Panasonic SDR-H18P Manuel utilisateur

rights reserved. Unauthorized copying and

distribution is a violation of law.

SDR-H18P

SDR-H20P

SDR-H18PC

SDR-H20PC

Vol. 1

Colours

(S)...................Silver Type

SD Card/Hard Disk Video Camera

ORDER NO. MKE0702300CE

B27

1 Safety Precautions 3

1.1. General Guidelines 3

2 Warning 4

2.1. Prevention of Electro Static Discharge (ESD) to

Electrostatically Sensitive (ES) Devices 4

2.2. How to Recycle the Lithium Battery 4

2.3. How to Replace the Lithium Battery 5

3 Service Navigation 6

3.1. Introduction 6

3.2. About Lead Free Solder (PbF) 6

3.3. Precautions for Handling HDD 7

3.4. Formatting HDD 11

4 Specifications 12

5 Service Mode 13

5.1. Error Display 13

5.2. Service Menu 13

5.3. About Default Setting 18

6 Service Fixture & Tools 19

6.1. Service Fixture and Tools 19

6.2. Service Position 20

6.3. Removal/Installation of F.P.C. From Non ZIF (Zero

Insertion Force) Connector 23

6.4. EEPROM Data 24

6.5. Special Note 25

6.6. Model No. Identification Mark 25

7 Disassembly and Assembly Instructions 26

7.1. Disassembly Flow Chart 26

7.2. P.C.B. Layout 26

7.3. Disassembly Procedures 27

8 Measurements and Adjustments 33

8.1. Electrical Adjustment 33

9 Maintenance 36

9.1. Cleaning Lens and LCD Panel 36

10 Troubleshooting 37

11 Voltage Chart of Connectors on Main P.C.B. 48

12 Block Diagrams 49

13 Schematic Diagrams 51

13.1. SCHEMATIC DIAGRAM & CIRCUIT BOARD LAYOUT

NOTES 51

13.2. FRONT SCHEMATIC DIAGRAM 52

13.3. LCD BACKLIGHT SCHEMATIC DIAGRAM 53

13.4. HDD RELAY SCHEMATIC DIAGRAM 54

13.5. SIDE R / LCD OPEN SWITCH SCHEMATIC DIAGRAM

13.6. CCD / REAR CASE / SHAFT FPC / HDD RELAY FPC

SCHEMATIC DIAGRAMS 56

13.7. SIDE L / OPERATION / TOP OPERATION SCHEMATIC

DIAGRAMS 57

13.8. INTERCONNECTION SCHEMATIC DIAGRAM 58

14 Printed Circuit Board 59

14.1. FRONT P.C.B. 59

14.2. HDD RELAY P.C.B. 60

14.3. LCD BACKLIGHT P.C.B. 61

14.4. SIDE R P.C.B. 62

14.5. OPEN SWITCH P.C.B. 63

15 Exploded View 65

15.1. MAIN PARTS SECTION 65

15.2. FRONT HOOD AND FRONT P.C.B. SECTION 66

15.3. SIDE R OPERATION AND LCD SECTION 67

15.4. CCD AND LENS SECTION 68

15.5. PACKING PARTS AND ACCESSORIES SECTION 69

16 Replacement Parts Lists 70

16.1. REPLACEMENT NOTES 70

16.2. MECHANICAL REPLACEMENT PARTS LIST 71

16.3. ELECTRICAL REPLACEMENT PARTS LIST 71

CONTENTS

Page Page

SDR-H18P / SDR-H20P / SDR-H18PC / SDR-H20PC

1 Safety Precautions

1.1. General Guidelines

1. IMPORTANT SAFETY NOTICE

There are special components used in this equipment

which are important for safety. These parts are marked by

in the Schematic Diagrams, Circuit Board Layout,

Exploded Views and Replacement Parts List. It is essential

that these critical parts should be replaced with

manufacturer’s specified parts to prevent shock, fire, or

other hazards. Do not modify the original design without

permission of manufacturer.

2. An Isolation Transformer should always be used during the

servicing of AC Adaptor whose chassis is not isolated from

the AC power line. Use a transformer of adequate power

rating as this protects the technician from accidents

resulting in personal injury from electrical shocks. It will also

protect AC Adaptor from being damaged by accidental

shorting that may occur during servicing.

3. When servicing, observe the original lead dress. If a short

circuit is found, replace all parts which have been

overheated or damaged by the short circuit.

4. After servicing, see to it that all the protective devices such

as insulation barriers, insulation papers shields are properly

installed.

5. After servicing, make the following leakage current checks

to prevent the customer from being exposed to shock

hazards.

SDR-H18P / SDR-H20P / SDR-H18PC / SDR-H20PC

2 Warning

2.1. Prevention of Electro Static Discharge (ESD) to Electrostatically

Sensitive (ES) Devices

Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called

Electrostatically Sensitive (ES) Devices. Examples of typical ES devices are integrated circuits and some field-effect transistors and

semiconductor "chip" components. The following techniques should be used to help reduce the incidence of component damage

caused by electro static discharge (ESD).

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your

body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,

which should be removed for potential shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as

aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.

4. Use only an antistatic solder removal device. Some solder removal devices not classified as "antistatic (ESD protected)" can

generate electrical charge sufficient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.

6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most

replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable

conductive material).

7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material

to the chassis or circuit assembly into which the device will be installed.

CAUTION :

Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the

brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD)

sufficient to damage an ES device).

2.2. How to Recycle the Lithium Battery

SDR-H18P / SDR-H20P / SDR-H18PC / SDR-H20PC

2.3. How to Replace the Lithium Battery

1. Remove the Side R P.C.B.. (Refer to Disassembly Procedures.)

2. Unsolder the Lithium Battery “ML-621S/F9D” and then replace the new one.

NOTE:

This Lithium battery is a critical component. (Type No.: ML-621S/F9D Manufactured by Panasonic.)

