 0‑40 °C.
The supply cord cannot be replaced. If the cord is damaged, the appliance
should be scrapped.
Cleaning the shaver
Warning ‑ Remove the shaver from the charging adaptor before cleaning it
to prevent electric shock.
If you clean the shaver with water, do not use salt water or hot water. Do
not soak the shaver in water for a long period of time. Wipe it with a cloth
dampened with soapy water. Do not use thinner, benzine or alcohol.
Storing the shaver
Remove the shaver from the charging adaptor when storing it. This
appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction
ES‑SA40_ARA.indb 1 2010/11/15 13:15:35
EN2
concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the
appliance. Keep these operating instructions in a safe place.
SPECIFICATIONS
Power source: See the name plate on the product.
Motor voltage: 1.2 V DC
Charging time: Approx. 8 hours
This product is intended for household use only.
Parts identification
Protective cap
Outer foil section
Outer foil
Foil frame
Inner blade
Main body
Foil frame release buttons
Switch lock button
0/1 switch
Appliance socket
Trimmer
Trimmer handle
Charging adaptor (RE7‑67)
Charging plug
Charge indicator lamp
Cleaning brush
ES‑SA40_ARA.indb 2 2010/11/15 13:15:35
EN3
Charging
Charge
Perform the following steps to charge the shaver if it seems to lose the speed.
You can fully charge the shaver in 8 hours.
A full charge will supply enough power for approx. 7 shaves of 3 minutes
each.
1
1Turn off the shaver and
insert it in the charging
adaptor as illustrated.
2
2Plug in the adaptor into a
household outlet.
The charge indicator lamp glows and stays on until the shaver is removed
from the charging adaptor.
•
•
ES‑SA40_ARA.indb 3 2010/11/15 13:15:36
EN4
Using the shaver
Shave
90˚
1
1Depress the switch lock
button and slide the 0/1
switch upwards.
2
2Hold the shaver as
illustrated above and
shave.
Start out shaving by applying gentle pressure to your face. Stretch your
skin with your free hand and move the shaver back and forth in the
direction of your beard.You may gently increase the amount of pressure
as your skin becomes accustomed to this shaver. Applying excessive
pressure does not provide a closer shave.
•
Using the trimmer
Slide the trimmer handle up. Place at a right
angle to your skin and move downwards to trim
your sideburns.
ES‑SA40_ARA.indb 4 2010/11/15 13:15:36
EN5
Cleaning
Clean
1. Remove the shaver from the charging
adaptor.
2. Apply some hand soap and some water
to the outer foil.
3. Turn the shaver on.
4. Turn the shaver off after 10‑20 seconds.
5. Remove the outer foil section and turn the
shaver on.
6. Clean the shaver and the outer foil
section with running water.
7. Wipe off any drops of water with a dry
cloth.
8. Dry the outer foil section and the shaver
completely.
9. Attach the outer foil section to the shaver.
ES‑SA40_ARA.indb 5 2010/11/15 13:15:36
EN6
Replacing the outer foil and the inner blade
outer foil once every year
inner blade once every two years
Replacing the outer foil
1. Press the foil frame release buttons and
lift the outer foil section upwards as
illustrated.
2. Gently push the outer foil in the way as
illustrated. Then it will pop up from the foil
frame.
3. The new outer foil should be slightly bent
and pushed in until it is hooked in the foil
frame.
Replacing the inner blade
1. Press the foil frame release buttons and
lift the outer foil section upwards as
illustrated.
2. Remove the inner blade as illustrated.
Do not touch the edges (metal parts) of
the inner blade to prevent injury to your
hand.
3. Insert the inner blade until it clicks as
illustrated.
•
2 3
ES‑SA40_ARA.indb 6 2010/11/15 13:15:37
EN7
Cleaning with the brush
(A)
(B)
1. Clean the inner blade using the short
brush by moving it in direction (A).
Clean the outer foil, the shaver body and
the trimmer using the long brush.
Do not move the short brush in direction
(B) as it will damage the inner blade and
affect its sharpness.
Do not use the short brush to clean the
outer foil.
•
•
Removing the built-in rechargeable battery
Remove the built‑in rechargeable battery before disposing of the shaver.
Please make sure that the battery is disposed of at an officially designated
location if there is one. Do not dismantle or replace the battery so that you
can use the shaver again. This could cause fire or an electric shock. Replace
it at an authorized service center.
Remove the shaver from the charging adaptor when removing the battery.
Perform steps 1to :and lift the battery, and then remove it.
•
•
For environmental protection and recycling of materials
This shaver contains a Nickel‑Metal Hydride battery.
Please make sure that the battery is disposed of at an officially assigned
location, if there is one in your country.
ES‑SA40_ARA.indb 7 2010/11/15 13:15:37
AR1
Panasonic
()
400
ES‑SA40_ARA.indb 1 2010/11/15 13:15:37
AR2
()
ES‑SA40_ARA.indb 2 2010/11/15 13:15:37
Autres manuels pour ES-SA40
4
Table des matières
Langues :
Autres manuels Panasonic Rasoir électrique
Panasonic
Panasonic ER?GB50 Manuel utilisateur
Panasonic
Panasonic ES-WR40 Manuel utilisateur
Panasonic
Panasonic ES-LV50 Manuel utilisateur
Panasonic
Panasonic ES-LC50 Manuel utilisateur
Panasonic
Panasonic ES-RW30-S Manuel utilisateur
Panasonic
Panasonic ES-RT67 Manuel utilisateur
Panasonic
Panasonic ER2403K Manuel utilisateur
Panasonic
Panasonic ES207G Operating Manuel utilisateur
Panasonic
Panasonic ES-ALT4B Manuel utilisateur
Panasonic
Panasonic ES-ST3N Manuel utilisateur
Panasonic
Panasonic ER-GY60 Manuel utilisateur
Panasonic
Panasonic ES6510 Manuel utilisateur
Panasonic
Panasonic ES?LV65 Manuel utilisateur
Panasonic
Panasonic ES-RW30 Manuel utilisateur
Panasonic
Panasonic ES4033 Manuel utilisateur
Panasonic
Panasonic ES-ST37 Manuel utilisateur
Panasonic
Panasonic ES8172-A3 Manuel utilisateur
Panasonic
Panasonic ES6850 Manuel utilisateur
Panasonic
Panasonic ES8066K Operating Manuel utilisateur
Panasonic
Panasonic ES4815 Manuel utilisateur
