Panasonic SDR-S45EF Manuel utilisateur

Unauthorized copying and distribution is a violation

of law.

ORDER NO.VM1004027CE

SD Video Camera

Model No. SDR-S45EG

SDR-S45EF

SDR-S45EC

SDR-S45EP

SDR-S45EB

SDR-S45EE

SDR-S45GC

SDR-S45GA

SDR-S45GN

SDR-S45PU

SDR-S45PR

VOL.1

Colour

(S)........Silver Type

TABLE OF CONTENTS PAGE PAGE

1 Safety Precautions -----------------------------------------------3

1.1. General Guidelines ----------------------------------------3

2Warning--------------------------------------------------------------4

2.1. Prevention of Electrostatic Discharge (ESD)

to Electrostatic Sensitive (ES) Devices---------------4

2.2. Service caution based on legal restrictions----------5

2.3. Caution for AC Cord (For EB/GC/GA) ----------------6

2.4. How to Replace the Lithium Battery

(PROCEDURE)---------------------------------------------7

3 Service Navigation------------------------------------------------9

3.1. Service Information----------------------------------------9

3.2. How to Define the Model Suffix (NTSC or PAL

model)-------------------------------------------------------10

4 Specifications---------------------------------------------------- 11

5 Location of Controls and Components------------------12

6 Service Mode-----------------------------------------------------15

6.1. Lock Search History Indication -----------------------16

6.2. Power ON Self Check Result Display---------------16

6.3. Lock Search History Clear-----------------------------17

7 Service Fixture & Tools ---------------------------------------18

7.1. Service Tools and Equipment-------------------------18

8 Disassembly and Assembly Instructions---------------19

8.1. Disassembly Flow Chart--------------------------------19

8.2. P.C.B. Layout----------------------------------------------19

8.3. Disassembly Procedures-------------------------------20

8.4. Disassembly Procedures of Camera Lens

Unit-----------------------------------------------------------27

9 Measurements and Adjustments --------------------------29

9.1. EEPROM Data for spare parts of the MAIN

P.C.B.--------------------------------------------------------29

9.2. Service Positions-----------------------------------------29

9.3. Location for Connectors of the Main P.C.B. -------31

9.4. Electrical Adjustment------------------------------------32

10 Maintenance ------------------------------------------------------34

10.1. Cleaning Lens and LCD Panel -----------------------34

11 Factory Setting---------------------------------------------------35

11.1. How to turn on the factory setting? ------------------35

11.2. What is the factory settings?--------------------------35

1 Safety Precautions

1.1. General Guidelines

1. IMPORTANT SAFETY NOTICE

There are special components used in this equipment which are important for safety. These parts are marked by in the

Schematic Diagrams, Circuit Board Layout, Exploded Views and Replacement Parts List. It is essential that these critical parts

should be replaced with manufacturer’s specified parts to prevent X-RADIATION, shock fire, or other hazards. Do not modify

the original design without permission of manufacturer.

2. An Isolation Transformer should always be used during the servicing of AC Adaptor whose chassis is not isolated from the AC

power line. Use a transformer of adequate power rating as this protects the technician from accidents resulting in personal

injury from electrical shocks. It will also protect AC Adaptor from being damaged by accidental shorting that may occur during

servicing.

3. When servicing, observe the original lead dress. If a short circuit is found, replace all parts which have been overheated or

damaged by the short circuit.

4. After servicing, see to it that all the protective devices such as insulation barriers, insulation papers shields are properly

installed.

5. After servicing, make the following leakage current checks to prevent the customer from being exposed to shock hazards.

1.1.1. Leakage Current Cold Check

1. Unplug the AC cord and connect a jumper between the two prongs on the plug.

2. Measure the resistance value, with an ohmmeter, between the jumpered AC plug and each exposed metallic cabinet part on

the equipment such as screwheads, connectors, control shafts, etc. When the exposed metallic part has a return path to the

chassis, the reading should be between 1MΩand 5.2MΩ. When the exposed metal does not have a return path to the chas-

sis, the reading must be infinity.

1.1.2. Leakage current hot check (See Figure 1)

1. Plug the AC cord directly into the AC outlet. Do not use

an isolation transformer for this check.

2. Connect “A” to exposed metallic part on the set. And con-

nect “B” to a good earth ground, as shown in Figure 1.

3. Use an AC voltmeter, with 1 kΩ/V or more sensitivity, to

measure the potential across the resistor.

4. Check each exposed metallic part, and measure the volt-

age at each point.

5. Reverse the AC plug in the AC outlet and repeat each of

the above measurements.

6. The potential at any point should not exceed 0.25 V RMS.

A leakage current tester (Simpson Model 229 or equiva-

lent) may be used to make the hot checks, leakage cur-

rent must not exceed 1/2 mA. In case a measurement is

outside of the limits specified, there is a possibility of a

shock hazard, and the equipment should be repaired and

rechecked before it is returned to the customer.

