Panasonic EY74A2 Manuel utilisateur

Unauthorized copying and distribution is a violation

of law.

ORDER NO. PTD1507X58CE

Cordless Drill & Driver

Model No. EY74A2

Europe

Oceania

TABLE OF CONTENTS

PAGE PAGE

1 Warning -------------------------------------------------------------- 2

2 Specifications ----------------------------------------------------- 2

3 Troubleshooting Guide ----------------------------------------- 3

4 Disassembly and Assembly Instructions ---------------- 7

5 Wiring Connection Diagram ---------------------------------13

6 Schematic Diagram ---------------------------------------------13

7 Exploded View and Replacement Parts List -----------14

1Warning

Caution:

• Pb free solder has a higher melting point that standard solder; Typically the melting point is 50 - 70 °F (30 - 40 °C) higher.

Please use a soldering iron with temperature control and adjust it to 750 ± 20 °F (400 ± 10 °C). In case of using high temperature

soldering iron, please be careful not to heat too long.

• Pb free solder will tend to splash when heated too high (about 1100°F / 600 °C).

2 Specifications

3 Troubleshooting Guide

3.1. Troubleshooting Guide

3.2. Trial Operation (after checking Troubleshooting Guide).

3.2.1. Assembly

• Confirm if there is no gap between housing A, B and C by pinching lead wires.

• There is no dust or deformation on battery terminals.

3.2.2. Operation

• Check whether the tool operates properly in both the forward and reveres directions.

• Press the light button on the operation panel to confirm that the LED lights up.

• Check whether the tool speed increases continuously as the trigger is gradually engaged.

• Rotate the clutch handle and check whether the clutch switches properly.

• Check if the rotation speed is normal rated value.

High: 1580/min (rpm) at 18V, 1350/min (rpm) at 14.4V

Low: 470/min (rpm) at 18V, 400/min (rpm) at 14.4V

• Pull the trigger all the way back and check whether the tool stops rotating immediately when it is released.

• Set the clutch handle to the [ ] mark and check whether the tool rotates without any clutch operation.

• Operate (rotate) the keyless chuck and check whether the chuck's three jaws move smoothly.

3.2.3. Integrity

• With the switch activated, shake the tool back and forth and up and down and verify that its sound does not change excessively.

• Check for the presence of any dirt or foreign matter from the repair process on the outside of the tool.

4 Disassembly and Assembly Instructions

* To reduce the risk of injury, always remove battery pack before removing/installing the tool.

* To assemble the tool, start with 4-9 and proceed to 4-1.

4.1. Removing the Plate Hook.

4.2. Removing the Keyless Chuck.

1. Remove the M4-14 screw.

2. Remove the plate hook.

1. Use a screwdriver to turn the chuck fastening screw inside the chuck

clockwise direction, and remove the screw.

* in case of the chuck does not come loose; NOTE:

If the chuck fastening screw will not come loose, insert the allen wrench

into the chuck and lightly tap in the clockwise direction to tighten the

chuck, and then loosen the chuck fastening screw.

2. Insert the allen wrench into the chuck, and turn counterclockwise

direction with holding the unit by the vise to remove the chuck.

NOTE:

If the chuck is broken, use a allen wrench and turn counterclockwise

direction to remove the chuck.

4.3. Removing the Housing.

4.4. Removing the Interior Components.

1. Remove nine screws.

2. Remove housing B.

3. Remove the F/R selector handle.

4. Remove the operation panel.

5. Remove the square nut.

1. Remove the heat resistant tape and remove the interior components

from the housing A.

* Precautions when securing LED assembly in place using the resistant

tape.

Attach the heat resistant tape at the location shown in the figure below.

2. Remove the clutch handle, H/L change handle and click spring from

the gear block assembly.

4.5. Removing the Switch Assembly, LED Assembly and Battery Terminal.

4.6. Removing the Gear Case Assembly from the Module Assembly.

1. Remove the 2-pin connector.

2. Remove the 6-pin connector.

3. Pull the faston terminal directly

out from the switch assembly.

* Exercise care not to bend the ter-

minal fitting.

4. Remove the lead wires from the

battery terminal.

Connecting and disconnecting the connector

* Precautions when attaching the connectors

Holding the motor assembly, remove the entire motor mounting plate,

including the gear box assembly from the motor assembly.

4.7. Removing the Gear Case Assembly.

1. Rotate the motor mounting plate to the

left and remove it from the gear case.

2. Remove the thrust plate, planet gear

B, ring gear B, carrier B, planet gear A,

carrier A, and the ring gear A (in that

order).

