Panasonic DMR-EH50GN Manuel utilisateur

ORDER NO.DSD0503043C3

DVD Video Recorder

DMR-EH50GN

Vol.1

Colour

(S).......................Silver Type

of law.

DSD0503043C3

DMR-EH50GN

z0 COVER

z1 Safety precautions

{1_1 General guidelines

1_1_1 Leakage current cold check

1_1_2 Leakage current hot check (See Figure 1

z2 Prevention of Electrostatic Discharge (ESD) to Electrostatic Sensitive (ES) Devices

z3 Precaution of Laser Diode

z4 Handling the Lead-free Solder

{4_1 About lead free solder (PbF)

z5 Each Button

z6 New Feature

{6_1 Quick start function(REC)

z7 Taking out the Disc from RAM-Drive Unit when the Disc cannot be ejected by OPEN/CLOSE

{7_1 Forcible Disc Eject

7_1_1 When the power can be turned off.

7_1_2 When the power can not be turned off.

{7_2 When the Forcible Disc Eject can not be done.

z8 Service Explorer

z9 Self-Diagnosis and Special Mode Setting

{9_1 Self-Diagnosis Functions

{9_2 Special Modes Setting

{9_3 Service Modes

z10 Assembling and Disassembling

{10_1 Disassembly Flow Chart

{10_2 P.C.B. Positions

{10_3 Top Case

{10_4 Front Panel

{10_5 SD Card P.C.B.

{10_6 Digital P.C.B.

{10_7 DVD-RAM Drive

{10_8 HDD

{10_9 LED P.C.B.

{10_10 Power P.C.B.

{10_11 Rear Panel

10_11_1 Fan Motor

{10_12 Front (L) P.C.B.

{10_13 Main P.C.B.

{10_14 Tuner P.C.B. and Nicam Decoder P.C.B.

z11 Service Fixture and Tools

z12 Service Positions

{12_1 Checking and Repairing of Power P.C.B.

{12_2 Checking and Repairing of Digital P.C.B.

{12_3 Checking and Repairing of Main P.C.B.

{12_4 Checking and Repairing of DVD-RAM Drive

{12_5 Checking and Repairing of HDD

z13 Caution after replacing parts

{13_1 After replacing the RAM Drive with new one

{13_2 When the unit does not operate normally after replacing the Timer Microprocessor or

z14 Standard Inspection Specifications after Making Repairs

z15 Voltage and Waveform Chart

{15

1 Power P.C.B.

{15_2 Main P.C.B.

{15_3 Tuner P.C.B.

{15_4 LED P.C.B.

{15_5 P9001 Connector

{15_6 Waveform Chart

z16 Abbreviations

z17 Block Diagram

{17_1 Power Supply Block Diagram

{17_2 Analog Video Block Diagram

{17_3 Analog Audio Block Diagram

{17_4 Timer Block Diagram

z18 Schematic Diagram

{18_1 Interconnection Schematic Diagram

{18_2 Power Supply Schematic Diagram

{18_3 Main Net Section (Main P.C.B. (1/3)) Schematic Diagram (M)

{18_4 A/V I/O Section (Main P.C.B. (2/3)) Schematic Diagram (AI)

{18_5 Timer Section (Main P.C.B. (3/3)) Schematic Diagram (T)

{18_6 Tuner Pack Schematic Diagram

{18_7 Nicam Decoder Schematic Diagram

{18_8 SD Card Schematic Diagram

{18_9 LED Schematic Diagram

z19 Print Circuit Board

{19_1 Power P.C.B.

{19_2 Main P.C.B.

19_2_1 Main P.C.B. (1/4 Section)

19_2_2 Main P.C.B. (2/4 Section)

19_2_3 Main P.C.B. (3/4 Section)

19_2_4 Main P.C.B. (4/4 Section)

19_2_5 Main P.C.B. Address Information

{19_3 Tuner P.C.B., LED P.C.B., Front (L) P.C.B.

{19_4 Nicam Decoder P.C.B.

{19_5 SD Card P.C.B.

z20 Exploded Views

{20_1 Casing Parts & Mechanism Section

{20_2 Packing & Accessories Section

z21 Replacement Parts List

z22 Schematic Dia

ram for

rintin

with A4

1 Safety precautions

1.1 General guidelines

1. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been

overheated or damaged by the short circuit.

2. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are

properly installed.

3. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock

hazards.

1.1.1 Leakage current cold check

1. Unplug the AC cord and connect a jumper between the two prongs on the plug.

2. Measure the resistance value, with an ohmmeter, between the jumpered AC plug and each exposed metallic

cabinet part on the equipment such as screwheads, connectors, control shafts, etc. When the exposed metallic

part has a return path to the chassis, the reading should be between 1MΩand 5.2MΩ.

When the exposed metal does not have a return path to the chassis, the reading must be .

Figure 1

1.1.2 Leakage current hot check

(See Figure 1 .)

1. Plug the AC cord directly into the AC outlet. Do not use an isolation transformer for this check.

2. Connect a 1.5kΩ, 10 watts resistor, in parallel with a 0.15µF capacitors, between each exposed metallic part on

the set and a good earth ground such as a water pipe, as shown in Figure 1 .

3. Use an AC voltmeter, with 1000 ohms/volt or more sensitivity, to measure the potential across the resistor.

4. Check each exposed metallic part, and measure the voltage at each point.

5. Reverse the AC plug in the AC outlet and repeat each of the above measurements.

6. The potential at any point should not exceed 0.75 volts RMS. A leakage current tester (Simpson Model 229 or

equivalent) may be used to make the hot checks, leakage current must not exceed 1/2 milliampere. In case a

measurement is outside of the limits specified, there is a possibility of a shock hazard, and the equipment should

be repaired and rechecked before it is returned to the customer.