Figure 1

2Warning

2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatic Sensitive

(ES) Devices

Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec-

trostatic Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and semi-

conductor “chip” components. The following techniques should be used to help reduce the incidence of component damage caused

by electrostatic discharge (ESD).

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your

body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,

which should be removed for potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alumi-

num foil, to prevent electrostatic charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an antistatic solder removal device. Some solder removal devices not classified as “antistatic (ESD protected)” can

generate electrical charge sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most

replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compara-

ble conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material

to the chassis or circuit assembly into which the device will be installed.

CAUTION:

Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the

brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) suf-

ficient to damage an ES device).

2.2. Service caution based on legal restrictions

2.2.1. General description about Lead Free Solder (PbF)

The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this

equipment in considering the globally environmental conservation.

The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin

(Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30 degrees C (86°F) more than that

of the normal solder.

Definition of PCB Lead Free Solder being used

Service caution for repair work using Lead Free Solder (PbF)

• The lead free solder has to be used when repairing the equipment for which the lead free solder is used.

(Definition: The letter of “PbF” is printed on the PCB using the lead free solder.)

• To put lead free solder, it should be well molten and mixed with the original lead free solder.

• Remove the remaining lead free solder on the PCB cleanly for soldering of the new IC.

• Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt the

lead free solder.

• Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 350±30 degrees

C (662±86°F).

Recommended Lead Free Solder (Service Parts Route.)

• The following 3 types of lead free solder are available through the service parts route.

RFKZ03D01KS-----------(0.3mm 100g Reel)

RFKZ06D01KS-----------(0.6mm 100g Reel)

RFKZ10D01KS-----------(1.0mm 100g Reel)

Note

* Ingredient: tin (Sn), 96.5%, silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%

The letter of “PbF” is printed either foil side or components side on the PCB using the lead free solder.

(See right figure)

2.3. Caution for AC Cord

(For EB/GC/GA)

2.3.1. Information for your safety

IMPORTANT

Your attention is drawn to the fact that recording of pre-

recorded tapes or discs or other published or broadcast

material may infringe copyright laws.

WARNING

To reduce the risk of fire or shock hazard, do not expose

this equipment to rain or moisture.

CAUTION

To reduce the risk of fire or shock hazard and annoying

interference, use the recommended accessories only.

FOR YOUR SAFETY

DO NOT REMOVE THE OUTER COVER

To prevent electric shock, do not remove the cover. No user

serviceable parts inside. Refer servicing to qualified service

personnel.

2.3.2. Caution for AC mains lead

For your safety, please read the following text carefully.

This appliance is supplied with a moulded three-pin mains plug

for your safety and convenience.

A 5-ampere fuse is fitted in this plug.

Should the fuse need to be replaced please ensure that the

replacement fuse has a rating of 5 amperes and it is approved

by ASTA or BSI to BS1362

Check for the ASTA mark or the BSI mark on the body of the

fuse.

If the plug contains a removable fuse cover you must ensure

that it is refitted when the fuse is replaced.

If you lose the fuse cover, the plug must not be used until a

replacement cover is obtained.

A replacement fuse cover can be purchased from your local

Panasonic Dealer.

If the fitted moulded plug is unsuitable for the socket outlet in

your home then the fuse should be removed and the plug cut

off and disposed of safety.

There is a danger of severe electrical shock if the cut off plug is

inserted into any 13-ampere socket.

If a new plug is to be fitted please observe the wiring code as

shown below.

If in any doubt, please consult a qualified electrician.

2.3.2.1. Important

The wires in this mains lead are coloured in accordance with

the following code:

As the colours of the wires in the mains lead of this appliance

may not correspond with the coloured markings identifying the

terminals in your plug, proceed as follows:

The wire which is coloured BLUE must be connected to the ter-

minal in the plug which is marked with the letter N or coloured

BLACK.

The wire which is coloured BROWN must be connected to the

terminal in the plug which is marked with the letter L or coloured

RED.

Under no circumstances should either of these wires be con-

nected to the earth terminal of the three pin plug, marked with

the letter E or the Earth Symbol.

2.3.2.2. Before use

remove the Connector Cover as follows.

2.3.2.3. How to replace the Fuse

1. Remove the Fuse Cover with a screwdriver.

2. Replace the fuse and attach the Fuse cover.

Blue Neutral

Brown Live

2.4. How to Replace the Lithium Battery (PROCEDURE)

1. Remove the Monitor P.C.B. (Refer to Disassembly Procedures.)

2. Unsolder the Lithium Battery “ML-614S/DN” and then replace the new one. (See Fig. B1.)

Fig. B1

Note:

The lithium battery is a critical component.

(Type No.: ML-614S/DN Manufactured by Energy Company, Panasonic Corporation)

It must never be subjected to excessive heat or discharge.

It must therefore only be fitted in equipment designed specifically for its use.

Replacement batteries must be of the same type and manufacture.

They must be fitted in the same manner and location as the original battery, with the correct polarity contacts observed.

Do not attempt to re-charge the old battery or re-use it for any other purpose.