3. Remove 4 screws.

4. Remove the gear case, stopper, thrust

plate, planet gear, ring gear, carrier, steel

balls, pin, cushion plate, lock plate, lock

ring, thrust plate, wave washer and

thrust plate (in that order).

5. Insert the jaws of snap ring into two

holes on the C-ring. Open the jaws and

lift up on the ring to remove it.

* The C-ring cannot be reused after

being repaired or otherwise adjusted.

6. Remove the driving shaft, thrust plate,

steel balls, thrust plate, adjust screw,

clutch spring and thrust plate from the

clutch case.

* Assembly precautions

1. Exercise care when attaching the lock ring, ring gear, stopper, and ring

gear A to align them in the proper orientation (as shown in the above figure).

2. When installing the gear case to the clutch case, be sure to align the pro-

truding ribs on the clutch case with the recessed ribs on the gear case.

3. When installing the motor mounting plate to the gear case, align and

engage the two protruded sections on motor mounting plate with the two

notches on the gear case, then turn the motor mounting plate clockwise until

a clicking sound is produced to ensure secure mounting.

4. When installing the adjusting screw, make sure that the narrow protrusion

is on the right and flush with the clutch case surface.

5. Precautions when applying the grease (ALVANIA).

Autres manuels pour EY74A2

Table des matières

Autres manuels Panasonic Percer

Panasonic

Panasonic EY6405-X8 Manuel utilisateur

Panasonic

Panasonic EY6450 - DRILL AND DRIVER Manuel utilisateur

Panasonic

Panasonic EY7441 Manuel utilisateur

Panasonic

Panasonic EY7430 Manuel utilisateur

Panasonic

Panasonic EY6405 - CORDLES DRILL&DRIVER Manuel utilisateur

Panasonic

Panasonic EY6230 - CORDLES DRILL&DRIVER Manuel utilisateur

Panasonic

Panasonic EY 6220 Manuel utilisateur

Panasonic

Panasonic EY6950 - 18V HAM. DRILL&DRIVE Manuel utilisateur

Panasonic

Panasonic EY7542 - CORDLESS IMPACT WRENCH Manuel utilisateur

Panasonic

Panasonic EYFEA1N2S Manuel utilisateur

Panasonic

Panasonic EY6432NQKW Manuel utilisateur

Panasonic

Panasonic EY7460 - DRILL DRIVER 21.6V Manuel utilisateur

Panasonic

Panasonic EY7441 Manuel utilisateur

Panasonic

Panasonic EY6405 - CORDLES DRILL&DRIVER Manuel utilisateur

Panasonic

Panasonic EY7411 - CORDLESS DRILL & DRIVER Manuel utilisateur

Panasonic

Panasonic EY6930 - HAMMER DRILL Manuel utilisateur

Panasonic

Panasonic EY6931 - 15.6V HAMMER DRILL Manuel utilisateur

Panasonic

Panasonic EY6903 Manuel utilisateur

Panasonic

Panasonic EY6780 Manuel utilisateur

Panasonic

Panasonic EY6903 Manuel utilisateur

Panasonic

Panasonic EY7542LN2L Manuel utilisateur

Panasonic

Panasonic EY7441 Manuel utilisateur

Panasonic

Panasonic EY6450 - DRILL AND DRIVER Manuel utilisateur

Panasonic

Panasonic EY7442 Manuel utilisateur

Manuels Percer populaires d'autres marques

Makita

Makita BDF456 Manuel utilisateur

Black & Decker

Black & Decker LDX220 Manuel utilisateur

Hitachi

Hitachi DH 40MA Manuel utilisateur

Challenge

Challenge JO Manuel de référence technique

Makita

Makita LXFD01 Manuel utilisateur

Festool

Festool T18+3 Manuel utilisateur

Milwaukee

Milwaukee M12 FPDX-202X Manuel utilisateur

EINHELL

EINHELL TE-RH 32 E Manuel utilisateur

Makita

Makita DHP484 Manuel utilisateur

Makita

Makita FD05 Manuel utilisateur

Bosch

Bosch PSB 530 RA Manuel utilisateur

Maximum

Maximum 054-1359-4 Manuel utilisateur

Makita

Makita HP332D Manuel utilisateur

Raider

Raider RDP-HD31H Manuel utilisateur

Bort

Bort BPM-1400x2 Manuel utilisateur

Black & Decker

Black & Decker 7266 Manuel utilisateur

KENT USA

KENT USA TRD1230 Manuel utilisateur

Bosch

Bosch GSB 19-2 RE Manuel utilisateur