2 Prevention of Electrostatic

Discharge (ESD) to Electrostatic

Sensitive (ES) Devices

Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are

called Electrostatic Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect

transistor-sand semiconductor "chip" components. The following techniques should be used to help reduce the

incidence of component damage caused by electrostatic discharge (ESD).

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any

ESD on your body by touching a known earth ground. Alternatively, obtain and wear a commercially available

discharging ESD wrist strap, which should be removed for potential shock reasons prior to applying power to the

unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such

as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an anti-static solder removal device. Some solder removal devices not classified as "anti-static (ESD

protected)" can generate electrical charge sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to

install it. (Most replacement ES devices are packaged with leads electrically shorted together by conductive foam,

aluminum foil or comparable conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the

protective material to the chassis or circuit assembly into which the device will be installed.

Caution

Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise hamless motion such as

the brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static

electricity sufficient to damage an ES device).

3PrecautionofLaserDiode

4 Handling the Lead-free Solder

4.1 About lead free solder (PbF)

Distinction of PbF P.C.B.:

P.C.B.s (manufactured) using lead free solder will have a PbF stamp on the P.C.B.

Caution:

zPb free solder has a higher melting point than standard solder; Typically the melting point is 50 - 70°F (30 - 40°C)

higher. Please use a high temperature soldering iron. In case of the soldering iron with temperature control, please

set it to 700 ± 20°F (370 ± 10°C).

zPb free solder will tend to splash when heated too high (about 1100°F/600°C).

zWhen soldering or unsoldering, please completely remove all of the solder on the pins or solder area, and be sure

to heat the soldering points with the Pb free solder until it melts enough.

5 Each Button

6 New Feature

6.1 Quick start function(REC)

1. General

A few seconds after tuning on the unit,you can start recording to DVD-RAM,HDD.

You can switch the operation of this function (ON/OFF) on the menu screen. .

2. Quick start(REC) principle

In the power-off at Quick start, only power supplies for video IC,tuner and storage media are cut off.

When the REC button is pushed a few second after the power button is pushed, Audio and Video data

are stored in

DDR SDRAM before a storage media(DVD-RAM or HDD) preparation.

*Preparation time →DVD-RAM: Fabout 8seconds

HDD: about 18seconds

After a storage media(DVD-RAM or HDD) preparation,Audio and Video data are transfer from DDR

SDRAM to the storage media.

Autres manuels Panasonic DVR

Panasonic

Panasonic DMR-T3030 Manuel utilisateur

Panasonic

Panasonic DMR-E100H Manuel utilisateur

Panasonic

Panasonic WJ-ND300A/10000V Manuel utilisateur

Panasonic

Panasonic PI-HRA081A Manuel utilisateur

Panasonic

Panasonic Diga DMR-E65 Manuel utilisateur

Panasonic

Panasonic WJRT416 - 16CH DIGITAL RECORDER Manuel utilisateur

Panasonic

Panasonic WJ-ND300A Manuel utilisateur

Panasonic

Panasonic DMR-E85HEE Manuel utilisateur

Panasonic

Panasonic WJHD500A - Digital Disk Recorder Manuel utilisateur

Panasonic

Panasonic DMR-E85HP Manuel utilisateur

Panasonic

Panasonic DMR-T3040 Manuel utilisateur

Panasonic

Panasonic WJHD309 - DIGITAL DISK RECORDER Manuel utilisateur

Panasonic

Panasonic BB-HNP17A Instructions de montage

Panasonic

Panasonic LQ-MD800 Manuel utilisateur

Panasonic

Panasonic DMRE500H - DVD RECORDER DECK Manuel utilisateur

Panasonic

Panasonic DMRE80HP Instructions de construction

Panasonic

Panasonic WJ-ND400/1000 Manuel utilisateur

Panasonic

Panasonic WJ-HD300A Manuel de référence

Panasonic

Panasonic Diga DMR-E60 Manuel utilisateur

Panasonic

Panasonic WJRT416 - 16CH DIGITAL RECORDER Manuel utilisateur

Panasonic

Panasonic WJHD220 - DIGITAL DISK RECORDER Manuel utilisateur

Panasonic

Panasonic Diga DMR-E95H Manuel utilisateur

Panasonic

Panasonic PocketProDVR MDVR-12 Manuel utilisateur

Panasonic

Panasonic DMRE500H - DVD RECORDER DECK Manuel utilisateur

Manuels DVR populaires d'autres marques

FLIR

FLIR M3100E Series Manuel utilisateur

VTRACKPRO

VTRACKPRO FPRO300 Manuel utilisateur

Swann

Swann NVR-7085 models Manuel utilisateur

XtendLan

XtendLan DVR-1670C Manuel utilisateur

urmet domus

urmet domus 1093/004AHD Manuel utilisateur

Holux

Holux M1 Manuel utilisateur

CMOS DOTCOM

CMOS DOTCOM ANX-1670 Manuel utilisateur

Whistler

Whistler D16VRS Manuel utilisateur

Defender Security

Defender Security 82-20235 Manuel utilisateur

MISUMI

MISUMI MP-WF100M Manuel utilisateur

Speco

Speco D8HU Manuel utilisateur

UST

UST DDR-E04AA Instructions d'utilisation

Consolidated

Consolidated Digital Video Recorder Manuel utilisateur

Mace

Mace DVR0404RW Guide de démarrage rapide

RCA

RCA RTD315W Manuel utilisateur

FSM

FSM Colibri Grande PRO Manuel utilisateur

Hauppauge

Hauppauge HD PVR 2 Manuel utilisateur

Identivision

Identivision ICR-PH161i PIONEER Manuel utilisateur