It should be disposed of in waste products destined for burial rather than incineration.

Note:

Above caution is applicable for a battery pack which is for SDR-S45 series, as well.

3 Service Navigation

3.1. Service Information

This service manual contains technical information which will allow service personnel's to understand and service this model.

Please place orders using the parts list and not the drawing reference numbers.

If the circuit is changed or modified, this information will be followed by supplement service manual to be filed with original service

manual.

Notes 1:

1) This service manual does not contain the following information, because of the impossibility of servicing at component level.

1. Schematic Diagram, Block Diagram and P.C.B. layout of Main P.C.B.

2. Parts List for individual parts of Main P.C.B.

2) The following category are recycle module part. Please send them to Central Repair Center.

*Main P.C.B. (VEP03H83DP : SDR-S45EG/EF/EC/EP/EB)

(VEP03H83DQ : SDR-S45EE/GC/GA/GN)

(VEP03H83DN : SDR-S45PU/PR)

3.2. How to Define the Model Suffix (NTSC or PAL model)

There are three kinds of SDR-S45, regardless of the colours.

• a) SDR-S45EG/EF/EC/EP/EB/GN

• b) SDR-S45EE

• c) SDR-S45GC/GA/PU/PR

What is the difference is that the ”INITIAL SETTINGS” data which is stored in Flash ROM mounted on Main P.C.B.

3.2.1. Defining methods

To define the model suffix to be serviced, refer to the nameplate which is putted on the bottom side of the Unit.

Note:

After replacing the MAIN P.C.B., be sure to achieve adjustment.

The adjustment instruction is available at “software download” on the “Support Information from NWBG/VDBG-AVC” web-site in

“TSN system”, together with Maintenance software.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Panasonic Appareil photo numérique

Panasonic

Panasonic Lumix DMC-GF7W Caractéristiques techniques

Panasonic

Panasonic Lumix DMC-SZ5 Caractéristiques techniques

Panasonic

Panasonic DMC FZ28K - Lumix Digital Camera Mode d’emploi

Panasonic

Panasonic LUMIX DMC-FH20 Caractéristiques techniques

Panasonic

Panasonic DMC-FP8S - Lumix Digital Camera Manuel utilisateur

Panasonic

Panasonic D-SNAP SV-AS30 Manuel utilisateur

Panasonic

Panasonic LUMIX DMC-LX100GN Caractéristiques techniques

Panasonic

Panasonic Lumix DMC-G2K Manuel utilisateur

Panasonic

Panasonic DMC-ZS25K Manuel utilisateur

Panasonic

Panasonic DMC-L1K - Lumix Digital Camera SLR Manuel utilisateur

Panasonic

Panasonic Lumix DC-GH5KBODY Caractéristiques techniques

Panasonic

Panasonic Lumix DMC-FZ48 Caractéristiques techniques

Panasonic

Panasonic Lumix DC-ZS80D Manuel utilisateur

Panasonic

Panasonic GP-VD150 Manuel utilisateur

Panasonic

Panasonic Lumix DMC-ZS8 Instructions d'installation et d'entretien

Panasonic

Panasonic AK-HC910L Manuel utilisateur

Panasonic

Panasonic Lumix DMC-TS5D Manuel utilisateur

Panasonic

Panasonic Lumix DMC-SZ1 Instructions d'installation et d'entretien

Panasonic

Panasonic LUMIX DMC-FX75 Caractéristiques techniques

Panasonic

Panasonic Lumix DMC-LS80 Manuel utilisateur

Panasonic

Panasonic Lumix DMC-FS9EB Manuel utilisateur

Panasonic

Panasonic Lumix DMC-FP3P Manuel utilisateur

Panasonic

Panasonic DMC-LX7K Manuel utilisateur

Panasonic

Panasonic S-S50 Manuel utilisateur

Manuels Appareil photo numérique populaires d'autres marques

Mercury

Mercury 350K Manuel utilisateur

Pentax

Pentax Optio LS 465 Manuel utilisateur

Sanyo

Sanyo VPC-S1085 Manuel utilisateur

GE SMART A1255 Manuel utilisateur

Point Grey

Point Grey Gazelle Manuel utilisateur

Nikon

Nikon COOLPIX A Manuel utilisateur

Pentax

Pentax P-5 Manuel utilisateur

BlazeVideo

BlazeVideo A280 Manuel utilisateur

Sony

Sony MCA-20 Manuel utilisateur

Sony

Sony Alpha DSLR-A290 Manuel utilisateur

ATIK Cameras

ATIK Cameras One Manuel utilisateur

CohuHD Costar

CohuHD Costar 3930 Series Manuel utilisateur

Leica

Leica M10-R Manuel utilisateur

FujiFilm

FujiFilm FinePix A700 Manuel utilisateur

Lorex

Lorex LNZ81P25 Series Manuel utilisateur

GE J1470S Manuel utilisateur

Sony

Sony A6700 Guide de l'utilisateur

Canon

Canon EOS ELAN7 Manuel utilisateur