It must never be subjected to excessive heat or discharge.

It must therefore only be fitted in equipment designed specifically for its use.

Replacement batteries must be of the same type and manufacture.

They must be fitted in the same manner and location as the original battery, with the correct polarity contacts observed.

Do not attempt to re-charge the old battery or re-use it for any other purpose.

It should be disposed of in waste products destined for burial rather than incineration.

SDR-H18P / SDR-H20P / SDR-H18PC / SDR-H20PC

3 Service Navigation

3.1. Introduction

This service manual contains technical information which will allow service personnel´s to understand and service this model.

Please place orders using the parts list and not the drawing reference numbers.

If the circuit is changed or modified, this information will be followed by supplement service manual to be filed with original service

manual.

Note 1:

AC Adaptor used on these movie camera is PV-DAC14D. However, DE-974FB is supplied as a replacement part for PV-

DAC14D. This AC Adaptor is supplied only as a unit.

3.2. About Lead Free Solder (PbF)

SDR-H18P / SDR-H20P / SDR-H18PC / SDR-H20PC

3.3. Precautions for Handling HDD

1. Handle HDD very carefully to prevent the static electricity and shock.

2. Set the HDD quickly after taking it out from the package. Make sure to put the HDD on buffer materials, etc.

3.3.1. Precautions at incoming process and for opening packages

SDR-H18P / SDR-H20P / SDR-H18PC / SDR-H20PC

3.3.2. Precautions for installing HDD

SDR-H18P / SDR-H20P / SDR-H18PC / SDR-H20PC

3.3.3. Precautions for inserting and removing HDD FPC

Make sure to use the tool (LSVQ0112) when locking and unlocking the lock lever of HDD FPC connector.

Do not lock the lock lever without inserting HDD FPC. Otherwise, the connector may be damaged.

SDR-H18P / SDR-H20P / SDR-H18PC / SDR-H20PC

Make sure to use the tool (LSVQ0112) when opening and closing the lock lever.

*See "Disassembly Procedures" (Fig. D4) for attaching to the unit.

SDR-H18P / SDR-H20P / SDR-H18PC / SDR-H20PC

Autres manuels pour SDR-H18P

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Panasonic Appareil photo numérique

Panasonic

Panasonic LUMIX VQT1D44 Manuel utilisateur

Panasonic

Panasonic Lumix DMC-G2K Manuel utilisateur

Panasonic

Panasonic DMC-FZ200K Instructions d'installation et d'entretien

Panasonic

Panasonic DMC-ZS110 Manuel du propriétaire

Panasonic

Panasonic Lumix DMC-LZ20 Instructions d'installation et d'entretien

Panasonic

Panasonic Lumix DC-FZ10002 Caractéristiques techniques

Panasonic

Panasonic DMC-TZ35 Caractéristiques techniques

Panasonic

Panasonic Lumix DMC-LZ20E Manuel utilisateur

Panasonic

Panasonic Lumix DMC-TZ57 Manuel utilisateur

Panasonic

Panasonic Lumix DMC-FS35 Manuel utilisateur

Panasonic

Panasonic LUMIX DMC-FZ7 Manuel utilisateur

Panasonic

Panasonic Lumix DMC-F2PC Manuel utilisateur

Panasonic

Panasonic Lumix DMC-FZ200 Caractéristiques techniques

Panasonic

Panasonic Lumix DMC-G2K Manuel utilisateur

Panasonic

Panasonic Lumix DMC-ZS5 Caractéristiques techniques

Panasonic

Panasonic Lumix DMC-FX700 Manuel utilisateur

Panasonic

Panasonic LUMIX DMC-FH20 Caractéristiques techniques

Panasonic

Panasonic LUMIX DMC-LS1EB Manuel utilisateur

Panasonic

Panasonic LUMIX DMC-LZ8 Manuel utilisateur

Panasonic

Panasonic Lumix DMC-FS15 Mode d’emploi

Panasonic

Panasonic Lumix DMC-FZ2 Manuel utilisateur

Panasonic

Panasonic LUMIX DC-TZ90GN Caractéristiques techniques

Panasonic

Panasonic DMC-LX7K Manuel utilisateur

Panasonic

Panasonic Lumix DMC-FS62 Manuel utilisateur

Manuels Appareil photo numérique populaires d'autres marques

Mercury

Mercury 350K Manuel utilisateur

Pentax

Pentax Optio LS 465 Manuel utilisateur

Sanyo

Sanyo VPC-S1085 Manuel utilisateur

GE SMART A1255 Manuel utilisateur

Point Grey

Point Grey Gazelle Manuel utilisateur

Nikon

Nikon COOLPIX A Manuel utilisateur

Pentax

Pentax P-5 Manuel utilisateur

BlazeVideo

BlazeVideo A280 Manuel utilisateur

Sony

Sony MCA-20 Manuel utilisateur

Sony

Sony Alpha DSLR-A290 Manuel utilisateur

ATIK Cameras

ATIK Cameras One Manuel utilisateur

CohuHD Costar

CohuHD Costar 3930 Series Manuel utilisateur

Leica

Leica M10-R Manuel utilisateur

FujiFilm

FujiFilm FinePix A700 Manuel utilisateur

Lorex

Lorex LNZ81P25 Series Manuel utilisateur

GE J1470S Manuel utilisateur

Sony

Sony A6700 Guide de l'utilisateur

Canon

Canon EOS ELAN7 Manuel utilisateur